Home › Drivetrain ยท U660E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > REASSEMBLY

for Preparation Click here



1. BEARING POSITION


  1. Check each bearing position and installation direction.


    C320818E01



    C297115E01


    Mark
    Front Race Diameter
    Inside / Outside mm (in.)
    Thrust Bearing Diameter
    Inside / Outside mm (in.)
    Rear Race Diameter
    Inside / Outside mm (in.)
    A
    -
    57.7 (2.27) / 75.2 (2.96)
    -
    B
    -
    29.1 (1.15) / 48.6 (1.91)
    30.7 (1.21) / 48.3 (1.90)
    C
    -
    62.6 (2.47) / 82.4 (3.24)
    65.9 (2.59) / 80.3 (3.16)
    D
    59.4 (2.34) / 77 (3.03)
    53.1 (2.09) / 79 (3.11)
    -
    E
    -
    56.1 (2.21) / 80.9 (3.19)
    -
    F
    -
    61.2 (2.41) / 79 (3.11)
    -
    G
    -
    28 (1.10) / 47.1 (1.85)
    26.1 (1.03) / 44 (1.73)
    H
    52.2 (2.06) / 70.4 (2.77)
    48.9 (1.93) / 72.0 (2.84)
    -



2. INSTALL COUNTER DRIVE GEAR BEARING

NOTICE:
Perform this procedure only when replacement of the counter drive gear bearing or transaxle case sub-assembly is necessary.



    C138721E01
  1. Using SST and a press, install a new counter drive gear bearing (outer race) and a new snap ring to the transaxle case sub-assembly.

    SST
    09950-60020   (09951-01030)
    09950-70010   (09951-07100)



3. INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE


    C325095E01
  1. Using SST and a hammer, install a new counter driven gear rear tapered roller bearing outer race to the transaxle case sub-assembly.

    SST
    09950-60010   (09951-00650)
    09950-70010   (09951-07100)

    NOTICE:
    Make sure to install the counter driven gear rear tapered roller bearing outer race so that there is no clearance between the counter driven gear rear tapered roller bearing outer race and transaxle case sub-assembly. If there is any clearance, the turning torque of the counter driven gear cannot be measured correctly.



4. INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE


    C194900E01
  1. Install the shim to the transaxle housing.

  1. Using SST, install a new counter driven gear front tapered roller bearing outer race to the transaxle housing.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07100)

    NOTICE:
    Make sure to install the counter driven gear front tapered roller bearing outer race so that there is no clearance between the counter driven gear front tapered roller bearing outer race, shim and transaxle housing. If there is any clearance, the turning torque of the counter driven gear cannot be measured correctly.



5. INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING


    C194897E01
  1. Using SST and a press, install a new counter driven gear rear tapered roller bearing to the counter driven gear.

    SST
    09950-60010   (09951-00420)

    NOTICE:
    Make sure to install the counter driven gear rear tapered roller bearing so that there is no clearance between the counter driven gear rear tapered roller bearing and counter driven gear. If there is any clearance, the turning torque of the counter driven gear cannot be measured correctly.



6. INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING


    C194896E01
  1. Using SST and a press, install a new counter driven gear front tapered roller bearing to the counter driven gear.

    SST
    09950-60010   (09951-00530)

    NOTICE:
    Make sure to install the counter driven gear front tapered roller bearing so that there is no clearance between the counter driven gear front tapered roller bearing and counter driven gear. If there is any clearance, the turning torque of the counter driven gear cannot be measured correctly.



7. ADJUST COUNTER DRIVEN GEAR PRELOAD
  1. Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.



    C317767
  1. Install the counter driven gear to the transaxle case sub-assembly.



    C317768
  1. Install the front differential case to the transaxle case sub-assembly.



    C136447E02
  1. Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

    Torque:
    Bolt (A):
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }
    Bolt (B):
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



    C317726E01
  1. Using SST and a torque wrench, measure the turning torque of the counter driven gear while rotating SST at 10 rpm.

    SST
    09564-33010  

    Turning Torque:
    Differential side bearing preload + 2.2 to 4.1 N*m (22 to 42 kgf*cm, 19 to 36 in.*lbf)

    If the turning torque is not within the specified range, refer to the table below to select a shim for the counter driven gear front tapered roller bearing outer race so that the turning torque is within the specified range.
    Shim Thickness: mm (in.) 
    Thickness
    Thickness
    Thickness
    Thickness
    2.000 (0.0787)
    2.275 (0.0896)
    2.525 (0.0994)
    2.775 (0.109)
    2.025 (0.0797)
    2.300 (0.0906)
    2.550 (0.100)
    2.800 (0.110)
    2.050 (0.0807)
    2.325 (0.0915)
    2.575 (0.101)
    2.825 (0.111)
    2.075 (0.0817)
    2.350 (0.0925)
    2.600 (0.102)
    2.850 (0.112)
    2.100 (0.0827)
    2.375 (0.0935)
    2.625 (0.103)
    2.875 (0.113)
    2.125 (0.0837)
    2.400 (0.0945)
    2.650 (0.104)
    2.900 (0.114)
    2.150 (0.0846)
    2.425 (0.0955)
    2.675 (0.105)
    2.925 (0.115)
    2.175 (0.0856)
    2.450 (0.0965)
    2.700 (0.106)
    2.950 (0.116)
    2.200 (0.0866)
    2.475 (0.0974)
    2.725 (0.107)
    2.975 (0.117)
    2.225 (0.0876)
    2.500 (0.0984)
    2.750 (0.108)
    3.000 (0.118)
    2.250 (0.0886)
    -
    -
    -

  1. Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.

