Home › Drivetrain ยท U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE BREATHER PLUG HOSE


    C190663
  1. Using a screwdriver, remove the breather plug hose from the transaxle case sub-assembly.



    C134952E04
  1. Using a screwdriver, remove the No. 1 breather plug (ATM) and No. 2 breather plug (ATM) from the breather plug hose.
    Text in Illustration 
    *1
    No. 1 Breather Plug (ATM)
    *2
    Breather Plug Hose
    *3
    No. 2 Breather Plug (ATM)
    *4
    O-ring

  1. Using a screwdriver, remove the O-ring from the No. 2 breather plug (ATM).



2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C136685
  1. Remove the nut, washer and transmission control shaft lever from the manual valve lever shaft sub-assembly.



    C136686
  1. Remove the 2 bolts and park/neutral position switch assembly from the transaxle case sub-assembly.

    NOTICE:
    Before removing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to remove the park/ neutral position switch assembly straight along the manual valve lever shaft sub-assembly while being careful not to deform the plate spring that supports the manual valve lever shaft sub-assembly. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.



3. REMOVE OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)


    C289626
  1. Remove the oil cooler tube union (outlet oil cooler union) from the transaxle case sub-assembly.

  1. Remove the O-ring from the oil cooler tube union (outlet oil cooler union).



4. REMOVE OIL COOLER TUBE UNION (INLET OIL COOLER UNION)


    C289627
  1. Remove the oil cooler tube union (inlet oil cooler union) from the transaxle case sub-assembly.

  1. Remove the O-ring from the oil cooler tube union (inlet oil cooler union).



5. REMOVE NO. 1 TRANSAXLE CASE PLUG


    C134958
  1. Remove the 3 No. 1 transaxle case plugs from the transaxle case sub-assembly.

  1. Using a screwdriver, remove the 3 O-rings from the 3 No. 1 transaxle case plugs.



6. REMOVE NO. 2 TRANSAXLE CASE PLUG


    C134959
  1. Using a 6 mm hexagon socket wrench, remove the 3 No. 2 transaxle case plugs from the transaxle housing.

  1. Remove the gasket from each of the 3 No. 2 transaxle case plugs.



7. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY


    C136444
  1. Support the automatic transaxle assembly with wooden blocks.



8. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    C134961
  1. Using a 6 mm hexagon socket wrench, remove the overflow plug from the automatic transaxle oil pan sub-assembly.

  1. Remove the gasket from the overflow plug.



    C141531
  1. Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.



    C134962
  1. Remove the 18 bolts, automatic transaxle oil pan sub-assembly and automatic transaxle oil pan gasket from the transaxle case sub-assembly.



    C134963E04
  1. Remove the 2 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.
    Text in Illustration 
    *1
    Transmission Oil Cleaner Magnet



9. INSPECT TRANSMISSION OIL CLEANER MAGNET


    C138722
  1. Use the removed transmission oil cleaner magnets to collect any steel chips. Examine the chips and particles in the automatic transaxle oil pan sub-assembly and on the transmission oil cleaner magnets to determine what type of wear has occurred in the automatic transaxle assembly:

    Result:
    Steel (magnetic):
    Bearing, gear and plate wear
    Brass (non-magnetic):
    Bushing wear



10. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


    C136687
  1. Remove the 2 bolts and valve body oil strainer assembly from the transmission valve body assembly.



    C136688E04
  1. Remove the O-ring from the valve body oil strainer assembly.
    Text in Illustration 
    *1
    O-ring



11. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    C136689
  1. Remove the 11 bolts and transmission valve body assembly from the transaxle case sub-assembly.

    NOTICE:
    When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case sub-assembly to interfere with each other.



12. REMOVE TRANSAXLE CASE GASKET


    C136429E01
  1. Remove the 2 transaxle case gaskets from the transaxle case sub-assembly.



13. INSPECT INPUT SHAFT SUB-ASSEMBLY END PLAY


    C136696
  1. Using a dial indicator, measure the input shaft sub-assembly end play.

    End Play:
    0.012 to 1.250 mm (0.000473 to 0.0492 in.)



14. REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY


    C136430
  1. Remove the refill plug from the rear transaxle cover sub-assembly.

  1. Remove the gasket from the refill plug.



    C288350
  1. Remove the 3 No. 1 automatic transaxle case plugs from the rear transaxle cover sub-assembly.

  1. Using a screwdriver, remove the 3 O-rings from the 3 No. 1 automatic transaxle case plugs.



    C291004
  1. Remove the 14 bolts from the rear transaxle cover sub-assembly.

