CAMSHAFT > INSTALLATION |
| 1. INSTALL NO. 3 CAMSHAFT |
Apply a light coat of engine oil to the No. 3 camshaft journals and camshaft housing sub-assembly LH.
Install the No. 3 camshaft to the camshaft housing sub-assembly LH.
| 2. INSTALL NO. 4 CAMSHAFT |
Apply a light coat of engine oil to the No. 4 camshaft journals and camshaft housing sub-assembly LH.
Install the No. 4 camshaft to the camshaft housing sub-assembly LH.
| 3. INSTALL CAMSHAFT BEARING CAP (for Bank 2) |
Apply engine oil to the camshaft bearing caps.
![]() |
Make sure of the marks and numbers on the camshaft bearing caps and place them in each proper position and direction.
![]() |
Temporarily tighten the 8 bolts in the order shown in the illustration.
| 4. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH |
![]() |
Make sure that the valve rocker arm is installed as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Lash Adjuster |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
| *a | Seal packing diameter (3.5 to 4.5 mm) |
![]() |
Install the camshaft housing sub-assembly LH and tighten the 13 bolts in the order shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
![]() |
Tighten the 8 bolts in the order shown in the illustration.
| 5. INSTALL CAMSHAFT |
Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly RH.
Install the camshaft to the camshaft housing sub-assembly RH.
| 6. INSTALL NO. 2 CAMSHAFT |
Apply a light coat of engine oil to the No. 2 camshaft journals and camshaft housing sub-assembly RH.
Install the No. 2 camshaft to the camshaft housing sub-assembly RH.
| 7. INSTALL CAMSHAFT BEARING CAP (for Bank 1) |
Apply engine oil to the camshaft bearing caps.
![]() |
Make sure of the marks and numbers on the camshaft bearing caps and place them in each proper position and direction.
![]() |
Temporarily tighten the 8 bearing cap bolts in the order shown in the illustration.
| 8. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH |
![]() |
Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Lash Adjuster |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
| *a | Seal packing diameter (3.5 to 4.5 mm) |
![]() |
Install the camshaft housing sub-assembly RH and tighten the 12 bolts in the order shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
![]() |
Tighten the 8 bolts in the order shown in the illustration.
| 9. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Install the No. 3 chain tensioner assembly with the bolt.
| *1 | Plunger |
| *2 | Pin |
| *a | Push |
While pushing in the tensioner, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold it.
| 10. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2) |
![]() |
Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.
| *1 | Timing Mark |
| *2 | Mark Plate |
Apply a light coat of engine oil to the bolt threads and bolt-seating surface.
Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly installed.
![]() |
Using SST to hold the hexagonal portion of each camshaft, tighten the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Remove the pin from the No. 3 chain tensioner assembly.
| 11. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Install the No. 2 chain tensioner assembly with the bolt.
| *1 | Plunger |
| *2 | Pin |
| *a | Push |
While pushing in the No. 2 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold it.
| 12. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1) |
![]() |
Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.
| *1 | Timing Mark |
| *2 | Mark Plate |
Apply a light coat of engine oil to the bolt threads and bolt-seating surface.
Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly installed.
![]() |
Using SST to hold the hexagonal portion of each camshaft, tighten the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Remove the pin from the No. 2 chain tensioner assembly.
| 13. INSTALL IDLE SPROCKET ASSEMBLY |
![]() |
Apply a light coat of engine oil to the rotating surface of the No. 1 idle gear shaft.
| *1 | Knock Pin |
Temporarily install the No. 1 idle gear shaft and idle sprocket assembly with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block.
Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.
| 14. INSTALL CHAIN SUB-ASSEMBLY |
![]() |
Align the mark plates and timing marks as shown in the illustration and install the chain sub-assembly.
| *1 | Mark Plate |
| *a | Timing Mark |
![]() |
Do not pass the chain sub-assembly over the crankshaft, just temporarily place it on the crankshaft.
![]() |
Turn the camshaft timing gear assembly on bank 1 counterclockwise to tighten the chain sub-assembly between the banks.
| *1 | Mark Plate |
| *a | Turn |
| *b | When the idle sprocket is reused |
| *c | Mark |
| *d | Align |
![]() |
Align the mark plate and timing marks as shown in the illustration and install the chain sub-assembly onto the crankshaft timing sprocket.
| *1 | Mark Plate |
| *a | Timing Mark |
Temporarily tighten the pulley set bolt.
![]() |
Turn the crankshaft clockwise to set it to the RH block bore center line (TDC/compression).
| *1 | Center Line |
| *2 | Timing Mark |
| *3 | Sensor Plate |
| 15. INSTALL CHAIN TENSIONER SLIPPER |
Install the chain tensioner slipper.
| 16. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.
| *1 | Stopper Plate |
| *2 | Plunger |
Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.
![]() |
Install the No. 1 chain tensioner assembly with the 2 bolts.
Remove the hexagon wrench from the No. 1 chain tensioner assembly.
| 17. INSPECT VALVE TIMING |
Check the camshaft timing marks.
Check that each camshaft timing mark is positioned as shown in the illustration.