  1. Remove the front differential case from the transaxle case sub-assembly.

  1. Remove the counter driven gear from the transaxle case sub-assembly.



8. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL


    C188148E01
  1. Coat the lip of a new manual valve lever shaft oil seal with MP grease.

  1. Using SST and a hammer, install the manual valve lever shaft oil seal to the transaxle case sub-assembly.

    SST
    09950-60010   (09951-00230)
    09950-70010   (09951-07100)

    Standard Depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



9. INSTALL MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY


    C288518
  1. Install the manual valve lever shaft sub-assembly to the transaxle case sub-assembly.

    NOTICE:
    Do not damage the manual valve lever shaft oil seal while installing the manual valve lever shaft sub-assembly to the transaxle case sub-assembly.



    C201356
  1. Using needle-nose pliers, install the manual valve lever shaft retainer spring to the manual valve lever shaft sub-assembly.



10. INSTALL PARKING LOCK ROD SUB-ASSEMBLY


    C289567
  1. Align the protrusions with the notches on the manual valve lever shaft sub-assembly and install the parking lock rod sub-assembly.



11. INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY


    C201354
  1. Install the manual detent spring sub-assembly and cover to the transaxle case sub-assembly with the bolt.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    NOTICE:
    Make sure to install the manual detent spring sub-assembly first and then the cover.



12. INSTALL NO. 3 BRAKE PISTON


    C320820
  1. Coat the lip of the No. 3 brake piston with ATF.



    C320821
  1. Temporarily install the No. 3 brake piston to the transaxle case sub-assembly.



    C320822
  1. Temporarily install the pawl stopper plate to the transaxle case sub-assembly with the 2 bolts.

    NOTICE:
    After installing, make sure that the protrusions on the No. 3 brake piston and grooves on the pawl stopper plate are aligned.



    C320823E01
  1. Press the No. 3 brake piston into the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Brake Piston Return Spring
    *2
    No. 3 Brake Piston
    *3
    Pawl Stopper Plate

    NOTICE:
    Make sure that the lip of the No. 3 brake piston is not twisted and does not get caught in the transaxle case sub-assembly.

    HINT:
    Use the installation surface of the brake piston return spring to press the No. 3 brake piston into the transaxle case sub-assembly.

  1. Install the brake piston return spring to the transaxle case sub-assembly.

    NOTICE:
    Install the brake piston return spring as shown in the illustration.



    C325086
  1. Remove the 2 bolts and pawl stopper plate from the transaxle case sub-assembly.



    C320824E01
  1. Place SST on the brake piston return spring and compress the brake piston return spring using a press.
    Text in Illustration 
    *1
    Snap Ring

    SST
    09387-00070  

    NOTICE:
    Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.

  1. Using a screwdriver, install the snap ring to the transaxle case sub-assembly as shown in the illustration.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.
    2. Be sure to orient the snap ring so that the edges do not protrude into one of the cutouts on the brake piston return spring as shown in the illustration.



13. INSTALL COUNTER DRIVE GEAR
  1. Install 2 new balls of the counter drive gear bearing to the counter drive gear bearing.



    C137424E01
  1. Using SST, install the counter drive gear, a new bearing inner race (front side) and bearing inner race (rear side) to the transaxle case sub-assembly.

    SST
    09223-15030  
    09527-17011  09950-60020   (09951-00810)
    09950-70010   (09951-07100)

    NOTICE:
    There should not be any clearance between the bearing inner race (front side) and counter drive gear.



14. INSTALL FRONT PLANETARY GEAR ASSEMBLY


    C137425E01
  1. Using SST and a press, install the front planetary gear assembly to the transaxle case sub-assembly.

    SST
    09223-15030  
    09527-17011  
    09951-01100  



15. INSTALL NO. 2 BRAKE PISTON


    C136673E03
  1. Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Ensure that the O-rings are not twisted.



    C138726
  1. Install the No. 2 brake piston to the transaxle case sub-assembly.

    NOTICE:
    Be careful not to damage the O-rings.



16. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
  1. Install the 1st and reverse brake return spring sub-assembly to the transaxle case sub-assembly.



    C137434E01
  1. Place SST on the 1st and reverse brake return spring sub-assembly and compress the 1st and reverse brake return spring sub-assembly using a press.

    SST
    09387-00060  

    NOTICE:
    Stop the press when the 1st and reverse brake return spring sub-assembly is flush with the snap ring groove. This prevents the 1st and reverse brake return spring sub-assembly from being deformed.

  1. Using a screwdriver, install the snap ring to the transaxle case sub-assembly as shown in the illustration.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.
    2. Be sure to orient the snap ring so that the edges do not protrude into one of the cutouts on the transaxle case sub-assembly as shown in the illustration.



17. INSTALL NO. 2 BRAKE DISC


    C136483E02
  1. Install the 5 No. 2 brake discs, 5 No. 2 brake plates and No. 2 brake flange to the transaxle case sub-assembly.
    Text in Illustration 
    *1
    No. 2 Brake Flange
    *2
    No. 2 Brake Plate
    *3
    No. 2 Brake Disc

    NOTICE:
    Make sure that the No. 2 brake discs, No. 2 brake plates and No. 2 brake flange are installed in the correct order.



    C136481
  1. Using a screwdriver, install the snap ring to the transaxle case sub-assembly.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.
    2. Be sure to orient the snap ring so that the edges do not protrude into one of the cutouts on the transaxle case sub-assembly as shown in the illustration.