  1. Using a brass bar and a hammer, tap on the circumference of the rear transaxle cover sub-assembly to remove the rear transaxle cover sub-assembly from the transaxle case sub-assembly.



    C136432E01
  1. Using a screwdriver, remove the 3 O-rings from the transaxle case sub-assembly.



    C297890E01
  1. Remove the thrust needle roller bearing and thrust needle roller race from the rear transaxle cover sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Needle Roller Race



    C299131E01
  1. Using a screwdriver, remove the 2 oil seal rings from the rear transaxle cover sub-assembly.
    Text in Illustration 
    *1
    Oil Seal Ring



    C162442E01
  1. Using a T30 "TORX" socket wrench, remove the 2 "TORX" screws and rear transaxle cover plate from the rear transaxle cover sub-assembly.



    C194888E05
  1. Using SST, remove the needle roller bearing from the rear transaxle cover sub-assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09319-60020  



15. REMOVE DIRECT MULTIPLE DISC CLUTCH ASSEMBLY


    C136442E02
  1. Remove the direct multiple disc clutch assembly from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Direct Multiple Disc Clutch Assembly
    *2
    Thrust Needle Roller Bearing

  1. Remove the thrust needle roller bearing from the direct multiple disc clutch assembly.



    C296565E01
  1. Using a screwdriver, remove the intermediate shaft oil seal from the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Intermediate Shaft Oil Seal
    *2
    O-ring

  1. Using a screwdriver, remove the O-ring from the direct multiple disc clutch assembly.



16. REMOVE DIRECT MULTIPLE DISC CLUTCH SNAP RING


    C136433
  1. Using a screwdriver, remove the direct multiple disc clutch snap ring from the direct multiple disc clutch assembly.



    C136434
  1. Remove the No. 2 direct clutch piston from the direct multiple disc clutch assembly.



17. REMOVE NO. 2 CLUTCH DISC


    C136435E03
  1. Remove the No. 2 clutch flange, 3 No. 2 clutch discs and 3 No. 2 clutch plates from the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    No. 2 Clutch Plate
    *2
    No. 2 Clutch Disc
    *3
    No. 2 Clutch Flange



18. INSPECT NO. 2 CLUTCH DISC


    C138267
  1. Check if the contact surfaces of the No. 2 clutch discs, No. 2 clutch plates and No. 2 clutch flange are worn or burnt.

    NOTICE:
    1. If the lining of any No. 2 clutch disc is peeled off or discolored, or even if part of the groove is damaged, replace all No. 2 clutch discs.
    2. Before assembling new No. 2 clutch discs, soak them in ATF for at least 15 minutes.

    If necessary, replace them.



19. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


    C136436
  1. Using a snap ring expander, remove the snap ring from the direct multiple disc clutch assembly.



    C136437
  1. Remove the rear planetary sun gear assembly from the direct multiple disc clutch assembly.



    C136438E05
  1. Remove the thrust needle roller bearing and thrust needle roller race from the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Needle Roller Race



20. INSPECT REAR PLANETARY SUN GEAR ASSEMBLY


    C138266
  1. Using a caliper gauge, measure the inside diameter of the bushings of the rear planetary sun gear assembly.

    Standard Inside Diameter:
    25.580 to 25.601 mm (1.0071 to 1.0079 in.)

    Maximum Inside Diameter:
    25.601 mm (1.0079 in.)

    If the inside diameter is greater than the maximum, replace the rear planetary sun gear assembly.



21. REMOVE NO. 1 CLUTCH DISC


    C136445
  1. Using 2 screwdrivers, remove the 2 snap rings from the direct multiple disc clutch assembly.



    C136446E03
  1. Remove the No. 1 clutch flange, 4 No. 1 clutch discs and 4 No. 1 clutch plates from the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    No. 1 Clutch Flange
    *2
    No. 1 Clutch Plate
    *3
    No. 1 Clutch Disc



22. INSPECT NO. 1 CLUTCH DISC


    C138265
  1. Check if the contact surfaces of the No. 1 clutch discs, No. 1 clutch plates and No. 1 clutch flange are worn or burnt.

    NOTICE:
    1. If the lining of any No. 1 clutch disc is peeled off or discolored, or even if part of the groove is damaged, replace all No. 1 clutch discs.
    2. Before assembling new No. 1 clutch discs, soak them in ATF for at least 15 minutes.

    If necessary, replace them.



23. REMOVE TRANSAXLE HOUSING


    C136447E04
  1. Remove the 20 bolts from the transaxle housing.

