Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for TMMK Made)

DTC    B1622/81    Lost communication with Side Airbag Sensor RH

DTC    B1623/81    Side Airbag Sensor Assembly RH Initialization Incomplete

DTC    B1632/81    Lost Communication with Rear Airbag Sensor RH

DTC    B1633/81    Rear Airbag Sensor Assembly RH Initialization Incomplete

DTC    B1642/81    Lost Communication with Side Satellite Sensor Bus RH

DTC    B1692/81    Lost Communication with Door Side Airbag Sensor RH

DTC    B1693/81    Door Side Airbag Sensor RH Initialization Incomplete

for Preparation Click here


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH, rear seat airbag assembly RH, curtain shield airbag assembly RH and front seat outer belt assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH.
The side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.
These DTCs are stored when a malfunction is detected for the side collision sensor RH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1622/81
B1623/81
B1632/81
B1633/81
B1642/81
B1692/81
B1693/81
  1. The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit.
  1. Side airbag sensor assembly RH malfunction
  2. Side No. 2 airbag sensor assembly RH malfunction
  3. Door side airbag sensor RH malfunction
  4. Airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front door wire RH
  3. Side airbag sensor assembly RH
  4. Side No. 2 airbag sensor assembly RH
  5. Door side airbag sensor RH
  6. Airbag sensor assembly

WIRING DIAGRAM


C238366E33


INSPECTION PROCEDURE

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK CURRENT DTC
  1. Check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    Current DTC B1642 or 81 is output.
    A
    Current DTC B1623 or B1633 is output.
    B
    Current DTC B1692 or B1693 is output.
    C
    Current DTC B1622 or B1632 is output.
    D
    Current DTCs B1622, B1623, B1632, B1633, B1642, B1692, B1693 and 81 are not output.
    E

    HINT:
    1. DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the engine switch off and then on (IG) again.
    2. Codes other than current DTCs B1622, B1623, B1632, B1633, B1642, B1692, B1693 and 81 may be output at this time, but they are not related to this check.



B
Go to step 18

C
Go to step 33

D
Go to step 40

E
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK CONNECTORS
  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also check that the connectors that link the No. 2 floor wire and front door wire RH are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also disconnect the connectors that link the No. 2 floor wire and front door wire RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


3.CHECK NO. 2 FLOOR WIRE (OPEN)


    C238391E02
  1. Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-4 (BBR+) - O11-3 (BBR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


4.CHECK NO. 2 FLOOR WIRE (SHORT)
C238220E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-4 (BBR+) - O11-3 (BBR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


5.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C238220E02
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O11-4 (BBR+) - Body ground
    Engine switch on (IG)
    Below 1 V
    O11-3 (BBR-) - Body ground
    Engine switch on (IG)
    Below 1 V

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


6.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C238220E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    O11-3 (BBR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


7.CHECK NO. 2 FLOOR WIRE (OPEN)


    C238392E21
  1. Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - O11-2 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)
    *b
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


8.CHECK NO. 2 FLOOR WIRE (SHORT)
C238222E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - O11-2 (BCR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


9.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C238222E03
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - Body ground
    Engine switch on (IG)
    Below 1 V
    O11-2 (BCR-) - Body ground
    Engine switch on (IG)
    Below 1 V

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


10.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C238222E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    O11-2 (BCR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


11.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (OPEN)


    C238393E16
  1. Connect the connectors that link the No. 2 floor wire and front door wire RH.

  1. Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O46-1 (BDR+) - O46-2 (BDR-)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Door Side Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)
    *b
    Front view of wire harness connector
    (to Door Side Airbag Sensor RH)



NG
Go to step 43
OK


12.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT)


    C238394E16
  1. Disconnect the service wire from connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O46-1 (BDR+) - O46-2 (BDR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Door Side Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
Go to step 44
OK


13.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)


    C238394E16
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O46-1 (BDR+) - Body ground
    Engine switch on (IG)
    Below 1 V
    O46-2 (BDR-) - Body ground
    Engine switch on (IG)
    Below 1 V

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Door Side Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
Go to step 45
OK


14.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)


    C238394E16
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O46-1 (BDR+) - Body ground
    Always
    1 MΩ or higher
    O46-2 (BDR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Door Side Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
Go to step 46
OK


15.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    C238218E01
  1. Connect the connectors to the side No. 2 airbag sensor assembly RH, door side airbag sensor RH and airbag sensor assembly.

