Home › Drivetrain ยท U761E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY


    C296954
  1. Using a screwdriver with its tip wrapped with protective tape, remove the transmission breather hose sub-assembly from the transaxle case sub-assembly.



    C134952E04
  1. Using a screwdriver with its tip wrapped with protective tape, remove the No. 1 breather plug from the breather plug hose.
    Text in Illustration 
    *1
    No. 1 Breather Plug
    *2
    Breather Plug Hose
    *3
    No. 2 Breather Plug
    *4
    O-ring

  1. Using a screwdriver with its tip wrapped with protective tape, remove the No. 2 breather plug from the breather plug hose.

  1. Using a screwdriver with its tip wrapped with protective tape, remove the O-ring from the No. 2 breather plug.



2. REMOVE TRANSMISSION CONTROL SHAFT LEVER


    C136685
  1. Remove the nut, washer and transmission control shaft lever from the manual valve lever shaft sub-assembly.



3. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C136686
  1. Remove the 2 bolts and park/neutral position switch assembly from the transaxle case sub-assembly.

    NOTICE:
    Before removing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to remove the park/neutral position switch assembly straight along the manual valve lever shaft sub-assembly while being careful not to deform the plate spring that supports the manual valve lever shaft sub-assembly. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.



4. REMOVE OIL COOLER UNION SUB-ASSEMBLY


    C317905E01
  1. Remove the union bolt and 2 gaskets from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Union Bolt
    *2
    Gasket

  1. Remove the bolt and oil cooler union sub-assembly from the transaxle case sub-assembly.



5. REMOVE OIL COOLER INLET ELBOW


    C317142
  1. Remove the oil cooler inlet elbow from the transaxle case sub-assembly.

  1. Remove the O-ring from the oil cooler inlet elbow.



6. REMOVE NO. 1 TRANSAXLE CASE PLUG


    C317144
  1. Remove the 3 No. 1 transaxle case plugs from the transaxle case sub-assembly.

  1. Using a screwdriver with its tip wrapped with protective tape, remove the 3 O-rings from the 3 No. 1 transaxle case plugs.



7. REMOVE NO. 2 TRANSAXLE CASE PLUG


    C317145
  1. Using a 6 mm hexagon socket wrench, remove the 3 No. 2 transaxle case plugs from the transaxle housing.

  1. Remove the 3 gaskets from the 3 No. 2 transaxle case plugs.



8. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY


    C317146E01
  1. Support the automatic transaxle assembly with wooden blocks.
    Text in Illustration 
    *a
    Wooden Block



9. REMOVE OVERFLOW PLUG


    C317147
  1. Using a 6 mm hexagon socket wrench, remove the overflow plug from the automatic transaxle oil pan sub-assembly.

  1. Remove the gasket from the overflow plug.



10. REMOVE NO. 1 TRANSMISSION OIL FILLER TUBE


    C317148
  1. Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle oil pan sub-assembly.



11. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    C317149
  1. Remove the 19 bolts and automatic transaxle oil pan sub-assembly from the transaxle case sub-assembly.

    NOTICE:
    Some fluid will remain in the automatic transaxle oil pan sub-assembly. Remove all of the bolts and carefully remove the automatic transaxle oil pan sub-assembly.



12. REMOVE AUTOMATIC TRANSAXLE OIL PAN GASKET
  1. Remove the automatic transaxle oil pan gasket from the automatic transaxle oil pan sub-assembly.



13. REMOVE TRANSMISSION OIL CLEANER MAGNET


    C317150E01
  1. Remove the 4 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.
    Text in Illustration 
    *1
    Transmission Oil Cleaner Magnet



14. INSPECT TRANSMISSION OIL CLEANER MAGNET


    C138722
  1. Use the removed transmission oil cleaner magnets to collect any steel chips. Examine the chips and particles in the automatic transaxle oil pan sub-assembly and on the transmission oil cleaner magnets to determine what type of wear might be found in the automatic transaxle assembly.
    Result 
    Steel (magnetic)
    Brass (non-magnetic)
    Bearing, gear and plate wear
    Bushing wear



15. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


    C201702
  1. Remove the 2 bolts and valve body oil strainer assembly from the transmission valve body assembly.



