Home › Drivetrain ยท U660E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE

DIFFERENTIAL CASE > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT TRANSAXLE CASE OIL SEAL


    C196817E01
  1. Using SST, remove the front transaxle case oil seal from the transaxle housing.

    SST
    09308-00010  



2. REMOVE TRANSAXLE CASE OIL SEAL


    C196822E01
  1. Using SST, remove the transaxle case oil seal from the transaxle case sub-assembly.

    SST
    09308-00010  



3. INSPECT FRONT DIFFERENTIAL CASE


    C306378E02
  1. Using SST, rotate the front differential side gear as shown in the illustration.

    SST
    09528-52010   (09528-05030)

    Standard:
    The front differential side gear does not lock when rotated in either direction.

    1. If the front differential side gear locks, perform all inspections.
    2. If the front differential side gear still locks even after replacing the malfunctioning parts, replace the front differential case.
    3. Replace any parts that do not meet the specification.



4. INSPECT FRONT DIFFERENTIAL SIDE GEAR THRUST AMOUNT


    C306379E01
  1. Using SST and a dial indicator, measure the front differential side gear thrust amount.
    Text in Illustration 
    *a
    Front Differential Side Gear Thrust Amount

    SST
    09528-52010   (09528-05030)

    Front Differential Side Gear Thrust Amount:
    0.08 mm (0.00315 in.) or less

    HINT:
    1. Measure the front differential side gear thrust amount while slowly rotating the front differential side gear.
    1. Make sure to measure the front differential side gear thrust amount for both of the front differential side gears.

    If the result is not as specified, replace the 2 front differential side gears, 2 front differential pinions and 2 conical springs.



5. REMOVE FRONT DIFFERENTIAL RING GEAR


    C312836E03
  1. Put matchmarks on the front differential ring gear and front differential case.
    Text in Illustration 
    *a
    Matchmark



    C138532
  1. Remove the 12 bolts from the front differential ring gear.



    C312835
  1. Using a plastic hammer, tap on the front differential ring gear to remove it from the front differential case.



6. REMOVE FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN
  1. Secure the front differential case in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C309126
  1. Using a 5 mm pin punch and a hammer, remove the front differential pinion shaft straight pin from the front differential case.



7. REMOVE FRONT NO. 1 DIFFERENTIAL PINION SHAFT


    C309127
  1. Remove the front No. 1 differential pinion shaft from the front differential case.



8. INSPECT FRONT DIFFERENTIAL PINION BACKLASH


  1. Install SST as shown in the illustration and tighten it.


    C312292E01


    Text in Illustration 
    *a
    Turn
    *b
    Hold
    SST
    09528-52010   (09528-05010, 09953-05010)

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Secure the front differential case in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C309132E01
  1. Install the front No. 1 differential pinion shaft to the front differential pinion as shown in the illustration.
    Text in Illustration 
    *1
    Front No. 1 Differential Pinion Shaft

  1. Using a dial indicator, measure the front differential pinion backlash.

    Standard Backlash:
    0.15 mm (0.00591 in.) or less

    HINT:
    Select front No. 1 differential side gear thrust washers of the same thickness for both the right and left side.

    If the backlash is not as specified, replace the front No. 1 differential side gear thrust washers with washers of a different thickness. Use the table below to select a front No. 1 differential side gear thrust washer which will ensure that the backlash is within the specification.
    Front No. 1 Differential Side Gear Thrust Washer Thickness: 
    Part No.
    Thickness (mm (in.))
    41361-33020
    1.50 (0.0591)
    41361-33030
    1.55 (0.0610)
    41361-33040
    1.60 (0.0630)
    41361-33050
    1.65 (0.0650)
    41361-33060
    1.70 (0.0669)
    41361-33070
    1.75 (0.0689)
    41361-33080
    1.80 (0.0709)
    41361-33090
    1.85 (0.0728)
    41361-33100
    1.90 (0.0748)



9. REMOVE FRONT DIFFERENTIAL SIDE GEAR


  1. Install SST as shown in the illustration and tighten it.


    C312291E01


    Text in Illustration 
    *a
    Turn
    *b
    Hold
    SST
    09528-52010   (09528-05010, 09953-05010)

    NOTICE:
    Do not overtighten SST, as doing so will damage the front differential side gears, conical springs, front No. 1 differential side gear thrust washers and front differential case.

    HINT:
    1. Tighten SST until there is clearance between the front differential pinions and front differential side gears.
    2. When removing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.



    C309129E01
  1. Using SST as shown in the illustration, rotate the front differential side gear to remove the 2 front differential pinions and 2 front differential pinion thrust washers from the front differential case.
    Text in Illustration 
    *a
    Turn

    SST
    09528-52010   (09528-05030)

    NOTICE:
    Do not drop the front differential pinion and front differential pinion thrust washer.



    C309130E01
  1. Remove SST from the front differential case, and then remove the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs from the front differential case.
    Text in Illustration 
    *1
    Front Differential Side Gear
    *2
    Conical Spring
    *3
    Front No. 1 Differential Side Gear Thrust Washer

    NOTICE:
    Do not drop the front differential side gear, front No. 1 differential side gear thrust washer or conical spring.



10. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    C309435E01
  1. Using SST, remove the front differential case front tapered roller bearing (inner race) from the front differential case.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)
    09950-60010   (09951-00480)



    C196812E02
  1. Using SST, remove the front differential case front tapered roller bearing (outer race) and shim from the transaxle housing.

    SST
    09308-00010  



11. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


    C309436E01
  1. Using SST, remove the front differential case rear tapered roller bearing (inner race) from the front differential case.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)
    09950-60010   (09951-00480)



    C196814E01
  1. Using SST, remove the front differential case rear tapered roller bearing (outer race) from the transaxle case sub-assembly.

    SST
    09308-00010