18. INSPECT CLEARANCE OF NO. 2 BRAKE


    C137439E01
  1. Apply compressed air to the oil pressure supply hole shown in the illustration, and check the operation of the No. 2 brake piston.
    Text in Illustration 
    *1
    No. 2 Brake Piston
    *a
    Clearance

  1. Set a dial indicator as shown in the illustration.

  1. Using a dial indicator, measure the clearance of the No. 2 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    Standard Clearance:
    0.884 to 1.196 mm (0.0348 to 0.0471 in.)

    HINT:
    1. Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.
      If the clearance is not as specified, select an appropriate No. 2 brake flange so that the clearance will be within the specified range.
    2. There are 5 No. 2 brake flanges of different thicknesses.

    No. 2 Brake Flange Thickness: mm (in.) 
    Mark
    Thickness
    40
    4.0 (0.157)
    41
    4.1 (0.161)
    42
    4.2 (0.165)
    43
    4.3 (0.169)
    44
    4.4 (0.173)



19. INSTALL PLANETARY RING GEAR FLANGE


    C136480E02
  1. Install the planetary ring gear flange to the planetary ring gear.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Planetary Ring Gear Flange
    *3
    Planetary Ring Gear

  1. Using a screwdriver, install the snap ring to the planetary ring gear.

    NOTICE:
    Confirm that the snap ring is correctly located in the groove of the planetary ring gear.



20. INSTALL PLANETARY RING GEAR


    C299134E01
  1. Install the outer race retainer to the one-way clutch assembly.
    Text in Illustration 
    *1
    One-way Clutch Assembly
    *2
    Outer Race Retainer
    *3
    Planetary Ring Gear

  1. Install the planetary ring gear to the one-way clutch assembly.

    NOTICE:
    Make sure that the one-way clutch assembly is positioned in the correct direction as shown in the illustration.



21. INSTALL ONE-WAY CLUTCH ASSEMBLY


    C297132E01
  1. Coat the thrust needle roller bearing with ATF and install it to the front planetary gear assembly.
    Text in Illustration 
    *1
    One-way Clutch Assembly
    *2
    Outer Race Retainer
    *3
    Transaxle Case Sub-assembly
    Bearing Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    56.1 (2.21)
    80.9 (3.19)

    NOTICE:
    Be sure to install the thrust needle roller bearing so that the temper colored side of the race is visible.

  1. Install the one-way clutch assembly with planetary ring gear to the transaxle case sub-assembly.

    NOTICE:
    1. Make sure that there is no clearance between the outer race retainer and claw on the one-way clutch assembly. If there is any clearance, the spring of the retainer will be deformed.
    2. Ensure that there is no clearance between the one-way clutch assembly and transaxle case sub-assembly.



    C136477
  1. Using a screwdriver, install the snap ring to the transaxle case sub-assembly.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the transaxle case sub-assembly.
    2. Be sure to orient the snap ring so that the edges do not protrude into one of the cutouts on the transaxle case sub-assembly as shown in the illustration.



22. INSTALL PARKING LOCK PAWL


    C136475E02
  1. Install the parking lock pawl to the transaxle case sub-assembly with the parking lock pawl shaft.
    Text in Illustration 
    *1
    Parking Lock Pawl Shaft
    *2
    Parking Lock Pawl
    *3
    Spring
    *4
    Parking Lock Pawl Pin

  1. Install the parking lock pawl pin to the transaxle case sub-assembly.



    C137444
  1. Install the spring to the parking lock pawl.

    NOTICE:
    Make sure that one end of the spring is set in the hole of the transaxle case sub-assembly and the other end is positioned on the parking lock pawl as shown in the illustration.



23. INSTALL PARKING LOCK SLEEVE


    C136474
  1. Install the parking lock sleeve to the transaxle case sub-assembly.



24. INSTALL PAWL STOPPER PLATE


    C136473
  1. Install the pawl stopper plate to the transaxle case sub-assembly with the 2 bolts.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



25. INSTALL PAWL SHAFT CLAMP


    C136472
  1. Install the pawl shaft clamp to the transaxle case sub-assembly with the bolt.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



26. INSTALL COUNTER DRIVEN GEAR


    C136469
  1. Install the counter driven gear to the transaxle case sub-assembly.



27. INSTALL COUNTER DRIVE GEAR NUT


    C299132E01
  1. Turn the manual valve lever shaft sub-assembly 2 notches counterclockwise to set it to the P position as shown in the illustration.



    C202887E01
  1. Using SST, install a new counter drive gear nut to the front planetary gear assembly.

    SST
    09387-00130  

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }



    C299133E01
  1. Turn the manual valve lever shaft sub-assembly 2 notches clockwise to set it to the N position as shown in the illustration.

  1. Remove the counter driven gear from the transaxle case sub-assembly.



    C319474E01
  1. Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm.

    SST
    09387-00130  

    Turning Torque:
    0.1 to 0.2 N*m (1 to 2 kgf*cm, 0.9 to 1.9 in.*lbf)

    If the measured value is not within the specified range, gradually tighten the counter drive gear nut until the turning falls within the specified range.

    Maximum Torque:
    180 N*m (1835 kgf*cm, 133 ft.*lbf)



    C136698E01
  1. Using SST and a hammer, stake the front planetary gear assembly.

    SST
    09930-00010  

  1. Install the counter driven gear to the transaxle case sub-assembly.



28. INSTALL FRONT DIFFERENTIAL CASE


    C136467
  1. Install the front differential case to the transaxle case sub-assembly.



29. INSTALL NO. 1 BRAKE PISTON


    C136466E03
  1. Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Ensure that the O-rings are not twisted.



    C138253
  1. Install the No. 1 brake piston to the front oil pump assembly.

    NOTICE:
    Be careful not to damage the O-rings.



30. INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C136464
  1. Install the 3 2nd brake piston return spring sub-assemblies to the front oil pump assembly.

    NOTICE:
    Make sure that the 3 2nd brake piston return spring sub-assemblies are installed to the protrusions on the front oil pump assembly.



31. INSTALL NO. 1 BRAKE DISC


    C293936E01
  1. Install the 4 No. 1 brake discs, 4 No. 1 brake plates and No. 1 brake flange to the front oil pump assembly.
    Text in Illustration 
    *1
    No. 1 Brake Flange
    *2
    No. 1 Brake Plate
    *3
    No. 1 Brake Disc

    NOTICE:
    1. Make sure that the No. 1 brake discs, No. 1 brake plates, and No. 1 brake flange are installed in the correct order.
    2. Be sure to install the No. 1 brake flange in the correct direction.

  1. Place SST on the No. 1 brake flange and compress the No. 1 brake flange using a press.

    SST
    09387-00070  
    09495-65040  

    NOTICE:
    Stop the press when the 2nd brake piston return spring sub-assemblies are flush with the snap ring groove. This prevents the 2nd brake piston return spring sub-assemblies from being deformed.



    C297700E03
  1. Using a screwdriver, install the snap ring to the front oil pump assembly as shown in the illustration (#1).

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the front oil pump assembly.
    2. Make sure to align the protruding part of the snap ring with the cutout (#1) of the front oil pump assembly shown in the illustration to install the snap ring.



    C176220
  1. Install the brake snap ring stopper to the front oil pump assembly.

    NOTICE:
    Be sure to install the brake snap ring stopper in the correct direction.



    C297701E04
  1. Using a screwdriver, install the snap ring to the front oil pump assembly as shown in the illustration (#2).

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the front oil pump assembly.
    2. Make sure to align the protruding part of the snap ring with the cutout (#2) of the front oil pump assembly shown in the illustration to install the snap ring.



    C153481E04
  1. Check that the brake snap ring stopper can be turned by hand.
    Text in Illustration 
    *1
    Snap Ring
    *2
    Brake Snap Ring Stopper
    *a
    Correctly Installed

    NOTICE:
    If the brake snap ring stopper cannot be turned by hand, the brake snap ring stopper may have been installed upside down, or a snap ring may not have been completely located in the groove on the front oil pump assembly. Remove and reinstall the snap ring and the brake snap ring stopper.



32. INSPECT CLEARANCE OF NO. 1 BRAKE


    C305723E01
  1. Apply compressed air to the oil pressure supply hole shown in the illustration, and check the operation of the No. 1 brake piston.
    Text in Illustration 
    *1
    No. 1 Brake Piston
    *a
    Clearance

  1. Set a dial indicator as shown in the illustration.

  1. Using a dial indicator, measure the clearance of the No. 1 brake while applying compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    Standard Clearance:
    0.807 to 0.974 mm (0.0318 to 0.0383 in.)

    HINT:
    1. Measure the clearance at 3 points where the brake piston diameter is approximately 140 mm (5.51 in.) and calculate the average.
      If the clearance is not as specified, select an appropriate No. 1 brake flange so that the clearance will be within the specified range.
    2. There are 7 No. 1 brake flanges of different thicknesses.

    No. 1 Brake Flange Thickness: mm (in.) 
    Mark
    Thickness
    30
    3.0 (0.118)
    31
    3.1 (0.122)
    32
    3.2 (0.126)
    33
    3.3 (0.130)
    34
    3.4 (0.134)
    35
    3.5 (0.138)
    36
    3.6 (0.142)



33. INSTALL UNDERDRIVE PLANETARY SUN GEAR


    C141538E01
  1. Coat the thrust needle roller bearing with ATF and install it to the front oil pump assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Underdrive Planetary Sun Gear
    Bearing Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    57.7 (2.27)
    75.2 (2.96)

    NOTICE:
    Be sure to install the thrust needle roller bearing so that the temper colored side of the race is visible.

  1. Install the underdrive planetary sun gear to the front oil pump assembly.



34. INSTALL INPUT SHAFT SUB-ASSEMBLY


    C141539E02
  1. Coat 3 new input shaft oil seal rings with ATF and install them to the input shaft sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Race
    *2
    Thrust Needle Roller Bearing
    *3
    Input Shaft Oil Seal Ring
    *4
    Input Shaft Sub-assembly

    NOTICE:
    Do not expand the gap of the input shaft oil seal rings excessively.

  1. Coat the thrust needle roller bearing and thrust needle roller race with ATF, and install them to the input shaft sub-assembly.
    Bearing and Race Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    29.1 (1.15)
    48.6 (1.91)
    Race
    30.7 (1.21)
    48.3 (1.90)

    NOTICE:
    Be sure to install the thrust needle roller bearing in the correct direction.



    C136459
  1. Install the input shaft sub-assembly to the front oil pump assembly.



35. INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY


    C290582E03
  1. Using a snap ring expander, install the snap ring to the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Planetary Sun Gear Sub-assembly
    *2
    Underdrive Planetary Gear Assembly
    *3
    Snap Ring

  1. Using a snap ring expander, install the planetary sun gear sub-assembly to the underdrive planetary gear assembly with the snap ring expanded.



36. INSTALL UNDERDRIVE PLANETARY RING GEAR

HINT:
Perform this procedure only when replacement of the underdrive planetary ring gear or No. 3 brake hub is necessary.



    C290583
  1. Install the snap ring to the underdrive planetary ring gear.



    C291382
  1. While compressing the snap ring with a screwdriver, install the underdrive planetary ring gear to the No. 3 brake hub.