    C317151E01
  1. Remove the O-ring from the valve body oil strainer assembly.
    Text in Illustration 
    *1
    O-ring



16. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    C201704
  1. Remove the 11 bolts and transmission valve body assembly from the transaxle case sub-assembly.

    NOTICE:
    When removing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case sub-assembly to interfere with each other.



17. REMOVE TRANSAXLE CASE GASKET


    C201316
  1. Remove the 2 transaxle case gaskets from the transaxle case sub-assembly.



18. INSPECT INPUT SHAFT SUB-ASSEMBLY END PLAY


    C136696
  1. Using a dial indicator, measure the input shaft sub-assembly end play.

    Standard End Play:
    0.020 to 1.242 mm (0.000787 to 0.0489 in.)



19. REMOVE REFILL PLUG


    C136430
  1. Remove the refill plug from the rear transaxle cover sub-assembly.

  1. Remove the gasket from the refill plug.



20. REMOVE REAR TRANSAXLE COVER PLUG


    C201317
  1. Remove the 3 rear transaxle cover plugs from the rear transaxle cover sub-assembly.

  1. Using a screwdriver with its tip wrapped with protective tape, remove the 3 O-rings from the 3 rear transaxle cover plugs.



21. REMOVE REAR TRANSAXLE COVER SUB-ASSEMBLY


    C274845
  1. Remove the 14 bolts from the rear transaxle cover sub-assembly.

  1. Using a brass bar and a hammer, tap on the circumference of the rear transaxle cover sub-assembly to remove the rear transaxle cover sub-assembly from the transaxle case sub-assembly.



    C274807
  1. Using a screwdriver with its tip wrapped with protective tape, remove the 3 O-rings from the transaxle case sub-assembly.



    C297890E01
  1. Remove the thrust needle roller bearing and thrust bearing race from the rear transaxle cover sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Bearing Race



    C299131E01
  1. Using a screwdriver with its tip wrapped with protective tape, remove the 2 oil seal rings from the rear transaxle cover sub-assembly.
    Text in Illustration 
    *1
    Oil Seal Ring



    C201318
  1. Using a T30 "TORX" socket wrench, remove the 2 "TORX" screws and rear transaxle cover plate from the rear transaxle cover sub-assembly.



    C194888E03
  1. Using SST, remove the needle roller bearing from the rear transaxle cover sub-assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09319-60020  



22. REMOVE REAR MULTIPLE DISC CLUTCH ASSEMBLY


    C202901E02
  1. Remove the rear multiple disc clutch assembly from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Rear Multiple Disc Clutch Assembly

  1. Remove the thrust needle roller bearing from the transaxle case sub-assembly.



    C224456E01
  1. Using a screwdriver with its tip wrapped with protective tape, remove the O-ring from the rear multiple disc clutch assembly.
    Text in Illustration 
    *1
    O-ring
    *2
    Oil Seal Ring

  1. Using a screwdriver with its tip wrapped with protective tape, remove the oil seal ring from the rear multiple disc clutch assembly.



23. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


    C317752E01
  1. Using 2 screwdrivers with their tips wrapped with protective tape and a hammer, remove the snap ring from the rear multiple disc clutch assembly.
    Text in Illustration 
    *1
    Snap Ring
    *a
    Protective Tape

    HINT:
    Use a piece of cloth to keep the snap ring from flying off.



    C201321E02
  1. Remove the rear planetary sun gear assembly from the rear multiple disc clutch assembly.
    Text in Illustration 
    *1
    Rear Planetary Sun Gear Assembly



    C201526E02
  1. Remove the thrust needle roller bearing and thrust bearing race from the rear multiple disc clutch assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Bearing Race



24. INSPECT REAR PLANETARY SUN GEAR ASSEMBLY


    C201528
  1. Using a caliper gauge, measure the inside diameter of the bushing of the rear planetary sun gear assembly.

    Standard Inside Diameter:
    25.580 to 25.601 mm (1.00708 to 1.00791 in.)

