Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for TMMK Made Power Seat)

FRONT SEAT ASSEMBLY (for TMMK Made Power Seat) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.



1. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
  1. Install the separate type front seat cushion spring assembly.



2. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Driver Side)
  1. Install the 2 front seatback hooks to the lumbar support adjuster assembly.



    B280192
  1. Engage the 2 guides.

  1. Engage the 4 claws to install the lumbar support adjuster assembly.

  1. Connect the connector.



3. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (for Front Passenger Side)
  1. Install the 2 front seatback hooks to the separate type front seatback spring assembly.



    B280140
  1. Engage the 2 guides.

  1. Engage the 4 claws to install the separate type front seatback spring assembly.



4. INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY
  1. Install the front seatback frame sub-assembly with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



5. INSTALL FRONT SEAT CUSHION PANEL SUB-ASSEMBLY (for Driver Side)
  1. Install the front seat cushion panel sub-assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



6. INSTALL FRONT UPPER SEAT TRACK COVER LH
  1. Engage the 2 claws to install the front upper seat track cover LH.



7. INSTALL FRONT UPPER SEAT TRACK COVER RH
  1. Engage the 2 claws to install the front upper seat track cover RH.



8. INSTALL REAR UPPER SEAT TRACK COVER LH (for Front Passenger Side)
  1. Engage the 2 claws to install the rear upper seat track cover LH.



9. INSTALL REAR UPPER SEAT TRACK COVER RH (for Front Passenger Side)
  1. Engage the 2 claws to install the rear upper seat track cover RH.



10. INSTALL FRONT NO. 2 SEAT WIRE
  1. Connect the connectors and engage the wire harness clamps to install the front No. 2 seat wire.



11. INSTALL FRONT SEAT WIRE
  1. Connect the connectors and engage the wire harness clamps to install the front seat wire.



12. INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side)


    B278817
  1. Engage the claw to install the occupant detection ECU.

    NOTICE:
    If the occupant detection ECU has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the occupant detection ECU with a new one.

  1. Connect the 2 connectors.

    NOTICE:
    When installing the occupant detection ECU, be careful that the SRS wiring does not interfere with or is pinched between other parts.



13. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
  1. Engage the clamp to install the seat heater control sub-assembly.

  1. Connect the connector.



14. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)


    B280185
  1. Engage the 2 claws to install the front seat lower cushion shield LH.

  1. Engage the hook as shown in the illustration.

  1. Install the screw.

    Torque:
    0.6 N*m{ 6 kgf*cm , 5 in.*lbf }



15. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)


    B280187
  1. Engage the 2 claws to install the front seat lower cushion shield RH.

  1. Engage the hook as shown in the illustration.

  1. Install the screw.

    Torque:
    0.6 N*m{ 6 kgf*cm , 5 in.*lbf }



16. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Front Passenger Side)
  1. Engage the 2 claws to install the front seat lower cushion shield LH.



17. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Front Passenger Side)

HINT:
Perform the same procedure as for the LH side.



18. INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
  1. Using a tacker, install the front seatback heater assembly to the separate type front seatback cover with 8 new tag pins.



19. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B280132
  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

  1. Engage the 2 fasteners.



20. INSTALL FRONT SEAT AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the front seatback frame sub-assembly is not deformed. If it is, replace it with a new one.

  1. Install the front seat airbag assembly with 2 new nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Engage the 2 clamps.



21. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
  1. Temporarily install the separate type front seatback cover with pad.

  1. Engage the 4 claws to install the 2 front seat headrest supports.

  1. Engage the 2 hooks.

    CAUTION:
    1. For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
    2. Make sure that the strap is not twisted after engage the 2 hooks.
    3. Engage the 2 hooks securely.

  1. Turn back the separate type front seatback cover.

  1. Engage the 2 fasteners.

  1. Engage the hook.



22. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)


    B405025
  1. Using a tacker, install the front seat cushion heater assembly to the separate type front seat cushion cover with 22 new tag pins.



23. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    B280123
  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 12 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seat cushion cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.



24. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
  1. Temporarily install the separate type front seat cushion cover with pad.

  1. Engage each hook.



  1. for Driver Side:



      B280171
    1. Install the separate type front seat cushion cover.



  1. for Front Passenger Side:



      B280193
    1. Install the separate type front seat cushion cover.



    B280156E01
  1. Engage the claw (D) and 3 clamps (C) to install the front seat airbag assembly wire harness.

  1. Engage the clamp (B).

  1. Connect the connector (A).

  1. w/ Seat Heater System:

    1. Connect the connector (E).

    2. Engage the clamp (F).



25. INSTALL LOWER SEAT TRACK RAIL
  1. Install the lower seat track rail.



26. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Seat)


    B380863E02
  1. Install the front seat inner belt assembly LH with the nut.
    Text in Illustration 
    *a
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly LH to overlap the protruding part of the front seat adjuster.

  1. Engage the clamp.

  1. Engage each clamp under the front seat assembly.



27. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Seat)


    B380859E02
  1. Install the front seat inner belt assembly RH with the nut.
    Text in Illustration 
    *a
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly RH to overlap the protruding part of the front seat adjuster.

  1. Engage the clamp.

  1. Connect the connector.



28. INSTALL FRONT SEAT INNER CUSHION SHIELD
  1. Install the front seat inner cushion shield with the 2 screws.

    Torque:
    0.6 N*m{ 6 kgf*cm , 5 in.*lbf }



29. INSTALL FRONT LUMBAR POWER SEAT SWITCH (for Driver Side)
  1. Connect the connector to install the front lumbar power seat switch.



30. INSTALL FRONT POWER SEAT SWITCH
  1. Install the front power seat switch to a new front seat cushion shield with the 3 screws.



31. INSTALL FRONT SEAT CUSHION SHIELD
  1. for Driver Side:

    1. Engage the 4 claws to install the front lumbar power seat switch to the front seat cushion shield.

  1. Connect the front power seat switch connector.

  1. Engage the wire harness clamp.

  1. Engage the 2 claws to install the front seat cushion shield.

  1. Install the screw.

    Torque:
    0.6 N*m{ 6 kgf*cm , 5 in.*lbf }



32. CONNECT SEPARATE TYPE FRONT SEATBACK COVER
  1. Connect the 2 rubber bands of the separate type front seatback cover.



33. INSTALL RECLINING POWER SEAT SWITCH KNOB
  1. Engage the 4 claws to install the reclining power seat switch knob.



34. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
  1. Engage the 4 claws to install the slide and vertical power seat switch knob.



35. INSTALL SEAT ADJUSTER COVER CAP
  1. Install the 2 seat adjuster cover caps.