Home › Engine / Hybrid System · 2GR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0660    Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)

for Preparation Click here


DESCRIPTION

This circuit opens and closes the intake air control valve assembly (built into intake air surge tank assembly) in response to changes in the engine load in order to increase the intake efficiency using the acoustic control induction system.
When the engine speed is between 0 and 4200 rpm and the throttle valve opening angle is 60° or more, the ECM supplies current to the actuator (on status), to close the intake air control valve assembly. Under other conditions, the intake air control valve assembly is open.

G041080E31


DTC No.
DTC Detection Condition
Trouble Area
P0660
The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
  1. Voltage of terminal acoustic control induction system of the ECM is low when the actuator is off
  2. The engine has been started
  1. Open or short in intake air control valve assembly circuit
  2. Intake air surge tank assembly (intake air control valve assembly)
  3. No. 1 integration relay
  4. ECM

WIRING DIAGRAM


A268233E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR INTAKE CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Intake Control.

  1. Check if operating noise can be heard when operating the intake air control valve assembly using the tester.

    OK:
    Operating noise can be heard.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT INTAKE AIR SURGE TANK ASSEMBLY (INTAKE AIR CONTROL VALVE ASSEMBLY OPERATION)
  1. Inspect the intake air surge tank assembly (intake air control valve assembly) (Click here).



NG
REPLACE INTAKE AIR SURGE TANK ASSEMBLY (Click here)
OK


3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INTAKE AIR CONTROL VALVE ASSEMBLY)


    A194326E13
  1. Disconnect the intake air control valve assembly connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E46-2 - Body ground
    Engine switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Intake Air Control Valve Assembly)



NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ASSEMBLY - ECM)
  1. Disconnect the intake air control valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E46-1 - E26-47 (ACIS)
    Always
    Below 1 Ω
    E46-1 or E26-47 (ACIS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ASSEMBLY - NO. 1 INTEGRATION RELAY)
  1. Disconnect the intake air control valve assembly connector.

  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E46-2 - 1A-8
    Always
    Below 1 Ω
    E46-2 or 1A-8 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)