    Maximum Inside Diameter:
    25.601 mm (1.00791 in.)

    If the inside diameter is greater than the maximum, replace the rear planetary sun gear assembly.



25. REMOVE TRANSAXLE HOUSING


    C205232
  1. Remove the 20 bolts from the transaxle housing.

  1. Using a brass bar and a hammer, tap on the circumference of the transaxle housing to remove the transaxle housing from the transaxle case sub-assembly.



26. REMOVE DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING RH (OUTER RACE)


    C201323E01
  1. Using SST, remove the differential drive pinion tapered roller bearing RH (outer race) and shim from the transaxle housing.

    SST
    09308-00010  



27. REMOVE FRONT DRIVE SHAFT OIL SEAL RH


    C201325E01
  1. Using SST and a hammer, remove the front drive shaft oil seal RH from the transaxle housing.

    SST
    09950-60010   (09951-00550)
    09950-70010   (09951-07200)



28. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE)


    C201324E03
  1. Using SST, remove the front differential case front tapered roller bearing (outer race) and shim from the transaxle housing.

    SST
    09308-00010  



29. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


    C201326
  1. Remove the bolt, clamp and differential gear lube apply tube from the transaxle housing.



30. REMOVE TRANSAXLE HOUSING OIL SEPARATOR


    C201327
  1. Remove the 3 bolts and transaxle housing oil separator from the transaxle housing.



31. REMOVE FRONT OIL PUMP ASSEMBLY


    C201328E02
  1. Remove the gasket from the front oil pump assembly.
    Text in Illustration 
    *1
    Gasket

  1. Remove the 7 bolts and front oil pump assembly from the transaxle case sub-assembly.



    C201329
  1. Remove the front oil pump body O-ring from the front oil pump body sub-assembly.



    C293929E01
  1. Remove the thrust bearing race from the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race



    C293927E01
  1. Remove the thrust needle roller bearing from the counter drive gear nut.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    O-ring

  1. Remove the O-ring from the transaxle case sub-assembly.



32. REMOVE NO. 3 BRAKE DISC


    C317753E02
  1. Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the front oil pump assembly.
    Text in Illustration 
    *a
    Protective Tape



    C317152E01
  1. Remove the 2 No. 3 brake flanges, 3 No. 3 brake discs and 2 No. 3 brake plates from the front oil pump assembly.
    Text in Illustration 
    *1
    No. 3 Brake Flange
    *2
    No. 3 Brake Plate
    *3
    No. 3 Brake Disc



33. INSPECT NO. 3 BRAKE DISC


    C317139
  1. Check if the contact surfaces of the No. 3 brake discs, No. 3 brake plates and No. 3 brake flanges are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 3 brake disc is peeled off or discolored, or even if part of the groove is damaged, replace all of the No. 3 brake discs.
    2. Before installing new No. 3 brake discs, soak them in ATF for at least 15 minutes.



34. REMOVE AND INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY


    C293913
  1. Remove the underdrive planetary gear assembly from the front oil pump assembly.



35. REMOVE NO. 3 BRAKE HUB


    C136454
  1. Remove the No. 3 brake hub from the underdrive planetary gear assembly.



    C202906E02
  1. Remove the thrust needle roller bearing and thrust bearing race from the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race
    *2
    Thrust Needle Roller Bearing



36. REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY


    C201331E02
  1. While expanding the snap ring with a snap ring expander, remove the planetary sun gear sub-assembly from the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Planetary Sun Gear Sub-assembly
    *2
    Underdrive Planetary Gear Assembly
    *3
    Snap Ring

  1. Remove the snap ring from the underdrive planetary gear assembly.



37. INSPECT UNDERDRIVE PLANETARY GEAR ASSEMBLY


    C200900
  1. Using a feeler gauge, measure the clearance between the underdrive planetary gear case and each pinion gear.

    Standard Clearance:
    0.18 to 0.54 mm (0.00709 to 0.0213 in.)

    If the clearance is not as specified, replace the underdrive planetary gear assembly.



