Home › Vehicle Exterior › WINDOW / GLASS › FRONT DOOR POWER WINDOW REGULATOR MOTOR (for TMMK Made)

FRONT DOOR POWER WINDOW REGULATOR MOTOR (for TMMK Made) > INSPECTION

for Preparation Click here



1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    E292072E01
  1. Connect a positive (+) battery lead to terminal 2 (B).

    NOTICE:
    Do not connect a positive (+) battery lead to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

  1. Connect a negative (-) battery lead to terminals 1 (GND) and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows:

    OK:

    Battery Connection
    Specified Condition
    1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).
    3. Disconnect and reconnect the negative (-) battery lead to terminal 10 (UP) within 1 second.
    Motor gear rotates clockwise
    1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).
    3. Disconnect and reconnect the negative (-) battery lead to terminal 7 (DOWN) within 1 second.
    Motor gear rotates counterclockwise

    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Motor Assembly LH)
    *b
    Clockwise
    *c
    Counterclockwise
    *d
    Motor Gear
    1. If the result is not as specified, replace the power window regulator motor assembly LH.

    NOTICE:
    Initialize the power window control system after installing the power window regulator motor and regulator assembly.



2. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


    E292071E01
  1. Connect a positive (+) battery lead to terminal 2 (B).

    NOTICE:
    Do not connect a positive (+) battery lead to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

  1. Connect a negative (-) battery lead to terminals 1 (GND) and 7 (DOWN) or 10 (UP).

  1. Check that the motor gear rotates smoothly as follows:

    OK:

    Battery Connection
    Specified Condition
    1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 10 (UP).
    3. Disconnect and reconnect the negative (-) battery lead to terminal 10 (UP) within 1 second.
    Motor gear rotates counterclockwise
    1. Connect a positive (+) battery lead to terminal 2 (B), connect a negative (-) battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.
    2. With terminals 2 (B) and 1 (GND) connected, connect a negative (-) battery lead to terminal 7 (DOWN).
    3. Disconnect and reconnect the negative (-) battery lead to terminal 7 (DOWN) within 1 second.
    Motor gear rotates clockwise

    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Motor Assembly RH)
    *b
    Clockwise
    *c
    Counterclockwise
    *d
    Motor Gear
    1. If the result is not as specified, replace the power window regulator motor assembly RH.

    NOTICE:
    Initialize the power window control system after installing the power window regulator motor and regulator assembly.