Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM

THEFT DETERRENT SYSTEM > Security Horn Circuit

for Preparation Click here


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM


B289670E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Horn
    Security horn
    ON / OFF
    -

OK:
The security horn assembly sounds and stops correctly when operated through the intelligent tester.



NG
Go to step 2
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

2.INSPECT SECURITY HORN ASSEMBLY


    B281883E01
  1. Remove the security horn assembly (Click here).

  1. Check the operation of the security horn assembly.

    Standard:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1
    Horn sounds
    Battery negative (-) → Horn body

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD



NG
REPLACE SECURITY HORN ASSEMBLY (Click here)
OK


3.INSPECT S-HORN RELAY


    B256934E02
  1. Remove the S-HORN relay from engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Condition
    Specified Condition
    3 - 5
    10 kΩ or higher
    (when battery voltage is not applied between terminals 1 and 2)
    3 - 5
    Below 1 Ω
    (when battery voltage is applied between terminals 1 and 2)

    Text in Illustration 
    *a
    S-HORN Relay



NG
REPLACE S-HORN RELAY
OK


4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Remove the main body ECU (multiplex network body ECU) (Click here).


    B220554E18


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

  1. Disconnect the 3D instrument panel junction block assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3D-14 - MB-17 (SH)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (BATTERY - S-HORN RELAY)


    B278765E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block and junction block assembly S-HORN relay terminal 1- Body ground
    Always
    11 to 14 V
    Engine room relay block and junction block assembly S-HORN relay terminal 5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Engine room relay block and junction block assembly



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - SECURITY HORN ASSEMBLY)


    B278765E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block and junction block assembly S-HORN relay terminal 3 - A44-1
    Always
    Below 1 Ω
    Engine room relay block and junction block assembly S-HORN relay terminal 3 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Engine room relay block and junction block assembly



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (S-HORN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    B278765E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block and junction block assembly S-HORN relay terminal 2 - 3D-14
    Always
    Below 1 Ω
    Engine room relay block and junction block assembly S-HORN relay terminal 2 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Engine room relay block and junction block assembly



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)