POWER MIRROR CONTROL SYSTEM (w/ Memory) > OPERATION CHECK |
| CHECK REMOTE CONTROL MIRROR FUNCTION |
Turn the engine switch on (IG).
With the mirror select switch set to L, check that the outer rear view mirror LH surface moves up, down, left and right normally.
With the mirror select switch set to R, check that the outer rear view mirror RH surface moves up, down, left and right normally.
| CHECK MEMORY AND REACTIVATION FUNCTION |
![]() |
Turn the engine switch on (IG) and move the shift lever to P.
| *1 | SET Switch |
| *2 | M1 Switch |
| *3 | M2 Switch |
![]() |
Check the M1 switch.
Using the mirror adjust switch, turn the mirror surface to the full left position.
| *a | Turn to Left Fully |
Check that the buzzer sounds for 0.5 seconds and the seat position is memorized when the M1 switch is pressed within 3 seconds of the SET switch being pressed.
Using the outer mirror switch assembly, turn the mirror surface to the full right position.
Press the M1 switch.
Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded full left position.
![]() |
Check the M2 switch.
Using the mirror adjust switch assembly, turn the mirror surface to the full right position.
| *a | Turn to Right Fully |
Check that the buzzer sounds for 0.5 seconds and the seat position is memorized when the M2 switch is pressed within 3 seconds of the SET switch being pressed.
Using the outer mirror switch assembly, turn the mirror surface to the full left position.
Press the M2 switch.
Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded full right position.
| CHECK POWER RETRACTABLE MIRROR FUNCTION |
Turn the engine switch on (IG).
At each outer rear view mirror assembly position, check the retractable mirror operation when operating the retractable outer mirror switch.
![]() |
Move the mirrors to the driving position.
Turn the retractable outer mirror switch to the retract position.
Check that the right and left outer rear view mirror assemblies move from the driving position to the retracted position.
![]() |
Move the mirrors to the driving position.
Move one of the outer rear view mirror assemblies to the forward position by hand.
Turn the retractable outer mirror switch to the retract position.
Check that the outer rear view mirror assembly in the forward position moves to the retracted position, and check that the other mirror moves to the retracted position.
![]() |
Move the outer rear view mirror assemblies to the driving position.
Move one of the outer rear view mirror assemblies to the retracted position by hand.
Turn the retractable outer mirror switch to the retract position.
Check that the outer rear view mirror assembly in the driving position moves to the retracted position.
![]() |
Move the mirrors to the retracted position.
Turn the retractable outer mirror switch to the driving position.
Check that the right and left mirrors move from the retracted position to the driving position.
![]() |
Move the mirrors to the retracted position.
Move one of the outer rear view mirror assemblies to the driving position by hand.
Turn the retractable outer mirror switch to the driving position.
Check that the retracted outer rear view mirror assembly moves to the driving position.
Check the operation of the outer rear view mirror assembly according to retractable outer mirror switch operations and engine switch condition.
When the outer rear view mirror assembly is operating, turn the engine switch off and check that the mirror operation stops immediately.
This time, turn the engine switch on (ACC) and press the retractable outer mirror switch. Check that the outer rear view mirror assembly operates in the opposite direction.
Check the operation of the outer rear view mirror assembly when it is blocked by an obstacle.
When the outer rear view mirror is moving to the retracted or driving position, block the outer rear view mirror assembly by hand. Check that the mirror stops moving.
With the outer rear view mirror assembly stopped partway, push the retractable outer mirror switch. Check that the outer rear view mirror assembly moves in the opposite direction.
| CHECK REVERSE SHIFT-LINKED OPERATION OF MIRRORS |
![]() |
Turn the engine switch on (IG).
Set the mirror select switch to L or R.
| *1 | Mirror Select Switch |
| *a | Downward |
Check that the mirror surface turns downward when the shift lever is moved to R.
Check that the mirror surface position returns to the original position when one of the following conditions is met:
| CHECK MEMORY CALL FUNCTION |
Memory call function check
With a electrical key transmitter sub-assembly recognition code registered:
Perform a wireless door unlock operation and check that opening the driver side door causes the following:
With the engine switch on (IG) and the driver door closed, press and hold the M1 or M2 switch while carrying the electrical key transmitter sub-assembly. The main body ECU (multiplex network body ECU) will enter electrical key transmitter sub-assembly recognition code registration mode to allow a key to be linked to mirror surface memory position.
When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly sounds once (0.5 seconds).
With the engine switch on (IG) and the driver side door closed, press and hold the SET switch while carrying the electrical key transmitter sub-assembly. The main body ECU (multiplex network body ECU) will enter electrical key transmitter sub-assembly recognition code deletion mode.
When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly sounds twice (0.1 seconds each time).
| EMERGENCY STOP FUNCTION |
While a memory call function is operating, check that any one of the following actions will stop the memory call operation: 1) pressing the SET, M1or M2 switch, 2) moving the shift lever to R, 3) moving the mirror surface manually, or 4) moving the mirror surface to the uppermost, lowermost, leftmost or rightmost position.