FUEL LID LOCK CONTROL CABLE ASSEMBLY (for RHD) > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat) |
| 3. REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat) |
| 4. REMOVE FRONT DOOR SCUFF PLATE RH |
| 5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 6. REMOVE REAR DOOR SCUFF PLATE RH |
| 7. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH |
| 8. REMOVE LAP BELT OUTER ANCHOR COVER |
| 9. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH |
| 10. REMOVE CENTER PILLAR LOWER GARNISH RH |
| 11. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Disengage the 6 claws and remove the rear door scuff plate LH.
| 12. REMOVE REAR SEAT CUSHION ASSEMBLY |
![]() |
Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
| a | 100 mm (3.94 in.) or less |
w/ Seat Heater System:
Disconnect the connector.
![]() |
Disengage the 2 clamps.
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.
| 13. REMOVE REAR SEAT CUSHION LOCK HOOK |
![]() |
Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.
| 14. REMOVE REAR SIDE SEATBACK ASSEMBLY LH |
Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide LH.
![]() |
Remove the bolt.
Disengage the hook and remove the rear side seatback assembly LH.
| 15. REMOVE LUGGAGE COMPARTMENT FLOOR MAT |
Remove the luggage compartment floor mat.
| 16. REMOVE BAGGAGE HOLDER NET (w/ Partition Net) |
Remove the baggage holder net.
| 17. REMOVE REAR FLOOR FINISH PLATE |
![]() |
Remove the 5 clips.
![]() |
Disengage the 4 clips and remove the rear floor finish plate.
| 18. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
![]() |
Push the pin and remove the No. 1 luggage compartment trim hook.
| *1 | Pin |
| 19. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH |
![]() |
Remove the 3 clips.
Disengage the fastener and remove the luggage compartment inner trim cover LH.
| 20. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
![]() |
Remove the screw.
![]() |
Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.
![]() |
Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.
| 21. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY |
![]() |
Disengage the 2 clamps.
![]() |
Disengage the clamp and disconnect the wire harness.
![]() |
Disengage the 2 clamps and remove the 2 scuff plate clips.
Turn back the floor carpet so that the fuel lid lock control cable sub-assembly can be removed.
![]() |
Remove the 2 pieces of tape that connect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.
| *1 | Tape |
| *2 | Fuel Lid Lock Control Cable Sub-assembly |
| *3 | Luggage Door Lock Control Cable Sub-assembly |
![]() |
Remove the No. 2 noise control plate.
![]() |
Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.
| *1 | Cutout |
| *2 | Guide <A> |
![]() |
Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.
| *1 | Cutout |
| *2 | Guide <B> |
![]() |
Pull out the fuel filler opening lid lock retainer with both guides <B> and <C> aligned with the cutouts.
| *1 | Cutout |
| *2 | Guide <C> |
| *3 | Guide <B> |
![]() |
Disengage the 2 claws and remove the fuel filler opening lid lock retainer.
Disengage the 7 clamps and remove the fuel lid lock control cable sub-assembly.

| *1 | Fuel Lid Lock Control Cable Sub-assembly | *2 | Luggage Door Lock Control Cable Sub-assembly |