Home › Power Source / Network ยท NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > SYSTEM DIAGRAM

for Preparation Click here



OVERALL CAN BUS DIAGRAM (for LHD)


  1. The CAN communication system is composed of 3 buses.


    C310574E01


    Text in Illustration 
    *1
    V Bus
    *2
    Sub Bus 1
    *3
    Sub Bus 2
    *4
    V Bus Terminating Resistor
    *5
    Sub Bus 1 Terminating Resistor
    *6
    Sub Bus 2 Terminating Resistor
    *7
    ECM
    (for V Bus)
    *8
    Main Body ECU (Multiplex Network Body ECU)
    (for V Bus and Sub Bus 1)
    *9
    Airbag Sensor Assembly
    (for V Bus)
    *10
    Power Steering ECU with Motor Assembly
    (for V Bus)
    *11
    Air Conditioning Amplifier Assembly
    (for V Bus)
    *12
    1. Navigation receiver assembly*1
    2. Radio and Display Receiver Assembly*2
    (for V Bus)
    *13
    Network Gateway ECU*3
    (for V Bus and Sub Bus 2)
    *14
    Steering Sensor
    (for V Bus)
    *15
    Smart Key ECU Assembly (Certification ECU)*4
    (for V Bus)
    *16
    Brake Actuator Assembly
    (for V Bus)
    *17
    Clearance Warning ECU Assembly*5
    (for V Bus)
    *18
    DLC3
    (for V Bus)
    *19
    AFS ECU*6
    (for V Bus)
    *20
    Inner Rear View Mirror Assembly*7
    (for V Bus)
    *21
    Combination Meter Assembly
    (for V Bus)
    *22
    Multiplex Tilt and Telescopic ECU*8
    (for Sub Bus 1)
    *23
    Outer Mirror Control ECU Assembly (for Driver Side)*9
    (for Sub Bus 1)
    *24
    Outer Mirror Control ECU Assembly (for Front Passenger Side)*9
    (for Sub Bus 1)
    *25
    Position Control ECU and Switch Assembly (for Driver Side)*9
    (for Sub Bus 1)
    *26
    CAN No. 5 Junction Connector
    (for Sub Bus 1)
    *27
    Blind Spot Monitor Sensor RH*10
    (for Sub Bus 2)
    *28
    Rear Television Camera Assembly*11
    (for Sub Bus 2)
    *29
    CAN No. 9 Junction Connector
    (for Sub Bus 2)
    -
    -
    1. *1: for Navigation Receiver Type
    2. *2: for Radio and Display Type
    3. *3: w/ Network Gateway ECU
    4. *4 w/ Smart Entry and Start System
    5. *5: w/ Toyota Parking Assist-sensor System
    6. *6: w/ AFS
    7. *7: w/ Automatic High Beam System
    8. *8: w/ Power Tilt and Power Telescopic Steering Column System
    9. *9: w/ Seat Position Memory System
    10. *10: w/ Blind Spot Monitor System
    11. *11: for Radio and Display Type (w/ Parking Assist Monitor System without Parallel Parking Assist Function)

HINT:
  1. The main body ECU (multiplex network body ECU) functions as a gateway between the V bus and sub bus 1.
  2. The network gateway ECU functions as a gateway between the V bus and sub bus 2.
  3. Refer to the following bus wiring diagrams for details.


V BUS (for LHD)

C310575E01


C310576E01

HINT:
The CAN communication system connects to other networks via ECUs that function as a gateway (Click here).


SUB BUS 1 (for LHD)

C310946E01


SUB BUS 2 (for LHD)

C313123E01


OVERALL CAN BUS DIAGRAM (for RHD)


  1. The CAN communication system is composed of 1 bus.


    C269147E02


    Text in Illustration 
    *1
    V Bus
    *2
    V Bus Terminating Resistor
    *3
    ECM
    (for V Bus)
    *4
    Main Body ECU (Multiplex Network Body ECU)
    (for V Bus)
    *5
    Airbag Sensor Assembly
    (for V Bus)
    *6
    Power Steering ECU with Motor Assembly
    (for V Bus)
    *7
    Air Conditioning Amplifier Assembly
    (for V Bus)
    *8
    Radio and Display Receiver Assembly*
    (for V Bus)
    *9
    Steering Sensor
    (for V Bus)
    *10
    Smart Key ECU Assembly (Certification ECU)
    (for V Bus)
    *11
    Brake Actuator Assembly
    (for V Bus)
    *12
    Clearance Warning ECU Assembly
    (for V Bus)
    *13
    DLC3
    (for V Bus)
    *14
    Combination Meter Assembly
    (for V Bus)
    *: for Radio and Display Type

    HINT:
    Refer to the following bus wiring diagrams for details.


V BUS (for RHD)

C241001E09


C269148E02

HINT:
The CAN communication system connects to other networks via ECUs that function as a gateway (Click here).