  1. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1642 or 81 is output.
    A
    DTC B1647 or 82 is output.
    B
    DTCs B1642, B1647, 81 and 82 are not output.
    C

    HINT:
    Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Airbag Sensor Assembly



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


16.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    C238223E01
  1. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1642 or 81 is output.
    A
    DTC B1647 or 82 is output.
    B
    DTCs B1642, B1647, 81 and 82 are not output.
    C

    HINT:
    Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly RH



B
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


17.CHECK DOOR SIDE AIRBAG SENSOR RH


    C238395E01
  1. Interchange the door side airbag sensor RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1642 or 81 is output.
    A
    DTC B1647 or 82 is output.
    B
    DTCs B1642, B1647, 81 and 82 are not output.
    C

    HINT:
    Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the door side airbag sensor RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Door Side Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly RH



B
REPLACE DOOR SIDE AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

18.CHECK HISTORY DTC
  1. Check for history DTCs (Click here).

    Result:
    Result
    Proceed to
    History DTCs B1622 and B1632 are not output.
    A
    History DTC B1622 is output.
    B
    History DTC B1632 is output.
    C

    HINT:
    Codes other than history DTCs B1622 and B1632 may be output at this time, but they are not related to this check.



B
Go to step 41

C
Go to step 42
A


19.CHECK CURRENT DTC
  1. Check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    Current DTC B1623 is output.
    A
    Current DTC B1633 is output.
    B

    HINT:
    Codes other than current DTCs B1623 and B1633 may be output at this time, but they are not related to this check.



B
Go to step 26
A


20.CHECK CONNECTORS
  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


21.CHECK NO. 2 FLOOR WIRE (OPEN)


    C238391E02
  1. Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-4 (BBR+) - O11-3 (BBR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


22.CHECK NO. 2 FLOOR WIRE (SHORT)


    C238220E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-4 (BBR+) - O11-3 (BBR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


23.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C238220E02
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O11-4 (BBR+) - Body ground
    Engine switch on (IG)
    Below 1 V
    O11-3 (BBR-) - Body ground
    Engine switch on (IG)
    Below 1 V

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


24.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C238220E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    O11-3 (BBR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


25.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    C238218E01
  1. Connect the connector to the airbag sensor assembly.

  1. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1623 is output.
    A
    DTC B1628 is output.
    B
    DTCs B1623 and B1628 are not output.
    C

    HINT:
    Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Airbag Sensor Assembly



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

26.CHECK CONNECTORS
  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


27.CHECK NO. 2 FLOOR WIRE (OPEN)


    C238392E21
  1. Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - O11-2 (BCR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector C.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *4
    Service Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)
    *b
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


28.CHECK NO. 2 FLOOR WIRE (SHORT)
C238222E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - O11-2 (BCR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


29.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    C238222E03
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - Body ground
    Engine switch on (IG)
    Below 1 V
    O11-2 (BCR-) - Body ground
    Engine switch on (IG)
    Below 1 V

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


30.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    C238222E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O11-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    O11-2 (BCR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly RH
    *3
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


31.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    C238218E01
  1. Connect the connector to the side No. 2 airbag sensor assembly RH.

  1. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1633 is output.
    A
    DTC B1638 is output.
    B
    DTCs B1633 and B1638 are not output.
    C

    HINT:
    Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Airbag Sensor Assembly



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


32.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    C238223E01
  1. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1633 is output.
    A
    DTC B1638 is output.
    B
    DTCs B1633 and B1638 are not output.
    C

    HINT:
    Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly RH



B
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

33.CHECK CONNECTORS
  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also check that the connectors that link the No. 2 floor wire and front door wire RH are properly connected.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also disconnect the connectors that link the No. 2 floor wire and front door wire RH.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


34.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (OPEN)


    C238393E16
  1. Connect the connectors that link the No. 2 floor wire and front door wire RH.

  1. Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O46-1 (BDR+) - O46-2 (BDR-)
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Door Side Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    Service Wire
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)
    *b
    Front view of wire harness connector
    (to Door Side Airbag Sensor RH)



NG
Go to step 43
OK


35.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT)


    C238394E16
  1. Disconnect the service wire from connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O46-1 (BDR+) - O46-2 (BDR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Door Side Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
Go to step 44
OK


36.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)


    C238394E16
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O46-1 (BDR+) - Body ground
    Engine switch on (IG)
    Below 1 V
    O46-2 (BDR-) - Body ground
    Engine switch on (IG)
    Below 1 V

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Text in Illustration 
    *1
    Door Side Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
Go to step 45
OK


37.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)


    C238394E16
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O46-1 (BDR+) - Body ground
    Always
    1 MΩ or higher
    O46-2 (BDR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Door Side Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *a
    Front view of wire harness connector
    (to Side No. 2 Airbag Sensor Assembly RH)



NG
Go to step 46
OK


38.CHECK DOOR SIDE AIRBAG SENSOR RH


    C238395E01
  1. Connect the connectors to the side No. 2 airbag sensor assembly RH.