38. INSPECT PLANETARY SUN GEAR SUB-ASSEMBLY


    C138259
  1. Using a caliper gauge, measure the inside diameters of the bushings of the planetary sun gear sub-assembly.

    Standard Inside Diameter:
    25.525 to 25.546 mm (1.00492 to 1.00575 in.)

    Maximum Inside Diameter:
    25.546 mm (1.00575 in.)

    If the inside diameter is greater than the maximum, replace the planetary sun gear sub-assembly.



39. REMOVE INPUT SHAFT SUB-ASSEMBLY


    C293914
  1. Remove the input shaft sub-assembly from the front oil pump assembly.



    C202905E02
  1. Remove the thrust needle roller bearing and thrust bearing race from the input shaft sub-assembly.
    Text in Illustration 
    *1
    Thrust Bearing Race
    *2
    Thrust Needle Roller Bearing
    *3
    Input Shaft Sub-assembly
    *4
    Oil Seal Ring

  1. Using a screwdriver with its tip wrapped with protective tape, remove the 3 oil seal rings from the input shaft sub-assembly.



40. REMOVE UNDERDRIVE PLANETARY SUN GEAR


    C293915E01
  1. Remove the underdrive planetary sun gear from the front oil pump assembly.
    Text in Illustration 
    *1
    Underdrive Planetary Sun Gear
    *2
    Thrust Needle Roller Bearing

  1. Remove the thrust needle roller bearing from the front oil pump assembly.



41. REMOVE NO. 1 BRAKE DISC


    C293916E01
  1. Using a screwdriver with its tip wrapped with protective tape, remove the 2 snap rings and brake snap ring stopper from the front oil pump assembly.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Brake Snap Ring Stopper



    C317153E01
  1. Remove the No. 1 brake flange, 3 No. 1 brake discs and 3 No. 1 brake plates from the front oil pump assembly.
    Text in Illustration 
    *1
    No. 1 Brake Flange
    *2
    No. 1 Brake Plate
    *3
    No. 1 Brake Disc



42. INSPECT NO. 1 BRAKE DISC


    C317139
  1. Check if the contact surfaces of the No. 1 brake discs, No. 1 brake plates and No. 1 brake flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 1 brake disc is peeled off or discolored, or even if part of the groove is damaged, replace all of the No. 1 brake discs.
    2. Before installing new No. 1 brake discs, soak them in ATF for at least 15 minutes.



43. REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C293918
  1. Remove the 3 2nd brake piston return spring sub-assemblies from the front oil pump assembly.



44. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C138254
  1. Using a vernier caliper, measure the free length of the 3 2nd brake piston return spring sub-assemblies including the spring seats.

    Standard Free Length:
    23.26 mm (0.916 in.)

    If the free length is shorter than the standard free length, replace the 2nd brake piston return spring sub-assembly.



45. REMOVE NO. 1 BRAKE PISTON


    C293919
  1. While holding the front oil pump assembly by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the front oil pump assembly to remove the No. 1 brake piston.



    C319480E01
  1. Using a screwdriver with its tip wrapped with protective tape, remove the 2 O-rings from the No. 1 brake piston.
    Text in Illustration 
    *1
    O-ring



46. REMOVE FRONT DIFFERENTIAL CASE


    C201332
  1. Remove the front differential case from the transaxle case sub-assembly.



47. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE)


    C317736E02
  1. Using SST, remove the front differential case rear tapered roller bearing (inner race) from the front differential case.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00480)



48. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE)


    C317735E02
  1. Using SST, remove the front differential case front tapered roller bearing (inner race) from the front differential case.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00480)



49. REMOVE COUNTER DRIVE GEAR NUT


    C201333E01
  1. Using SST and a hammer, release the staked part of the front planetary gear assembly.

    SST
    09930-00010  



    C299140E01
  1. Turn the manual valve lever shaft sub-assembly counterclockwise to set it to the P position as shown in the illustration.



    C201527E01
  1. Using SST, remove the counter drive gear nut from the front planetary gear assembly.

    SST
    09387-00130  



    C299141E01
  1. Turn the manual valve lever shaft sub-assembly 2 notches clockwise to set it to the N position as shown in the illustration.