    NOTICE:
    Confirm that the snap ring is correctly located in the groove of the No. 3 brake hub.



37. INSTALL NO. 3 BRAKE HUB


    C295196E01
  1. Coat the thrust needle roller bearing and thrust needle roller race with ATF and install them to the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Needle Roller Race
    Bearing and Race Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    62.6 (2.46)
    82.4 (3.24)
    Race
    65.9 (2.59)
    80.3 (3.16)

    NOTICE:
    Be sure to install the thrust needle roller bearing so that the temper colored side of the race is visible.



    C136454
  1. Install the No. 3 brake hub to the underdrive planetary gear assembly.



38. INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY


    C136458
  1. Install the underdrive planetary gear assembly to the front oil pump assembly.



39. INSTALL NO. 3 BRAKE DISC


    C136452E02
  1. Install the 2 No. 3 brake flanges, 3 No. 3 brake discs and 2 No. 3 brake plates to the front oil pump assembly.
    Text in Illustration 
    *1
    No. 3 Brake Flange
    *2
    No. 3 Brake Plate
    *3
    No. 3 Brake Disc

    NOTICE:
    Make sure that the No. 3 brake discs, No. 3 brake plates and No. 3 brake flanges are installed in the correct order.



    C136451E15
  1. Using a screwdriver, install the snap ring to the front oil pump assembly.

    NOTICE:
    1. Confirm that the snap ring is correctly located in the groove of the front oil pump assembly.
    2. Make sure that the snap ring ends are positioned as shown in the illustration (A).



40. INSPECT CLEARANCE OF NO. 3 BRAKE


  1. Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (A)) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the flange.


    C315372E01


    Text in Illustration 
    *1
    Front Oil Pump Assembly
    *2
    No. 3 Brake Piston
    *3
    No. 3 Brake Flange
    -
    -
    *a
    Dimension (A)
    *b
    Dimension (B)
    *c
    Contact Surface of Front Oil Pump Assembly
    -
    -

    HINT:
    Measure the distance (Dimension (A)) at 3 points where the No. 3 brake flange diameter is approximately 166 mm (6.54 in.) and calculate the average.

  1. Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (B)).

    HINT:
    Measure the distance (Dimension (B)) at 3 points where the No. 3 brake piston diameter is approximately 166 mm (6.54 in.) and calculate the average.

  1. Calculate the clearance value using the following formula:
    Clearance = Dimension (B) - Dimension (A)

    Standard Clearance:
    0.599 to 0.761 mm (0.0236 to 0.0300 in.)

    If the clearance is not as specified, select an appropriate No. 3 brake flange so that the clearance will be within the specified range.



  1. Adjust clearance of No. 3 brake piston:



      C317753E02
    1. Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the front oil pump assembly.
      Text in Illustration 
      *a
      Protective Tape



    2. C317765E01
    3. Remove the No. 3 brake flange from the front oil pump assembly.
      Text in Illustration 
      *1
      No. 3 Brake Flange



    4. Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (A)) while a load of 500 N (51 kgf, 112.4 lbf) is being applied to the No. 3 brake disc.


      C323042E01


      Text in Illustration 
      *1
      Front Oil Pump Assembly
      *2
      No. 3 Brake Piston
      *3
      No. 3 Brake Disc
      -
      -
      *a
      Dimension (A)
      *b
      Dimension (B)
      *c
      Contact Surface of Front Oil Pump Assembly
      -
      -

      HINT:
      Measure the distance (Dimension (A)) at 3 points where the No. 3 brake disc diameter is approximately 166 mm (6.54 in.) and calculate the average.

    5. Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (B)).

      HINT:
      Measure the distance (Dimension (B)) at 3 points where the No. 3 brake piston diameter is approximately 166 mm (6.54 in.) and calculate the average.

    6. Calculate the thickness of the replacement No. 3 brake flange using the following formula:

      Thickness of Replacement No. 3 Brake Flange:
      Dimension (B) - Dimension (A) - (0.599 to 0.761 mm (0.0236 to 0.0300 in.))

      HINT:
      There are 9 No. 3 brake flanges of different thicknesses.

      No. 3 Brake Flange Thickness: mm (in.) 
      Mark
      Thickness
      37
      3.7 (0.146)
      38
      3.8 (0.150)
      39
      3.9 (0.154)
      40
      4.0 (0.157)
      41
      4.1 (0.161)
      42
      4.2 (0.165)
      43
      4.3 (0.169)
      44
      4.4 (0.173)
      45
      4.5 (0.177)



    7. C317765E01
    8. Install the No. 3 brake flange to the front oil pump assembly.
      Text in Illustration 
      *1
      No. 3 Brake Flange



    9. C274824E01
    10. Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the front oil pump assembly.

      NOTICE:
      1. Confirm that the snap ring is correctly located in the groove of the front oil pump assembly.
      2. Make sure that the snap ring ends are positioned as shown in the illustration (A).



41. INSTALL FRONT OIL PUMP BODY O-RING


    C293910
  1. Coat a new front oil pump body O-ring with ATF and install it to the front oil pump body sub-assembly.



42. INSTALL FRONT OIL PUMP ASSEMBLY


    C294585E05
  1. Coat a new O-ring with ATF and install it to the transaxle case sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    O-ring

  1. Coat the thrust needle roller bearing with ATF.

  1. Install the thrust needle roller bearing to the counter drive gear nut.
    Bearing and Race Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    53.1 (2.09)
    79 (3.11)

    NOTICE:
    Be sure to install the thrust needle roller bearing so that the temper colored side of the race is visible.

