DTC B2799 Engine Immobiliser System Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
| B2799 | One of the following conditions is met:
|
|
|
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
| Engine cannot be started | - |
| DTC No. | Data List and Active Test |
| B2799 | - |

| 1.CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2.CHECK FOR DTC |
Perform "DTC Output Confirmation Operation" procedure.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B2799 is output | A |
| Other DTCs are output | B |
| DTC B2799 is not output | C |
|
| ||||
|
| ||||
| A | |
| 3.INSPECT ECM (TERMINAL IMO) |
Using an oscilloscope, check the waveform.

| *a | Component with harness connected (ECM) | *b | Waveform |
| *c | Approximately 160 ms | *d | Approximately 270 ms |
| Tester Connection | Condition | Tool Setting | Specified Condition |
| A25-29 (IMO) - Body ground | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal | 2 V/DIV., 500 ms./DIV. | Pulse generation (See waveform) |
| Result | Proceed to |
| Normal waveform | A |
| Terminal IMO stuck low (2.4 V or less) | B |
| Terminal IMO stuck high (12 V) or abnormal waveform | C |
|
| ||||
|
| ||||
| A | |
| 4.INSPECT ECM (TERMINAL IMI) |
Using an oscilloscope, check the waveform.

| *a | Component with harness connected (ECM) | *b | Waveform |
| *c | Approximately 160 ms | *d | Approximately 270 ms |
| Tester Connection | Condition | Tool Setting | Specified Condition |
| A25-28 (IMI) - Body ground | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal | 2 V/DIV., 500 ms./DIV. | Pulse generation (See waveform) |
|
| ||||
| OK | |
| 5.REGISTER ECU COMMUNICATION ID |
Register the ECU communication ID.
| NEXT | |
| Go to step 7 |
| 6.CHECK WHETHER ENGINE STARTS |
Using a registered door control transmitter assembly, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON
|
| ||||
| OK | ||
| ||
| 7.INSPECT ECM (IMO TERMINAL VOLTAGE) |
![]() |
Disconnect the A25 ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-29 (IMO) - Body ground | Ignition switch turned to ON using registered door control transmitter assembly | Terminal IMO stuck low (2.4 V or less) |
| *a | Front view of wire harness connector (to ECM) |
| Result | Proceed to |
| Terminal IMO stuck low (2.4 V or less) | A |
| Terminal IMO stuck high (12 V) or abnormal waveform | B |
|
| ||||
| A | |
| 8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM) |
Disconnect the I19 transponder key ECU assembly connector.
Disconnect the A25 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I19-12 (EFII) - A25-29 (IMO) | Always | Below 1 Ω |
| I19-12 (EFII) or A25-29 (IMO) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.REPLACE TRANSPONDER KEY ECU ASSEMBLY |
Replace the transponder key ECU assembly with a new one.
| NEXT | |
| 10.CHECK WHETHER ENGINE STARTS |
Using a registered door control transmitter assembly, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON
|
| ||||
| OK | ||
| ||
| 11.REPLACE ECM |
Temporarily replace the ECM with a new one (Click here).
| NEXT | |
| 12.REGISTER ECU COMMUNICATION ID |
Register the ECU communication ID.
| NEXT | |
| 13.CHECK WHETHER ENGINE STARTS |
Using a registered door control transmitter assembly, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON
|
| ||||
| OK | ||
| ||