  1. Using a brass bar and a hammer, tap on the circumference of the transaxle housing to remove the transaxle housing from the transaxle case sub-assembly.



24. REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE


    C194889E01
  1. Using SST, remove the counter driven gear front tapered roller bearing outer race and shim from the transaxle housing.

    SST
    09308-00010  



25. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


    C136449E01
  1. Remove the bolt, clamp and differential gear lube apply tube from the transaxle housing.



26. REMOVE FRONT OIL PUMP ASSEMBLY


    C136450E02
  1. Remove the 7 bolts and front oil pump assembly from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Gasket

  1. Remove the gasket from the front oil pump assembly.



    C293908E01
  1. Remove the thrust needle roller race from the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Race



    C294585E05
  1. Remove the thrust needle roller bearing from the counter drive gear nut.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    O-ring

  1. Remove the O-ring from the transaxle case sub-assembly.



27. REMOVE FRONT OIL PUMP BODY O-RING


    C293910
  1. Remove the front oil pump body O-ring from the front oil pump body sub-assembly.



28. REMOVE NO. 3 BRAKE DISC


    C136451E03
  1. Using a screwdriver, remove the snap ring from the front oil pump assembly.
    Text in Illustration 
    *1
    Snap Ring



    C136452E02
  1. Remove the 2 No. 3 brake flanges, 3 No. 3 brake discs and 2 No. 3 brake plates from the front oil pump assembly.
    Text in Illustration 
    *1
    No. 3 Brake Flange
    *2
    No. 3 Brake Plate
    *3
    No. 3 Brake Disc



29. INSPECT NO. 3 BRAKE DISC


    C138255
  1. Check if the contact surfaces of the No. 3 brake discs, No. 3 brake plates and No. 3 brake flanges are worn or burnt.

    NOTICE:
    1. If the lining of any No. 3 brake disc is peeled off or discolored, or even if part of the groove is damaged, replace all No. 3 brake discs.
    2. Before assembling new No. 3 brake discs, soak them in ATF for at least 15 minutes.

    If necessary, replace them.



30. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY


    C136458
  1. Remove the underdrive planetary gear assembly from the front oil pump assembly.



31. REMOVE NO. 3 BRAKE HUB


    C136454
  1. Remove the No. 3 brake hub from the underdrive planetary gear assembly.



    C136455E05
  1. Remove the thrust needle roller bearing and thrust needle roller race from the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Race
    *2
    Thrust Needle Roller Bearing



32. REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY


    C290582E01
  1. While expanding the snap ring with snap ring expander, remove the planetary sun gear sub-assembly from the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Planetary Sun Gear Sub-assembly
    *2
    Underdrive Planetary Gear Assembly
    *3
    Snap Ring

  1. Remove the snap ring from the underdrive planetary gear assembly.



33. INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY


    C291374
  1. Using a feeler gauge, measure the clearance between the underdrive planetary gear assembly and pinion gear at 4 points.

    Standard Clearance:
    0.18 to 0.54 mm (0.00709 to 0.0213 in.)

    If the clearance is greater than the standard clearance, replace the underdrive planetary gear assembly.



34. INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY


    C138259
  1. Using a caliper gauge, measure the inside diameter of the bushings of the planetary sun gear sub-assembly.

    Standard Inside Diameter:
    25.525 to 25.546 mm (1.0049 to 1.0057 in.)

    Maximum Inside Diameter:
    25.546 mm (1.0057 in.)

    If the inside diameter is greater than the maximum, replace the planetary sun gear sub-assembly.



35. REMOVE INPUT SHAFT SUB-ASSEMBLY


    C136459
  1. Remove the input shaft sub-assembly from the front oil pump assembly.



    C136460E05
  1. Remove the thrust needle roller bearing and thrust needle roller race from the input shaft sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Race
    *2
    Thrust Needle Roller Bearing
    *3
    Input Shaft Oil Seal Ring
    *4
    Input Shaft Sub-assembly

  1. Using a screwdriver, remove the 3 input shaft oil seal rings from the input shaft sub-assembly.



36. REMOVE UNDERDRIVE PLANETARY SUN GEAR


    C136461E02
  1. Remove the underdrive planetary sun gear from the front oil pump assembly.
    Text in Illustration 
    *1
    Underdrive Planetary Sun Gear
    *2
    Thrust Needle Roller Bearing

  1. Remove the thrust needle roller bearing from the front oil pump assembly.



37. REMOVE NO. 1 BRAKE DISC


    C153477E02
  1. Using a screwdriver, remove the 2 snap rings and brake snap ring stopper from the front oil pump assembly.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Brake Snap Ring Stopper



    C136463E04
  1. Remove the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates from the front oil pump assembly.
    Text in Illustration 
    *1
    No. 1 Brake Flange
    *2
    No. 1 Brake Plate
    *3
    No. 1 Brake Disc



38. INSPECT NO. 1 BRAKE DISC


    C138255
  1. Check if the contact surfaces of the No. 1 brake discs, No. 1 brake plates and No. 1 brake flange are worn or burnt.

