Home › Drivetrain ยท U760E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL OIL SEAL

DIFFERENTIAL OIL SEAL > REPLACEMENT

for Preparation Click here



1. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Remove the front wheel opening extension pad LH, engine under cover LH and front fender apron seal LH.



    C201682
  1. Remove the refill plug and gasket from the automatic transaxle assembly.



    C201683E03
  1. Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle assembly.
    Text in Illustration 
    *1
    No. 1 Transmission Oil Filler Tube
    *2
    Overflow Plug
    *3
    Hexagon Socket Wrench



    C201684E04
  1. Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the automatic transaxle assembly.
    Text in Illustration 
    *1
    No. 1 Transmission Oil Filler Tube
    *2
    Hexagon Socket Wrench
    *a
    Overflow Plug Hole

  1. Drain automatic transaxle fluid from the automatic transaxle assembly.



    C201684E04
  1. Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle assembly.

    Torque:
    0.8 N*m{ 8 kgf*cm , 7 in.*lbf }

    Text in Illustration 
    *1
    No. 1 Transmission Oil Filler Tube
    *2
    Hexagon Socket Wrench
    *a
    Overflow Plug Hole



    C201683E03
  1. Using a 6 mm hexagon socket wrench, install a new gasket and the overflow plug to the automatic transaxle assembly.

    Torque:
    40 N*m{ 408 kgf*cm , 29 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Transmission Oil Filler Tube
    *2
    Overflow Plug
    *3
    Hexagon Socket Wrench



    C201682
  1. Install a new gasket and the refill plug to the automatic transaxle assembly.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



2. REMOVE FRONT DRIVE SHAFT ASSEMBLY
(Click here)


3. REMOVE TRANSAXLE CASE OIL SEAL


    C201712E01
  1. Using SST, tap out the transaxle case oil seal.

    SST
    09308-00010  



4. REMOVE DRIVE SHAFT BEARING BRACKET


    A196633
  1. Remove the 3 bolts and drive shaft bearing bracket.



5. REMOVE FRONT TRANSAXLE CASE OIL SEAL


    C201713E01
  1. Using SST, tap out the front transaxle case oil seal.

    SST
    09308-00010  



6. INSTALL FRONT TRANSAXLE CASE OIL SEAL


    C201715E01
  1. Using SST and a hammer, tap in a new front transaxle case oil seal.

    SST
    09316-60011   (09316-00011)

    Oil seal driven in depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

    NOTICE:
    Check that the oil seal is installed in the correct direction.

  1. Coat the lip of the front transaxle case oil seal with MP grease.



7. INSTALL DRIVE SHAFT BEARING BRACKET
  1. Install the drive shaft bearing bracket with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



8. INSTALL TRANSAXLE CASE OIL SEAL


    C201714E01
  1. Using SST and a hammer, tap in a new transaxle case oil seal.

    SST
    09316-10010  
    09950-70010   (09951-07150)

    Oil seal driven in depth:
    -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

    NOTICE:
    Check that the oil seal is installed in the correct direction.

  1. Coat the lip of the transaxle case oil seal with MP grease.



9. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
  1. Install a new front drive shaft hole snap ring LH.

    NOTICE:
    Face the end gap of the front drive shaft hole snap ring downward.



10. INSTALL FRONT DRIVE SHAFT ASSEMBLY
(Click here)


11. ADD AUTOMATIC TRANSAXLE FLUID
(Click here)