  1. Coat the thrust needle roller race with MP grease.



    C293908E01
  1. Install the thrust needle roller race to the underdrive planetary gear assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Race
    Bearing and Race Diameter: mm (in.) 
    -
    Inside
    Outside
    Race
    59.4 (2.34)
    77 (3.03)



    C136450E02
  1. Coat a new gasket with ATF and install it to the front oil pump assembly.
    Text in Illustration 
    *1
    Gasket

  1. Install the front oil pump assembly to the transaxle case sub-assembly with the 7 bolts.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



43. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE


    C136449E01
  1. Install the differential gear lube apply tube to the transaxle housing.

    NOTICE:
    Insert the differential gear lube apply tube to the transaxle housing until it makes contact with the stopper.

  1. Install the clamp to the differential gear lube apply tube with the bolt.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    NOTICE:
    There should be clearance between the differential gear lube apply tube and clamp.



44. INSTALL TRANSAXLE HOUSING


    C296566
  1. Clean and degrease the 3 bolts and installation holes in the transaxle case sub-assembly.

  1. Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.

    NOTICE:
    Make sure that there is no ATF on the contact surfaces of the transaxle housing and transaxle case sub-assembly.



    C138263E04
  1. Apply FIPG to the transaxle case sub-assembly.
    Text in Illustration 
    *a
    FIPG

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Apply FIPG in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface of the transaxle case sub-assembly.



    C294586
  1. Install the transaxle housing to the transaxle case sub-assembly with the 17 bolts.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



    A057108E36
  1. Apply adhesive to 2 or 3 threads on the ends of the 3 bolts.
    Text in Illustration 
    *a
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    NOTICE:
    In order to ensure proper installation of the 3 bolts, apply adhesive to the 3 bolts and install them within 3 minutes of adhesive application.



    C294583
  1. Install the 3 bolts.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



45. INSTALL NO. 1 CLUTCH DISC


    C136446E03
  1. Install the No. 1 clutch flange, 4 No. 1 clutch discs and 4 No. 1 clutch plates to the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    No. 1 Clutch Flange
    *2
    No. 1 Clutch Plate
    *3
    No. 1 Clutch Disc

    NOTICE:
    Make sure that the No. 1 clutch flange, No. 1 clutch discs and No. 1 clutch plates are installed in the correct order.



    C136445
  1. Using a screwdriver, install the 2 snap rings to the direct multiple disc clutch assembly.

    NOTICE:
    Confirm that the snap rings are correctly located in the groove of the direct multiple disc clutch assembly.



46. INSPECT CLEARANCE OF NO. 1 CLUTCH DISC
  1. Install the direct multiple disc clutch assembly to the rear transaxle cover sub-assembly.



    C138728
  1. Using a dial indicator, measure the No. 1 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).

    Pack Clearance:
    0.806 to 0.974 mm (0.0317 to 0.0383 in.)

    HINT:
    1. Measure the clearance at 3 points where the No. 1 clutch flange diameter is approximately 152 mm (5.98 in.) and calculate the average.
      If the pack clearance is not as specified, select an appropriate No. 1 clutch flange so that the pack clearance will be within the specified range.
    2. There are 6 No. 1 clutch flanges of different thicknesses.

    No. 1 Clutch Flange Thickness: mm (in.) 
    Mark
    Thickness
    30
    3.0 (0.118)
    31
    3.1 (0.122)
    32
    3.2 (0.126)
    33
    3.3 (0.130)
    34
    3.4 (0.134)
    35
    3.5 (0.138)



47. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY


    C141542E02
  1. Coat the thrust needle roller bearing and thrust needle roller race with ATF and install them to the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Needle Roller Race
    Bearing and Race Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    28 (1.10)
    47.1 (1.85)
    Race
    26.1 (1.03)
    44 (1.73)

    NOTICE:
    Be sure to install the thrust needle roller bearing so that the temper colored side of the race is visible.



    C136437
  1. Install the rear planetary sun gear assembly to the direct multiple disc clutch assembly.



    C136436
  1. Using a snap ring expander, install the snap ring to the direct multiple disc clutch assembly.



48. INSTALL NO. 2 CLUTCH DISC


    C136435E03
  1. Install the No. 2 clutch flange, 3 No. 2 clutch discs and 3 No. 2 clutch plates to the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    No. 2 Clutch Plate
    *2
    No. 2 Clutch Disc
    *3
    No. 2 Clutch Flange

    NOTICE:
    Make sure that the No. 2 clutch flange, No. 2 clutch discs and No. 2 clutch plates are installed in the correct order.



49. INSTALL DIRECT MULTIPLE DISC CLUTCH SNAP RING


    C141535
  1. Install the No. 2 direct clutch piston to the direct multiple disc clutch assembly.

    NOTICE:
    Be sure to engage the claws on the direct multiple disc clutch assembly in the grooves on the No. 2 direct clutch piston.



    C136433E01
  1. Using a screwdriver, install the direct multiple disc clutch snap ring to the direct multiple disc clutch assembly.

    NOTICE:
    1. Position the opening of the direct multiple disc clutch snap ring as shown in the illustration.
    2. Confirm that the direct multiple disc clutch snap ring is correctly located in the groove of the direct multiple disc clutch assembly.



50. INSPECT CLEARANCE OF NO. 2 CLUTCH DISC
  1. Install the direct multiple disc clutch assembly to the rear transaxle cover sub-assembly.



    C138727E01
  1. Using a dial indicator, measure the No. 2 clutch pack clearance while applying and releasing compressed air (200 kPa, 2.0 kgf/cm2, 29 psi).
    Text in Illustration 
    *1
    No. 2 Direct Clutch Piston

    Pack Clearance:
    0.544 to 0.744 mm (0.0214 to 0.0293 in.)