  1. Interchange the door side airbag sensor RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1692 or B1693 is output.
    A
    DTC B1697 or B1698 is output.
    B
    DTCs B1692, B1693, B1697 and B1698 are not output.
    C

    HINT:
    Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the door side airbag sensor RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Door Side Airbag Sensor LH
    *2
    Side No. 2 Airbag Sensor Assembly RH



B
REPLACE DOOR SIDE AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


39.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    C238223E01
  1. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1692 or B1693 is output.
    A
    DTC B1697 or B1698 is output.
    B
    DTCs B1692, B1693, B1697 and B1698 are not output.
    C

    HINT:
    Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly RH



B
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

40.CHECK CURRENT DTC
  1. Check for current DTCs (Click here).

    Result:
    Result
    Proceed to
    Current DTC B1622 is output.
    A
    Current DTC B1632 is output.
    B

    HINT:
    Codes other than current DTCs B1622 and B1632 may be output at this time, but they are not related to this check.

  1. Turn the engine switch off.



B
Go to step 42
A


41.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    C238218E01
  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1622 is output.
    A
    DTC B1627 is output.
    B
    DTCs B1622 and B1627 are not output.
    C

    HINT:
    Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Airbag Sensor Assembly



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

42.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    C238223E01
  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the engine switch off.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1632 is output.
    A
    DTC B1637 is output.
    B
    DTCs B1632 and B1637 are not output.
    C

    HINT:
    Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

  1. Turn the engine switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
    Text in Illustration 
    *1
    Side No. 2 Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly RH



B
REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

43.CHECK FRONT DOOR WIRE RH (OPEN)


    C238396E19
  1. Disconnect the front door wire RH connector from the No. 2 floor wire.

    HINT:
    The service wire has already been inserted into connector E.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    JO1-1 (BDR+) - JO1-2 (BDR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector E.
    Text in Illustration 
    *1
    Door Side Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    Front Door Wire RH
    *4
    No. 2 Floor Wire
    *5
    Service Wire
    *a
    Front view of wire harness connector
    (to No. 2 Floor Wire)
    *b
    Front view of wire harness connector
    (to Door Side Airbag Sensor RH)



NG
REPLACE FRONT DOOR WIRE RH
OK

REPLACE NO. 2 FLOOR WIRE 

44.CHECK FRONT DOOR WIRE RH (SHORT)


    C238397E06
  1. Disconnect the front door wire RH connector from the No. 2 floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    JO1-1 (BDR+) - JO1-2 (BDR-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Door Side Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    Front Door Wire RH
    *4
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to No. 2 Floor Wire)



NG
REPLACE FRONT DOOR WIRE RH
OK

REPLACE NO. 2 FLOOR WIRE 

45.CHECK FRONT DOOR WIRE RH (SHORT TO B+)


    C238397E06
  1. Disconnect the front door wire RH connector from the No. 2 floor wire.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    JO1-1 (BDR+) - Body ground
    Engine switch on (IG)
    Below 1 V
    JO1-2 (BDR-) - Body ground
    Engine switch on (IG)
    Below 1 V

    Text in Illustration 
    *1
    Door Side Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    Front Door Wire RH
    *4
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to No. 2 Floor Wire)



NG
REPLACE FRONT DOOR WIRE RH
OK

REPLACE NO. 2 FLOOR WIRE 

46.CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)


    C238397E06
  1. Disconnect the front door wire RH connector from the No. 2 floor wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    JO1-1 (BDR+) - Body ground
    Always
    1 MΩ or higher
    JO1-2 (BDR-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Door Side Airbag Sensor RH
    *2
    Side No. 2 Airbag Sensor Assembly RH
    *3
    Front Door Wire RH
    *4
    No. 2 Floor Wire
    *a
    Front view of wire harness connector
    (to No. 2 Floor Wire)



NG
REPLACE FRONT DOOR WIRE RH
OK

REPLACE NO. 2 FLOOR WIRE