LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for RHD) > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat) |
| 3. REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat) |
| 4. REMOVE FRONT DOOR SCUFF PLATE RH |
| 5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 6. REMOVE REAR DOOR SCUFF PLATE RH |
| 7. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH |
| 8. REMOVE LAP BELT OUTER ANCHOR COVER |
| 9. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH |
| 10. REMOVE CENTER PILLAR LOWER GARNISH RH |
| 11. REMOVE REAR SEAT CUSHION ASSEMBLY |
![]() |
Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
| a | 100 mm (3.94 in.) or less |
w/ Seat Heater System:
Disconnect the connector.
![]() |
Disengage the 2 clamps.
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.
| 12. REMOVE REAR SEAT CUSHION LOCK HOOK |
![]() |
Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.
| 13. REMOVE REAR SIDE SEATBACK ASSEMBLY RH |
Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide RH.
![]() |
Remove the bolt.
Disengage the hook and remove the rear side seatback assembly RH.
| 14. REMOVE LUGGAGE COMPARTMENT DOOR COVER |
![]() |
Remove the 13 clips and luggage compartment door cover.
| 15. REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER RH |
| 16. REMOVE LUGGAGE COMPARTMENT FLOOR MAT |
Remove the luggage compartment floor mat.
| 17. REMOVE BAGGAGE HOLDER NET (w/ Partition Net) |
Remove the baggage holder net.
| 18. REMOVE REAR FLOOR FINISH PLATE |
![]() |
Remove the 5 clips.
![]() |
Disengage the 4 clips and remove the rear floor finish plate.
| 19. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
![]() |
Push the pin and remove the No. 1 luggage compartment trim hook.
| *1 | Pin |
| 20. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER RH |
![]() |
Remove the 3 clips.
Disengage the fastener and remove the luggage compartment inner trim cover RH.
| 21. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
![]() |
Remove the screw.
![]() |
Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.
![]() |
Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.
| 22. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY |
![]() |
Disengage the 2 clamps.
![]() |
Disengage the clamp and disconnect the wire harness.
![]() |
Disengage the 2 clamps and remove the 2 scuff plate clips.
Turn back the floor carpet so that the luggage door lock control cable sub-assembly can be removed.
![]() |
Remove the 2 pieces of tape that connect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.
| *1 | Tape |
| *2 | Fuel Lid Lock Control Cable Sub-assembly |
| *3 | Luggage Door Lock Control Cable Sub-assembly |
![]() |
Disengage the guide as shown in the illustration.
![]() |
Disconnect the luggage door lock control cable sub-assembly.
![]() |
Disengage the 2 clamps and disconnect the luggage door lock control cable sub-assembly.
Disengage the 10 clamps and remove the luggage door lock control cable sub-assembly.

| *1 | Luggage Door Lock Control Cable Sub-assembly | *2 | Fuel Lid Lock Control Cable Sub-assembly |