    HINT:
    1. Measure the clearance at 3 points where the diameter of the No. 2 direct clutch piston is approximately 152 mm (5.98 in.) and calculate the average.
      If the pack clearance is not as specified, select an appropriate No. 2 clutch flange so that the pack clearance will be within the specified range.
    2. There are 6 No. 2 clutch flanges of different thicknesses.

    No. 2 Clutch Flange Thickness: mm (in.) 
    Mark
    Thickness
    30
    3.0 (0.118)
    31
    3.1 (0.122)
    32
    3.2 (0.126)
    33
    3.3 (0.130)
    34
    3.4 (0.134)
    35
    3.5 (0.138)



51. INSTALL DIRECT MULTIPLE DISC CLUTCH ASSEMBLY


    C296565E01
  1. Coat a new O-ring with ATF and install it to the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Intermediate Shaft Oil Seal
    *2
    O-ring

  1. Coat a new intermediate shaft oil seal with ATF and install it to the direct multiple disc clutch assembly.



    C141543E01
  1. Coat the thrust needle roller bearing with ATF and install it to the direct multiple disc clutch assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Direct Multiple Disc Clutch Assembly
    Bearing Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    61.2 (2.41)
    79 (3.11)

  1. Install the direct multiple disc clutch assembly to the transaxle case sub-assembly.

  1. Clean the contact surfaces of the transaxle case sub-assembly and rear transaxle cover sub-assembly.



    C138269E03
  1. Place a straightedge on the multiple direct clutch drum and measure the distance between the transaxle case sub-assembly and the straightedge using a vernier caliper (Dimension (A)).
    Text in Illustration 
    *a
    Dimension (A)



    C138268E04
  1. Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension (B)).
    Text in Illustration 
    *a
    Dimension (B)

  1. Calculate the end play value using the following formula:
    End play = Dimension (B) - Dimension (A) - Thrust needle roller bearing thickness

    End Play:
    0.007 to 1.113 mm (0.000276 to 0.0438 in.)



52. INSTALL REAR TRANSAXLE COVER SUB-ASSEMBLY


    C205308E01
  1. Using SST and a hammer, install a new needle roller bearing to the rear transaxle cover sub-assembly.

    SST
    09950-60010   (09951-00220)
    09950-70010   (09951-07100)

    Standard Depth:
    21.5 to 21.9 mm (0.846 to 0.862 in.)



    C324917E01
  1. Apply adhesive to the 2 "TORX" screws.
    Text in Illustration 
    *a
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    NOTICE:
    In order to ensure proper sealing of the 2 "TORX" screws, apply adhesive to the 2 "TORX" screws and install them within 10 minutes of adhesive application.



    C162442E01
  1. Using a T30 "TORX" socket wrench, install the rear transaxle cover plate to the rear transaxle cover sub-assembly with the 2 "TORX" screws.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    C299131E01
  1. Coat 2 new oil seal rings with ATF and install them to the rear transaxle cover sub-assembly.
    Text in Illustration 
    *1
    Oil Seal Ring

    NOTICE:
    Confirm that the 2 oil seal rings are correctly located in the grooves of the rear transaxle cover sub-assembly.



    C297890E01
  1. Coat the thrust needle roller bearing and thrust needle roller race with MP grease and install them to the rear transaxle cover sub-assembly.
    Text in Illustration 
    *1
    Thrust Needle Roller Bearing
    *2
    Thrust Needle Roller Race
    Bearing and Race Diameter: mm (in.) 
    -
    Inside
    Outside
    Bearing
    48.9 (1.93)
    72.0 (2.83)
    Race
    52.2 (2.06)
    70.4 (2.77)



    C136432E01
  1. Coat 3 new O-rings with ATF and install them to the transaxle case sub-assembly.

    NOTICE:
    Ensure that the O-rings are not twisted.



    C296567
  1. Clean and degrease the 2 bolts and installation holes in the transaxle case sub-assembly.

  1. Remove any remaining seal packing from the contact surfaces of the rear transaxle cover sub-assembly and transaxle case sub-assembly.

    NOTICE:
    Make sure that there is no ATF on the contact surfaces.



    C138271E05
  1. Apply FIPG to the transaxle case sub-assembly.
    Text in Illustration 
    *a
    FIPG

    FIPG:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Apply FIPG in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface of the transaxle case sub-assembly.



    C136431E03
  1. Install the rear transaxle cover sub-assembly to the transaxle case sub-assembly with the 12 bolts.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



    A057108E36
  1. Apply adhesive to 2 or 3 threads on the ends of the 2 bolts.
    Text in Illustration 
    *a
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    NOTICE:
    In order to ensure proper installation of the 2 bolts, apply adhesive to the 2 bolts and install them within 3 minutes of adhesive application.



    C296570
  1. Install the 2 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }



    C136430
  1. Install a new gasket to the refill plug.

  1. Install the refill plug to the rear transaxle cover sub-assembly.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



    C288350
  1. Coat 3 new O-rings with ATF and install them to the 3 No. 1 automatic transaxle case plugs.

  1. Install the 3 No. 1 automatic transaxle case plugs to the rear transaxle cover sub-assembly.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



53. INSPECT INPUT SHAFT SUB-ASSEMBLY END PLAY


    C136696
  1. Using a dial indicator, measure the input shaft sub-assembly end play.

    End Play:
    0.012 to 1.250 mm (0.000473 to 0.0492 in.)



54. INSTALL TRANSAXLE CASE GASKET


    C136429E01
  1. Coat 2 new transaxle case gaskets with ATF and install them to the transaxle case sub-assembly.



