Home › Drivetrain ยท U761E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE

DIFFERENTIAL CASE > DISASSEMBLY

for Preparation Click here



1. INSPECT FRONT DIFFERENTIAL CASE


    C317738E01
  1. Using SST, rotate the front differential side gear as shown in the illustration.

    SST
    09528-52010   (09528-05030)

    Standard:
    The front differential side gear does not lock when rotated in either direction.

    1. If the front differential side gear locks, perform all of the following inspections.
    2. If the front differential side gear still locks after replacing the malfunctioning parts, replace the front differential case.
    3. Replace any parts that do not meet the specifications.



2. REMOVE FRONT DIFFERENTIAL RING GEAR


    C317727E01
  1. Put matchmarks on the front differential ring gear and front differential case.
    Text in Illustration 
    *a
    Matchmark



    C317728
  1. Remove the 12 bolts.



    C317729
  1. Using a plastic hammer, tap on the front differential ring gear to remove it from the front differential case.



3. REMOVE FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN
  1. Secure the front differential case in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C317730
  1. Using a 5 mm pin punch and a hammer, remove the front differential pinion shaft straight pin from the front differential case.



4. REMOVE FRONT NO. 1 DIFFERENTIAL PINION SHAFT


    C317731
  1. Remove the front No. 1 differential pinion shaft from the front differential case.



5. INSPECT FRONT DIFFERENTIAL PINION BACKLASH


  1. Install SST as shown in the illustration and tighten it.


    C317739E01


    Text in Illustration 
    *a
    Turn
    *b
    Hold
    SST
    09528-52010   (09528-05010, 09953-05010)

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Secure the front differential case with front differential ring gear in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C317740E01
  1. Install the front No. 1 differential pinion shaft to the front differential pinion as shown in the illustration.
    Text in Illustration 
    *1
    Front No. 1 Differential Pinion Shaft

  1. Using a dial indicator, measure the front differential pinion backlash.

    Standard Backlash:
    0.20 mm (0.00787 in.) or less

    If the backlash is not as specified, replace the front No. 1 differential side gear thrust washers with washers of a different thickness. Use the table below to select front No. 1 differential side gear thrust washers which will ensure that the backlash is within the specification.

    HINT:
    Select front No. 1 differential side gear thrust washers of the same thickness for both the right and left side.

    Front No. 1 Differential Side Gear Thrust Washer Thickness: 
    Part No.
    Thickness (mm (in.))
    41361-73050
    0.90 (0.0354)
    41361-73010
    1.00 (0.0394)
    41361-73020
    1.10 (0.0433)
    41361-73030
    1.20 (0.0472)



6. REMOVE FRONT DIFFERENTIAL SIDE GEAR


  1. Install SST as shown in the illustration and tighten it.


    C317732E01


    Text in Illustration 
    *a
    Turn
    *b
    Hold
    SST
    09528-52010   (09528-05010, 09953-05010)

    NOTICE:
    Do not overtighten SST, as doing so will damage the front differential side gears, conical springs, front No. 1 differential side gear thrust washers and front differential case.

    HINT:
    1. Tighten SST to create the necessary clearance to remove the front differential pinions.
    2. When removing the front differential pinions, do not overtighten SST, as it is necessary to rotate the front differential side gears.



    C317733E01
  1. Install SST as shown in the illustration and rotate the front differential side gear to remove the 2 front differential pinions and 2 front differential pinion thrust washers from the front differential case.
    Text in Illustration 
    *a
    Turn

    SST
    09528-52010   (09528-05030)

    NOTICE:
    Do not drop the front differential pinions and front differential pinion thrust washers.



    C317734E01
  1. Remove SST from the front differential case, and then remove the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs from the front differential case.
    Text in Illustration 
    *1
    Front Differential Side Gear
    *2
    Conical Spring
    *3
    Front No. 1 Differential Side Gear Thrust Washer

    NOTICE:
    Do not drop the front differential side gears, front No. 1 differential side gear thrust washers or conical springs.