    NOTICE:
    1. If the lining of any No. 1 brake disc is peeled off or discolored, or even if part of the groove is damaged, replace all No. 1 brake discs.
    2. Before assembling new No. 1 brake discs, soak them in ATF for at least 15 minutes.

    If necessary, replace them.



39. REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C136464
  1. Remove the 3 2nd brake piston return spring sub-assemblies from the front oil pump assembly.



40. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C138254
  1. Using a vernier caliper, measure the free length of the 3 2nd brake piston return spring sub-assemblies including the spring seats.

    Standard Free Length:
    23.85 mm (0.939 in.)

    If the free length is shorter than the standard free length, replace the 2nd brake piston return spring sub-assembly.



41. REMOVE NO. 1 BRAKE PISTON


    C136465
  1. While holding the front oil pump assembly by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the front oil pump assembly to remove the No. 1 brake piston.



    C136466E03
  1. Using a screwdriver, remove the 2 O-rings from the No. 1 brake piston.
    Text in Illustration 
    *1
    O-ring



42. REMOVE FRONT DIFFERENTIAL CASE


    C136467
  1. Remove the front differential case from the transaxle case sub-assembly.



43. REMOVE COUNTER DRIVE GEAR NUT


    C136698E01
  1. Using SST and a hammer, release the staked part of the front planetary gear assembly.

    SST
    09930-00010  



    C299132E01
  1. Turn the manual valve lever shaft sub-assembly 2 notches counterclockwise to set it to the P position as shown in the illustration.



    C136468E01
  1. Using SST, remove the counter drive gear nut from the front planetary gear assembly.

    SST
    09387-00130  



44. REMOVE COUNTER DRIVEN GEAR


    C299133E01
  1. Turn the manual valve lever shaft sub-assembly 2 notches clockwise to set it to the N position as shown in the illustration.



    C136469
  1. Remove the counter driven gear from the transaxle case sub-assembly.



45. REMOVE COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING


    C324774E01
  1. Using SST, remove the counter driven gear front tapered roller bearing from the counter driven gear.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00400)



46. REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING


    C324775E01
  1. Using SST, remove the counter driven gear rear tapered roller bearing from the counter driven gear.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)
    09950-60010   (09951-00320)



47. REMOVE COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE


    C194892E01
  1. Using SST, remove the counter driven gear rear tapered roller bearing outer race from the transaxle case sub-assembly.

    SST
    09308-00010  



48. REMOVE PAWL SHAFT CLAMP


    C136472
  1. Remove the bolt and pawl shaft clamp from the transaxle case sub-assembly.



49. REMOVE PAWL STOPPER PLATE


    C136473
  1. Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.



50. REMOVE PARKING LOCK SLEEVE


    C136474
  1. Remove the parking lock sleeve from the transaxle case sub-assembly.



51. REMOVE PARKING LOCK PAWL


    C136475E02
  1. Remove the spring, parking lock pawl pin, parking lock pawl shaft and parking lock pawl from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Parking Lock Pawl Shaft
    *2
    Parking Lock Pawl
    *3
    Spring
    *4
    Parking Lock Pawl Pin



52. REMOVE ONE-WAY CLUTCH ASSEMBLY


    C141525
  1. Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.



    C141526E02
  1. Remove the one-way clutch assembly with planetary ring gear from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    One-way Clutch Assembly with Planetary Ring Gear
    *2
    Thrust Needle Roller Bearing

  1. Remove the thrust needle roller bearing from the front planetary gear assembly.



53. INSPECT ONE-WAY CLUTCH ASSEMBLY


    C189425E05
  1. Temporarily install the one-way clutch assembly to the planetary ring gear.
    Text in Illustration 
    *1
    Planetary Ring Gear
    *2
    One-way Clutch Assembly
    *a
    Free
    *b
    Lock

  1. Make sure that the one-way clutch assembly turns freely counterclockwise and locks when turned clockwise.
    If the one-way clutch assembly does not operate normally, replace it.



