Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM

DTC    C1552    PIG Power Supply Voltage Malfunction

DTC    C1554    Power Supply Relay Failure

for Preparation Click here


DESCRIPTION

When a problem occurs in the system, the power source relay circuit and the motor relay circuit are shut off to stop the power assist. The ECU must be replaced when there is a problem with the relays because the relays are built into the ECU.

DTC No.
DTC Detection Condition
Trouble Area
C1552
PIG power source circuit malfunction
  1. EPS fuse
  2. PIG power source circuit
  3. ECU wire sub-assembly
  4. Power steering ECU assembly
C1554
Power source relay circuit malfunction
  1. EPS fuse
  2. PIG power source circuit
  3. ECU wire sub-assembly
  4. Power steering ECU assembly

WIRING DIAGRAM


C250110E04


INSPECTION PROCEDURE

NOTICE:
If the power steering ECU assembly has been replaced with a new one, perform assist map writing and torque sensor zero point calibration (Click here).

HINT:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CONNECTOR CONNECTION CONDITION
  1. Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

    OK:
    The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.

  1. Check that the ground wire is securely installed with the bolt .

    OK:
    The ground wire is securely installed with the bolt.



NG
CONNECT CONNECTOR OR INSTALL GROUND WIRE
OK


2.READ VALUE USING INTELLIGENT TESTER
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / EMPS / Data List.

  1. Select the item "PIG Power Supply" in the Data List and read the value displayed on the intelligent tester.

    EMPS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    PIG Power Supply
    PIG power supply/
    Min.: 0.0000 V
    Max.: 20.1531 V
    9 to 16 V
    Always

    OK:
    The normal condition value is displayed on the intelligent tester.



NG
Go to step 3
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)  

3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)


    C239854E04
  1. Disconnect the Ij1 connector from the ECU wire sub-assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Ij1-1 (PIG) - Body ground
    Always
    9 to 16 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECU Wire Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)
C238941E06
  1. Disconnect the j2 connector from the power steering ECU assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    j2-2 (PGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY (Click here)
OK


5.CHECK ECU WIRE SUB-ASSEMBLY


    C238947E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    j2-1 (PIG) - Ij1-1 (PIG)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)
    *b
    Front view of wire harness connector
    (to Vehicle Wire Harness)



NG
REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY (Click here)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)