DIFFERENTIAL CASE > REASSEMBLY |
| 1. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
![]() |
Using SST and a press, install a new front differential case rear tapered roller bearing (inner race) to the front differential case.
![]() |
Using SST and a hammer, install a new front differential case rear tapered roller bearing (outer race) to the transaxle case sub-assembly.
| 2. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
![]() |
Using SST and a press, install a new front differential case front tapered roller bearing (inner race) to the front differential case.
Install the shim to the transaxle housing.
![]() |
Using SST and a hammer, install a new front differential case front tapered roller bearing (outer race) to the transaxle housing.
| 3. INSTALL FRONT DIFFERENTIAL SIDE GEAR |
![]() |
Coat the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs with ATF.
| *1 | Front Differential Side Gear |
| *2 | Conical Spring |
| *3 | Front No. 1 Differential Side Gear Thrust Washer |
![]() | ATF |
![]() |
Install the 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and 2 conical springs to the front differential case.
| *1 | Front Differential Side Gear |
| *2 | Conical Spring |
| *3 | Front No. 1 Differential Side Gear Thrust Washer |
Install SST as shown in the illustration and tighten it.

| *a | Turn | *b | Hold |
![]() |
Coat the 2 front differential pinions and 2 front differential pinion thrust washers with ATF.
![]() | ATF |
![]() |
Using SST as shown in the illustration, rotate the front differential side gear to install the 2 front differential pinions and 2 front differential pinion thrust washers to the front differential case.
| *a | Turn |
| 4. INSPECT FRONT DIFFERENTIAL PINION BACKLASH |
Install SST as shown in the illustration and tighten it.

| *a | Turn | *b | Hold |
Secure the front differential case in a vise between aluminum plates.
![]() |
Install the front No. 1 differential pinion shaft to the front differential pinion as shown in the illustration.
| *1 | Front No. 1 Differential Pinion Shaft |
Using a dial indicator, measure the front differential pinion backlash.
| Part No. | Thickness (mm (in.)) |
| 41361-33020 | 1.50 (0.0591) |
| 41361-33030 | 1.55 (0.0610) |
| 41361-33040 | 1.60 (0.0630) |
| 41361-33050 | 1.65 (0.0650) |
| 41361-33060 | 1.70 (0.0669) |
| 41361-33070 | 1.75 (0.0689) |
| 41361-33080 | 1.80 (0.0709) |
| 41361-33090 | 1.85 (0.0728) |
| 41361-33100 | 1.90 (0.0748) |
| 5. INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT |
![]() |
Coat the front No. 1 differential pinion shaft with ATF.
![]() | ATF |
Install the front No. 1 differential pinion shaft to the front differential case so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front differential case.
| 6. INSPECT FRONT DIFFERENTIAL CASE |
![]() |
Using SST, rotate the front differential side gear as shown in the illustration.
| 7. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN |
![]() |
Using a 5 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the front differential case.
![]() |
Using a chisel and hammer, stake the front differential case.
| 8. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD |
Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.
![]() |
Install the front differential case to the transaxle case sub-assembly.
![]() |
Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.
![]() |
Using SST, turn the front differential case right and left 2 or 3 times to settle the bearings.
Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.
| Part No. | Thickness (mm (in.)) |
| 90564-79054 | 2.000 (0.0787) |
| 90564-79055 | 2.025 (0.0797) |
| 90564-79056 | 2.050 (0.0807) |
| 90564-79057 | 2.075 (0.0817) |
| 90564-79058 | 2.100 (0.0827) |
| 90564-79059 | 2.125 (0.0837) |
| 90564-79060 | 2.150 (0.0846) |
| 90564-79061 | 2.175 (0.0856) |
| 90564-79062 | 2.200 (0.0866) |
| 90564-79063 | 2.225 (0.0876) |
| 90564-79064 | 2.250 (0.0886) |
| 90564-79065 | 2.275 (0.0896) |
| 90564-79066 | 2.300 (0.0906) |
| 90564-79067 | 2.325 (0.0915) |
| 90564-79068 | 2.350 (0.0925) |
| 90564-79069 | 2.375 (0.0935) |
| 90564-79070 | 2.400 (0.0945) |
| 90564-79071 | 2.425 (0.0955) |
| 90564-79072 | 2.450 (0.0965) |
| 90564-79073 | 2.475 (0.0974) |
| 90564-79074 | 2.500 (0.0984) |
| 90564-79075 | 2.525 (0.0994) |
| 90564-79076 | 2.550 (0.100) |
| 90564-79077 | 2.575 (0.101) |
| 90564-79078 | 2.600 (0.102) |
| 90564-79079 | 2.625 (0.103) |
| 90564-79080 | 2.650 (0.104) |
| 90564-79081 | 2.675 (0.105) |
| 90564-79082 | 2.700 (0.106) |
| 90564-79083 | 2.725 (0.107) |
| 90564-79084 | 2.750 (0.108) |
| 90564-79085 | 2.775 (0.109) |
| 90564-79086 | 2.800 (0.110) |
| 90564-79087 | 2.825 (0.111) |
| 90564-79088 | 2.850 (0.112) |
| 90564-79089 | 2.875 (0.113) |
![]() |
Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.
![]() |
Remove the front differential case from the transaxle case sub-assembly.
| 9. INSTALL FRONT DIFFERENTIAL RING GEAR |
![]() |
Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).
Clean the contact surface of the front differential case.
![]() |
Align the matchmarks, and install the front differential ring gear to the front differential case quickly.
| *a | Matchmark |
![]() |
Install the 12 bolts.
| 10. INSTALL TRANSAXLE CASE OIL SEAL |
Coat the lip of a new transaxle case oil seal with MP grease.
![]() |
Using SST and a hammer, install the transaxle case oil seal to the transaxle case sub-assembly.
| 11. INSTALL FRONT TRANSAXLE CASE OIL SEAL |
![]() |
Coat the lip of a new front transaxle case oil seal with MP grease.
Using SST and a hammer, install the front transaxle case oil seal to the transaxle housing.