POWER STEERING ECU > INSTALLATION |
| 1. INSTALL POWER STEERING ECU WITH MOTOR ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) |
Install a new electric power steering motor shaft damper to the electric power steering column sub-assembly.
Install a new electric power steering motor shaft spacer to the electric power steering column sub-assembly.
![]() |
Temporarily install the power steering ECU with motor assembly to the electric power steering column sub-assembly with 3 bolts.
![]() |
Install the 2 service nuts to the steering main shaft.
| *1 | Service Nut |
Simultaneously rotate the service nut that was installed first counterclockwise and rotate the service nut that was installed second clockwise to lock them.
![]() |
Secure the steering column assembly in a vise using aluminum plates as shown in the illustration.
| *1 | Aluminum Plate |
| *2 | Wooden Block |
![]() |
Turn the steering main shaft once 180 degrees to the left and then 180 degrees to the right at a speed of 60 rpm, and repeat 2 to 3 times to adjust the axis of the power steering ECU with motor assembly.
Tighten the 3 bolts.
![]() |
Measure the turning torque of the steering main shaft.
Remove the 2 service nuts from the steering main shaft.
Connect the connector to the power steering ECU with motor assembly.
| 2. CONNECT ECU WIRE SUB-ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) |
Connect the 2 connectors to the power steering ECU with motor assembly.
| 3. INSTALL POWER STEERING ECU WITH MOTOR ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) |
Install a new electric power steering motor shaft damper to the electric power steering column sub-assembly.
Install a new electric power steering motor shaft spacer to the electric power steering column sub-assembly.
![]() |
Temporarily install the power steering ECU with motor assembly to the electric power steering column sub-assembly with 3 bolts.
![]() |
Install the 2 service nuts to the steering main shaft.
| *1 | Service Nut |
Simultaneously rotate the service nut that was installed first counterclockwise and rotate the service nut that was installed second clockwise to lock them.
![]() |
Securely set the steering column assembly on a wooden block or similar item.
| *1 | Wooden Block |
![]() |
Turn the steering main shaft once 180 degrees to the left and then 180 degrees to the right at a speed of 60 rpm, and repeat 2 to 3 times to adjust the axis of the power steering ECU with motor assembly.
Tighten the 3 bolts.
![]() |
Measure the turning torque of the steering main shaft.
Remove the 2 service nuts from the steering main shaft.
Connect the connector to the power steering ECU with motor assembly.
| 4. CONNECT ECU WIRE SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) |
Connect the 2 connectors to the power steering ECU with motor assembly.
| 5. INSTALL POWER STEERING ECU PROTECTOR |
Install a new power steering ECU protector to the power steering ECU with motor assembly.
| 6. INSTALL STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (w/o Smart Entry and Start System) |
Secure the steering column assembly in a vise.
![]() |
Temporarily install the steering column upper with switch bracket assembly to the steering column assembly with 2 new tapered-head bolts.
Tighten the 2 tapered-head bolts until the bolt heads break off.
| 7. INSTALL STEERING LOCK ACTUATOR ASSEMBLY (w/ Smart Entry and Start System) |
for Manual Tilt and Manual Telescopic Steering Column
Secure the steering column assembly in a vise.
![]() |
Temporarily install the steering lock actuator assembly to the steering column assembly with 2 new tapered-head bolts.
Tighten the 2 tapered-head bolts until the bolt heads break off.
for Power Tilt and Power Telescopic Steering Column
![]() |
Temporarily install the steering lock actuator assembly to the steering column assembly with the 2 new tapered-head bolts.
Tighten the 2 tapered-head bolts until the bolt heads break off.
| 8. INSTALL STEERING COLUMN ASSEMBLY |
| 9. ASSIST MAP WRITING |