Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM

AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM > INITIALIZATION

for Preparation Click here


NOTICE:
  1. Initialize the headlight leveling ECU assembly when the headlight leveling ECU assembly is replaced.
  2. Initialize the headlight leveling ECU assembly (set the zero point of the height control sensor in the headlight leveling ECU assembly) after the vehicle height changes due to replacement of suspension components or after performing operations such as removal and reinstallation or replacement of the rear height control sensor sub-assembly.
  3. Adjust the headlight aim after initializing the headlight leveling ECU assembly (for TMC, TMMR Made: Click here), (for TMMK Made: Click here).
  4. When a malfunction is detected in the automatic headlight beam level control system, height control sensor signal initialization is impossible. Perform troubleshooting before initialization.



1.PREPARE VEHICLE FOR INITIALIZATION
  1. Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.

  2. Check that there are no occupants in the vehicle.

  3. Turn off the headlights.

  4. Stop the vehicle on a level surface and keep the vehicle height unchanged.


NEXT


2.CHECK HEADLIGHT LEVELING WARNING


  1. Turn the ignition switch to ON, and check the headlight leveling warning.


    E314468E01


    Text in Illustration 
    *A
    for TMC, TMMR Made
    *B
    for TMMK Made

    OK:
    Condition
    Specified Condition
    The headlight leveling ECU assembly has been replaced with a new one.
    Headlight leveling warning repeatedly blinks 6 times at 2 Hz.
    Replacement of the rear height control sensor sub-assembly, removal and reinstallation of the rear height control sensor sub-assembly, replacement of the suspension, etc. has been performed.
    Headlight leveling warning is not displayed.



NG.
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


3.INITIALIZATION


    E106867E45
  1. Connect SST to terminals 4 (CG) and 8 (LVL) of the DLC3.

  2. SST
    09843-18040  


    E314469E01
  3. Turn the low beam headlights on and off using the light control switch within 20 seconds after connecting the terminals.

    HINT:
    The number of times the low beam headlights need to be turned on and off is determined by the present fuel level as shown below.
    Fuel Level
    Number of Times to Turn Low Beam Headlights On and Off
    Fuel level is within A range.
    1
    Fuel level is within B range.
    2
    Fuel level is within C range.
    3
    Fuel level is within D range.
    4
    Fuel level is within E range.
    5

    NOTICE:
    1. Turn the low beam headlights on and off at less than 3-second intervals.
    2. Be sure to operate the light control switch from outside the vehicle.

    Text in Illustration 
    *A
    for TMC, TMMR Made
    *B
    for TMMK Made

  4. Check the headlight leveling warning.

    OK:
    Condition
    Specified Condition
    The headlight leveling ECU assembly has been replaced with a new one.
    Blinks 6 times at 2 Hz → Repeatedly blinks N*1 times at 2 Hz.
    Replacement of the rear height control sensor sub-assembly, removal and reinstallation of the rear height control sensor sub-assembly, replacement of the suspension, etc. has been performed.
    Off → Repeatedly blinks N*1 times at 2 Hz.

    HINT:
    1. *1: The number of times that the headlight leveling warning blinks is determined by the number of times the low beam headlights are turned on and off.
    2. If initialization does not finish normally, disconnect SST from the DLC3 and turn the ignition switch off. Then, restart initialization from step 1.



NG.
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK

TURN IGNITION SWITCH OFF (END)