55. INSTALL TRANSMISSION VALVE BODY ASSEMBLY
  1. Coat the O-ring of the transmission wire with ATF.



    C326386E02
  1. Insert the manual valve lever shaft sub-assembly pin into the groove on the end of the manual valve as shown in the illustration and temporarily install the transmission valve body assembly to the transaxle case sub-assembly with the 11 bolts.
    Text in Illustration 
    *1
    Manual Valve Lever Shaft Sub-assembly Pin
    *2
    Manual Valve
    *a
    Positioning Bolt

    NOTICE:
    1. When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case sub-assembly to interfere with each other.
    2. Be sure to insert the manual valve lever shaft sub-assembly pin into the groove on the end of the manual valve.

    -
    Bolt Length
    Bolt (A)
    25 mm (0.984 in.)
    Bolt (B)
    30 mm (1.18 in.)
    Bolt (C)
    35 mm (1.38 in.)
    Bolt (D)
    45 mm (1.77 in.)
    Bolt (E)
    55 mm (2.17 in.)

  1. Fully tighten the 2 positioning bolts shown in the illustration.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Fully tighten the 9 bolts to install the transmission valve body assembly.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



56. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    C136688E05
  1. Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Ensure that the O-ring is not twisted or pinched.



    C136687
  1. Install the valve body oil strainer assembly to the transmission valve body assembly with the 2 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



57. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY


    C134963E03
  1. Install the 2 transmission oil cleaner magnets to the automatic transaxle oil pan sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Transmission Oil Cleaner Magnet

  1. Install a new automatic transaxle oil pan gasket to the automatic transaxle oil pan sub-assembly.



    C296568
  1. Clean and degrease the bolt and installation hole in the transaxle case sub-assembly.



    C288671
  1. Install the automatic transaxle oil pan sub-assembly with automatic transaxle oil pan gasket to the transaxle case sub-assembly with the 17 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    NOTICE:
    Completely remove any oil or grease from the contact surfaces of the transaxle case sub-assembly and automatic transaxle oil pan sub-assembly with automatic transaxle oil pan gasket before installation.



    A057108E36
  1. Apply adhesive to the bolt.
    Text in Illustration 
    *a
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    In order to ensure proper installation of the bolt, apply adhesive to the bolt and install it within 3 minutes of adhesive application.



    C243140
  1. Install the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



    C141531
  1. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle oil pan sub-assembly.

    Torque:
    1.7 N*m{ 17 kgf*cm , 15 in.*lbf }



    C134961
  1. Using a 6 mm hexagon socket wrench, install the overflow plug and a new gasket to the automatic transaxle oil pan sub-assembly.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



58. INSTALL NO. 2 TRANSAXLE CASE PLUG
  1. Clean and degrease the 3 No. 2 transaxle case plugs and installation holes in the transaxle housing.

  1. Install 3 new gaskets to the 3 No. 2 transaxle case plugs.



    C324918E01
  1. Apply adhesive to the 3 No. 2 transaxle case plugs.
    Text in Illustration 
    *a
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    NOTICE:
    In order to ensure proper installation of the 3 No. 2 transaxle case plugs, apply adhesive to the 3 No. 2 transaxle case plugs and install them within 3 minutes of adhesive application.



    C134959
  1. Using a 6 mm hexagon socket wrench, install the 3 No. 2 transaxle case plugs to the transaxle housing.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }



59. INSTALL NO. 1 TRANSAXLE CASE PLUG


    C162438
  1. Coat 3 new O-rings with ATF and install them to the 3 No. 1 transaxle case plugs.

  1. Install the 3 No. 1 transaxle case plugs to the transaxle case sub-assembly.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



60. INSTALL OIL COOLER TUBE UNION (INLET OIL COOLER UNION)


    C289627
  1. Coat a new O-ring with ATF and install it to the oil cooler tube union (inlet oil cooler union).

  1. Install the oil cooler tube union (inlet oil cooler union) to the transaxle case sub-assembly.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



61. INSTALL OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)


    C289626
  1. Coat a new O-ring with ATF and install it to the oil cooler tube union (outlet oil cooler union).

  1. Install the oil cooler tube union (outlet oil cooler union) to the transaxle case sub-assembly.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



62. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C135733E11
  1. Align the protrusions of the park/neutral position switch assembly as shown in the illustration.
    Text in Illustration 
    *a
    Protrusion



    C136686
  1. Install the park/neutral position switch assembly to the transaxle case sub-assembly with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    1. Before installing the park/neutral position switch assembly, remove any dirt or rust on the manual valve lever shaft sub-assembly. Be sure to install the park/neutral position switch assembly straight along the manual valve lever shaft sub-assembly while being careful not to deform the plate spring that supports the manual valve lever shaft sub-assembly. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.
    2. After installing the park/neutral position switch assembly, confirm that the 2 protrusions on the park/neutral position switch assembly are aligned.



    C136685
  1. Install the transmission control shaft lever to the manual valve lever shaft sub-assembly with the washer and nut.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



63. INSTALL BREATHER PLUG HOSE


    C134952E04
  1. Coat a new O-ring with ATF and install it to the No. 2 breather plug (ATM).
    Text in Illustration 
    *1
    No. 1 Breather Plug (ATM)
    *2
    Breather Plug Hose
    *3
    No. 2 Breather Plug (ATM)
    *4
    O-ring

  1. Install the No. 1 breather plug (ATM) and No. 2 breather plug (ATM) to the breather plug hose.



    C190663
  1. Install the breather plug hose to the transaxle case sub-assembly.