Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System)

DTC    B2799    Engine Immobiliser System Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communication with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted.

DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2799
One of the following conditions is met:
  1. Error in communication between ECM and transponder key ECU assembly.
  2. Error in communication lines.
  3. Communication ID is different during communication between ECM and transponder key ECU assembly.
  1. Wire harness or connector
  2. ECM
  3. Transponder key ECU assembly
  1. Start the engine and wait 10 seconds.
  2. After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started
-

Related Data List and Active Test 
DTC No.
Data List and Active Test
B2799
-

WIRING DIAGRAM


B255097E04


INSPECTION PROCEDURE

NOTICE:
  1. If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
  2. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

HINT:
If the transponder key ECU assembly DTC is output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Perform "DTC Output Confirmation Operation" procedure.

  1. Check for DTCs (Click here).

    OK:
    DTC B2799 is not output.

    Result:
    Result
    Proceed to
    DTC B2799 is output
    A
    Other DTCs are output
    B
    DTC B2799 is not output
    C



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


3.INSPECT ECM (TERMINAL IMO)


  1. Using an oscilloscope, check the waveform.


    B372938E01


    Text in Illustration 
    *a
    Component with harness connected
    (ECM)
    *b
    Waveform
    *c
    Approximately 160 ms
    *d
    Approximately 270 ms

    Measurement Condition:

    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    A25-29 (IMO) - Body ground
    Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform)

    OK:
    Waveform is similar to that shown in the illustration.

    Result:
    Result
    Proceed to
    Normal waveform
    A
    Terminal IMO stuck low (2.4 V or less)
    B
    Terminal IMO stuck high (12 V) or abnormal waveform
    C



B
Go to step 7

C
Go to step 11
A


4.INSPECT ECM (TERMINAL IMI)


  1. Using an oscilloscope, check the waveform.


    B372939E01


    Text in Illustration 
    *a
    Component with harness connected
    (ECM)
    *b
    Waveform
    *c
    Approximately 160 ms
    *d
    Approximately 270 ms

    Measurement Condition:

    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    A25-28 (IMI) - Body ground
    Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform)

    OK:
    Waveform is similar to that shown in the illustration.



NG
Go to step 9
OK


5.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


Go to step 7

6.CHECK WHETHER ENGINE STARTS
  1. Using a registered door control transmitter assembly, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON

    OK:
    Engine starts normally.



NG
Go to step 11
OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE) 

7.INSPECT ECM (IMO TERMINAL VOLTAGE)


    A255690E70
  1. Disconnect the A25 ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A25-29 (IMO) - Body ground
    Ignition switch turned to ON using registered door control transmitter assembly
    Terminal IMO stuck low (2.4 V or less)

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)

    Result:
    Result
    Proceed to
    Terminal IMO stuck low (2.4 V or less)
    A
    Terminal IMO stuck high (12 V) or abnormal waveform
    B



B
Go to step 11
A


8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
  1. Disconnect the I19 transponder key ECU assembly connector.

  1. Disconnect the A25 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I19-12 (EFII) - A25-29 (IMO)
    Always
    Below 1 Ω
    I19-12 (EFII) or A25-29 (IMO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly with a new one.

    HINT:
    Refer to Service Bulletin.

    NOTICE:
    Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Service Bulletin.


NEXT


10.CHECK WHETHER ENGINE STARTS
  1. Using a registered door control transmitter assembly, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON

    OK:
    Engine starts normally.



NG
REPLACE ECM (Click here)
OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE) 

11.REPLACE ECM
  1. Temporarily replace the ECM with a new one (Click here).


NEXT


12.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


13.CHECK WHETHER ENGINE STARTS
  1. Using a registered door control transmitter assembly, turn the ignition switch to ON.

  1. Check that the engine starts 5 seconds after the ignition switch was turned to ON

    OK:
    Engine starts normally.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

END (ECM WAS DEFECTIVE)