Home › Engine / Hybrid System ยท 6AR-FSE › INTAKE / EXHAUST › EXHAUST MANIFOLD

EXHAUST MANIFOLD > REMOVAL

for Preparation Click here



1. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
  1. Remove the 3 screws and front wheel opening extension pad RH.



2. REMOVE ENGINE UNDER COVER RH
  1. Remove the 3 screws, 3 clips and engine under cover RH.



3. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
  1. Remove the 3 screws and front wheel opening extension pad LH.



4. REMOVE ENGINE UNDER COVER LH
  1. Remove the 3 screws, 2 clips and engine under cover LH.



5. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)


    A338735
  1. Disconnect the heated oxygen sensor connector.



    A338736
  1. Remove the 2 bolts, 2 compression springs, 2 nuts and front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and center exhaust pipe assembly.

  1. Disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust pipe support.

  1. Remove the 2 exhaust pipe gaskets from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).



6. REMOVE INLET AIR CLEANER ASSEMBLY


    A338524
  1. Remove the 2 bolts and inlet air cleaner assembly.



7. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A209579
  1. Remove the 4 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).



8. REMOVE AIR FUEL RATIO SENSOR


    A338030
  1. Disengage the 3 wire harness clamps.



    A338570E01
  1. Disconnect the air fuel ratio sensor connector.

  1. Using SST, remove the air fuel ratio sensor from the exhaust manifold.

    SST
    09224-00011  

    NOTICE:
    If the air fuel ratio sensor has been struck or dropped, replace it.



9. REMOVE EGR PIPE CONNECTOR


    A339007
  1. Remove the 4 bolts, nut and EGR pipe connector from the exhaust manifold converter sub-assembly (TWC: Front Catalyst), EGR cooler assembly and cylinder block sub-assembly.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Nut



    A338734
  1. Remove the 2 EGR cooler gaskets from the EGR pipe connector.



10. REMOVE MANIFOLD STAY


    A338738
  1. Remove the bolt, nut and manifold stay from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly.



11. REMOVE NO. 2 MANIFOLD STAY


    A338737
  1. Remove the bolt, nut and No. 2 manifold stay from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly.



12. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)


    A195979
  1. Remove the 5 nuts and exhaust manifold converter sub-assembly (TWC: Front Catalyst) from the cylinder head sub-assembly.



    A195981
  1. Remove the exhaust manifold gasket from the cylinder head sub-assembly.



13. REMOVE NO. 1 MANIFOLD CONVERTER INSULATOR


    A338995
  1. Remove the 3 bolts and No. 1 manifold converter insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).



14. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A211654
  1. Remove the 2 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).



15. REMOVE STUD BOLT

HINT:
If a stud bolt is deformed or the threads are damaged, replace it.



    A338996
  1. Using an E8 "TORX" socket wrench, remove the stud bolt from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).