DTC B2430 LED Headlight LH Circuit Malfunction |
DTC B2431 LED Headlight RH Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B2430 | Any of the following conditions occur after 20 seconds have elapsed since the ignition switch was turned ON:
|
|
| B2431 | Any of the following conditions occur after 20 seconds have elapsed since the ignition switch was turned ON:
|
|

| 1.CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
| Result | Proceed to |
| Both DTC B2430 and B2431 are not output | A |
| Both DTC B2430 and B2431 are output | B |
| DTC B2430 or B2431 is output | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 2.INSPECT H-LP RELAY |
![]() |
Remove the H-LP relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Voltage applied between terminals 1 and 2 | Below 1 Ω |
| *a | Component without harness connected (H-LP Relay) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (BATTERY - H-LP RELAY) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Relay Terminal 2 - Body ground | Always | 11 to 14 V |
| Relay Terminal 5 - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY) |
Disconnect the A91 headlight assembly LH connector.
Disconnect the A95 headlight assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Relay Terminal 3 - A91-1 (LO) | Always | Below 1 Ω |
| Relay Terminal 3 - A95-1 (LO) | Always | Below 1 Ω |
| Relay Terminal 3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Relay Terminal 1 - 3D-12 | Always | Below 1 Ω |
| Relay Terminal 1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
Remove the instrument panel junction block assembly (Click here).
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.

| *a | Component without harness connected (Instrument Panel Junction Block Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
| 3D-12 - MB-15 (HRLY) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - H-LP RELAY) |
Disconnect the A91 or A95 headlight assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A91-1 (LO) - Body ground | Ignition switch off, light control switch in head position | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| A95-1 (LO) - Body ground | Ignition switch off, light control switch in head position | 11 to 14 V |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A91-4 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A95-4 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 9.CHECK HEADLIGHT ASSEMBLY (INPUT VOLTAGE) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A91-2 (S) - Body ground | Ignition switch ON, light control switch in head position | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| A95-2 (S) - Body ground | Ignition switch ON, light control switch in head position | 11 to 14 V |
|
| ||||
| OK | |
| 10.REPLACE HEADLIGHT UNIT |
Replace the headlight unit with a new or known good one (Click here).
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - HEADLIGHT ASSEMBLY) |
Disconnect the I12 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I12-24 (LLEW) - A91-2 (S) | Always | Below 1 Ω |
| I12-24 (LLEW) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| I12-21 (RLEW) - A95-2 (S) | Always | Below 1 Ω |
| I12-21 (RLEW) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||