50. REMOVE COUNTER DRIVEN GEAR


    C201336
  1. Remove the counter driven gear from the transaxle case sub-assembly.



51. REMOVE DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING RH (INNER RACE)


    C324774E01
  1. Using SST, remove the differential drive pinion tapered roller bearing RH (inner race) from the counter driven gear.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00320)



52. REMOVE DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING LH (INNER RACE)

HINT:
If removing the differential drive pinion tapered roller bearing LH (inner race), replace the counter driven gear with a new one.



53. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE)


    C317737E01
  1. Using SST, remove the front differential case rear tapered roller bearing (outer race) from the transaxle case sub-assembly.

    SST
    09308-00010  



54. REMOVE PAWL SHAFT CLAMP


    C201339
  1. Remove the bolt and pawl shaft clamp from the transaxle case sub-assembly.



55. REMOVE NO. 1 TRANSMISSION CASE PLATE


    C201340
  1. Remove the bolt and No. 1 transmission case plate from the transaxle case sub-assembly.



56. REMOVE PAWL STOPPER PLATE


    C201341
  1. Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.



57. REMOVE PARKING LOCK SLEEVE


    C201342
  1. Remove the parking lock sleeve from the transaxle case sub-assembly.



58. REMOVE PARKING LOCK PAWL


    C201343E02
  1. Remove the spring, parking lock pawl pin, parking lock pawl shaft and parking lock pawl from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Parking Lock Pawl Pin
    *2
    Parking Lock Pawl Shaft
    *3
    Spring
    *4
    Parking Lock Pawl



59. REMOVE DIFFERENTIAL DRIVE PINION TAPERED ROLLER BEARING LH (OUTER RACE)


    C201344E01
  1. Using SST, remove the differential drive pinion tapered roller bearing LH (outer race) from the transaxle case sub-assembly.

    SST
    09308-00010  



60. REMOVE FRONT DRIVE SHAFT OIL SEAL LH


    C138709E01
  1. Using SST and a hammer, remove the front drive shaft oil seal LH from the transaxle case sub-assembly.

    SST
    09950-60010   (09951-00650)
    09950-70010   (09951-07100)



61. REMOVE ONE-WAY CLUTCH ASSEMBLY


    C317754E01
  1. Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.
    Text in Illustration 
    *a
    Protective Tape



    C141526E02
  1. Remove the one-way clutch assembly with planetary ring gear from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    One-way Clutch Assembly with Planetary Ring Gear
    *2
    Thrust Needle Roller Bearing

  1. Remove the thrust needle roller bearing from the front planetary gear assembly.



    C201345E02
  1. Remove the one-way clutch assembly from the planetary ring gear.
    Text in Illustration 
    *1
    One-way Clutch Assembly
    *2
    Outer Race Retainer
    *3
    Planetary Ring Gear

  1. Remove the outer race retainer from the one-way clutch assembly.



62. INSPECT ONE-WAY CLUTCH ASSEMBLY


    C189425E04
  1. Temporarily install the one-way clutch assembly to the planetary ring gear.
    Text in Illustration 
    *1
    Planetary Ring Gear
    *2
    One-way Clutch Assembly
    *a
    Free
    *b
    Lock

  1. Make sure that the one-way clutch assembly turns freely counterclockwise and locks when turned clockwise.
    If the one-way clutch assembly does not operate normally, replace it.



63. REMOVE PLANETARY RING GEAR FLANGE


    C136480E02
  1. Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the planetary ring gear.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Planetary Ring Gear Flange
    *3
    Planetary Ring Gear

  1. Remove the planetary ring gear flange from the planetary ring gear.



64. REMOVE NO. 2 BRAKE DISC


    C317755E01
  1. Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.
    Text in Illustration 
    *a
    Protective Tape



    C238853E01
  1. Remove the No. 2 brake flange, 4 No. 2 brake discs and 4 No. 2 brake plates from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    No. 2 Brake Flange
    *2
    No. 2 Brake Plate
    *3
    No. 2 Brake Disc



65. INSPECT NO. 2 BRAKE DISC


    C317140
  1. Check if the contact surfaces of the No. 2 brake discs, No. 2 brake plates and No. 2 brake flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of any No. 2 brake disc is peeled off or discolored, or even if part of the groove is damaged, replace all of the No. 2 brake discs.
    2. Before installing new No. 2 brake discs, soak them in ATF for at least 15 minutes.



66. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    C317756E01
  1. Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.
    Text in Illustration 
    *a
    Protective Tape



    C136484
  1. Remove the 1st and reverse brake return spring sub-assembly from the transaxle case sub-assembly.



67. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    C141533
  1. Using a vernier caliper, measure the free length of the 1st and reverse brake return spring sub-assembly including the spring seat.

    Standard Free Length:
    15.79 mm (0.622 in.)

    If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.



68. REMOVE NO. 2 BRAKE PISTON


    C136485
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole to remove the No. 2 brake piston from the transaxle case sub-assembly.



    C319481E01
  1. Using a screwdriver with its tip wrapped with protective tape, remove the 2 O-rings from the No. 2 brake piston.
    Text in Illustration 
    *1
    O-ring



69. REMOVE FRONT PLANETARY GEAR ASSEMBLY


    C136674E01
  1. Using SST and a press, remove the front planetary gear assembly from the transaxle case sub-assembly.

    SST
    09950-60010   (09951-00580)
    09950-70010   (09951-07100)



70. REMOVE COUNTER DRIVE GEAR


    C293937E01
  1. Using SST and a press, remove the counter drive gear with counter drive gear bearing inner race (front side) from the transaxle case sub-assembly.

    SST
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)

  1. Remove the counter drive gear bearing inner race (rear side).

  1. Remove the 2 counter drive gear bearings (balls and cage) from the counter drive gear bearing (outer race).



    C201348
  1. As shown in the illustration, tighten 2 service bolts evenly to make a clearance of approximately 5.0 mm (0.197 in.) between the counter drive gear and counter drive gear bearing inner race (front side).



    C201349E04
  1. Using SST, remove the counter drive gear bearing inner race (front side) from the counter drive gear.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-00020  
    09950-00030  
    09950-60020   (09951-00710)



71. REMOVE NO. 3 BRAKE PISTON


    C201350E01
  1. Place SST on the No. 3 brake piston return spring sub-assembly and compress the No. 3 brake piston return spring sub-assembly with a press.

    SST
    09387-00070  

  1. Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.



    C317911E01
  1. Remove the No. 3 brake piston return spring sub-assembly from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    No. 3 Brake Piston Return Spring Sub-assembly



    C317912E01
  1. Remove the No. 3 brake piston from the transaxle case sub-assembly.
    Text in Illustration 
    *1
    No. 3 Brake Piston



    C319482E01
  1. Using a screwdriver with its tip wrapped with protective tape, remove the 2 O-rings from the No. 3 brake piston.
    Text in Illustration 
    *1
    O-ring



72. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C201505
  1. Using a vernier caliper, measure the free length of the No. 3 brake piston return spring sub-assembly including the spring seat.

    Standard Free Length:
    9.15 mm (0.360 in.)

    If the free length is shorter than the standard free length, replace the No. 3 brake piston return spring sub-assembly.



73. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY


    C201354
  1. Remove the bolt, manual detent spring cover and manual detent spring sub-assembly from the transaxle case sub-assembly.



74. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    C201355
  1. Remove the parking lock rod sub-assembly from the manual valve lever shaft sub-assembly.

    HINT:
    Align the protrusions with the notches on the manual valve lever shaft sub-assembly to remove the parking lock rod sub-assembly.



75. REMOVE MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY


    C201356
  1. Using needle-nose pliers, remove the manual valve lever shaft retainer spring from the manual valve lever shaft sub-assembly.



    C288352
  1. Remove the manual valve lever shaft sub-assembly from the transaxle case sub-assembly.



76. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    C317757E01
  1. Using a screwdriver with its tip wrapped with protective tape, remove the manual valve lever shaft oil seal from the transaxle case sub-assembly.
    Text in Illustration 
    *a
    Protective Tape