54. REMOVE PLANETARY RING GEAR


    C201345E02
  1. Remove the planetary ring gear from the one-way clutch assembly.
    Text in Illustration 
    *1
    One-way Clutch Assembly
    *2
    Outer Race Retainer
    *3
    Planetary Ring Gear

  1. Remove the outer race retainer from the one-way clutch assembly.



55. REMOVE PLANETARY RING GEAR FLANGE


    C136480E02
  1. Using a screwdriver, remove the snap ring from the planetary ring gear.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Planetary Ring Gear Flange
    *3
    Planetary Ring Gear

  1. Remove the planetary ring gear flange from the planetary ring gear.



56. REMOVE NO. 2 BRAKE DISC


    C141524
  1. Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.



    C136483E02
  1. Remove the No. 2 brake flange, 5 No. 2 brake discs and 5 No. 2 brake plates from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    No. 2 Brake Flange
    *2
    No. 2 Brake Plate
    *3
    No. 2 Brake Disc



57. INSPECT NO. 2 BRAKE DISC


    C137438
  1. Check if the contact surfaces of the No. 2 brake discs, No. 2 brake plates and No. 2 brake flange are worn or burnt.

    NOTICE:
    1. If the lining of any No. 2 brake disc is peeled off or discolored, or even if part of the groove is damaged, replace all No. 2 brake discs.
    2. Before assembling new No. 2 brake discs, soak them in ATF for at least 15 minutes.

    If necessary, replace them.



58. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    C136482
  1. Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.



    C136484
  1. Remove the 1st and reverse brake return spring sub-assembly from the transaxle case sub-assembly.



59. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


C141533
  1. Using a vernier caliper, measure the free length of the 1st and reverse brake return spring sub-assembly including the spring seat.

    Standard Free Length:
    15.79 mm (0.621 in.)

    If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.



60. REMOVE NO. 2 BRAKE PISTON


    C136485
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the ATF hole to remove the No. 2 brake piston from the transaxle case sub-assembly.



    C136673E03
  1. Using a screwdriver, remove the 2 O-rings from the No. 2 brake piston.
    Text in Illustration 
    *1
    O-ring



61. REMOVE FRONT PLANETARY GEAR ASSEMBLY


    C136674E01
  1. Using SST and a press, remove the front planetary gear assembly from the transaxle case sub-assembly.

    SST
    09950-60010   (09951-00580)
    09950-70010   (09951-07100)



62. INSPECT FRONT PLANETARY GEAR ASSEMBLY


    C137433E01
  1. Using a feeler gauge, measure the clearance between the front planetary gear case and each pinion gear at points (A) and (B).

    Standard Clearance:
    Point (A):
    0.23 to 0.59 mm (0.00906 to 0.0232 in.)
    Point (B):
    0.16 to 0.66 mm (0.00630 to 0.0259 in.)

    If the clearance is greater than the standard clearance, replace the front planetary gear assembly.



63. REMOVE COUNTER DRIVE GEAR

NOTICE:
Perform this procedure only when the counter drive gear bearing or transaxle case sub-assembly is replaced.



    C194893E01
  1. Using SST and a press, remove the counter drive gear and bearing inner race (rear side) from the transaxle case sub-assembly.

    SST
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)



    C295183
  1. As shown in the illustration, tighten 3 service bolts evenly to make a clearance of approximately 20.0 mm (0.787 in.) between the counter drive gear and bearing inner race (front side).



    C194894E03
  1. Using SST, remove the bearing inner race (front side) from the counter drive gear.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-00020  
    09950-00030  
    09950-60020   (09951-00710)



64. REMOVE NO. 3 BRAKE PISTON


    C325085
  1. Using a screwdriver, remove the snap ring from the transaxle case sub-assembly.



    C320813E01
  1. Remove the brake piston return spring from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Brake Piston Return Spring
    *2
    No. 3 Brake Piston

  1. Remove the No. 3 brake piston from the transaxle case sub-assembly.



65. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY


    C201354
  1. Remove the bolt, cover and manual detent spring sub-assembly from the transaxle case sub-assembly.



66. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    C289567
  1. Remove the parking lock rod sub-assembly from the manual valve lever shaft sub-assembly.

    HINT:
    Align the protrusions with the notches on the manual valve lever shaft sub-assembly to remove the parking lock rod sub-assembly.



67. REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY


    C201356
  1. Using needle-nose pliers, remove the manual valve lever shaft retainer spring from the manual valve lever shaft sub-assembly.



    C288352
  1. Remove the manual valve lever shaft sub-assembly from the transaxle case sub-assembly.



68. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    C136684
  1. Using a screwdriver, remove the manual valve lever shaft oil seal from the transaxle case sub-assembly.