| *a | Timing Mark | *b | Viewpoint |
![]() |
If the valve timing is misaligned, reinstall the timing chain sub-assembly and No. 2 chain sub-assembly.
Remove the pulley set bolt.
| 18. INSTALL TIMING CHAIN CASE OIL SEAL |
![]() |
Using SST, tap in a new oil seal until its surface is flush with the timing chain case edge.
Apply a light coat of MP grease to the timing chain cover oil seal lip.
| 19. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY |
Apply seal packing in a continuous line to the engine unit as shown in the following illustration.

| *a | Seal Diameter: 3.0 mm or more | ![]() | Seal Packing |
Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

| *a | Dashed line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) | *b | Continuous line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) |
| *c | Alternate long and short dashed line area (Seal packing: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent) | *d | Diagonal line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) |
![]() | Be sure to apply seal packing | - | - |
| Area | Seal Packing Diameter | Application Position from Inside Seal Line |
| Continuous Line Area | 4.5 mm or more (0.177 in.) | 1.0 to 2.0 mm (0.0394 to 0.0787 in.) |
| Alternate Long and Short Dashed Line Area | 3.5 mm or more (0.138 in.) | 2.0 to 3.0 mm (0.0787 to 0.118 in.) |
| Dashed Line Area | 3.5 mm or more (0.138 in.) | 3.0 to 4.0 mm (0.118 to 0.158 in.) |
| Diagonal Line Area | 6.0 mm or more (0.236 in.) | 5.0 mm (0.197 in.) |
![]() |
Install a new gasket.
![]() |
Align the oil pump drive rotor spline and the crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.
| *1 | Drive Rotor Spline |
| *2 | Crankshaft |
Type X:
![]() |
Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.
| *1 | Nut |
| Item | Length |
| Bolt (A) | 40 mm (1.57 in.) |
| Bolt (B) | 55 mm (2.17 in.) |
| Bolt (C) | 25 mm (0.984 in.) |
Type Y:
![]() |
Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.
| *1 | Nut |
| Item | Length |
| Bolt (A) | 40 mm (1.57 in.) |
| Bolt (B) | 55 mm (2.17 in.) |
| Bolt (C) | 28 mm (1.10 in.) |
![]() |
Fully tighten the bolts in this order: Area 1 and Area 2.
| *a | Area 1 |
| *b | Area 2 |
| *c | Area 3 |
| *d | Area 4 |
Fully tighten the bolts and nuts in Area 3.
Fully tighten the bolts in Area 4.
| 20. INSTALL OIL PAN SUB-ASSEMBLY |
Using an E8 "TORX" socket wrench, install the 2 stud bolts.

| *A | Type A | *B | Type B |
| *a | Timing Chain Cover Sub-assembly Side | *b | Cylinder Block Sub-assembly Bottom Side |
| *c | 16 mm (0.630 in.) | *d | 12 mm (0.472 in.) |
| *e | 34 mm (1.34 in.) | - | - |
![]() |
Install 2 new O-rings.
![]() |
Apply seal packing in a continuous line as shown in the illustration.
| *a | Seal Diameter |
![]() |
Install the oil pan sub-assembly with the 16 bolts and 2 nuts.
| *A | Type A |
| *B | Type B |
| *a | Nut |
| 21. INSTALL OIL STRAINER SUB-ASSEMBLY |
![]() |
Using an E6 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.
| *a | Timing Chain Cover |
![]() |
Install a new gasket and the oil strainer sub-assembly with the bolt and 2 nuts.
| *1 | Nut |
| 22. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Using an E6 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.
![]() |
Apply seal packing in a continuous line as shown in the illustration.
| *a | Seal Diameter |
![]() |
Install the No. 2 oil pan sub-assembly with the 16 bolts and 2 nuts.
| *1 | Nut |
| 23. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Apply seal packing as shown in the illustration.
![]() | Seal Packing |
![]() |
Install 3 new gaskets as shown in the illustration.
Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.
![]() |
Install the cylinder head cover sub-assembly with the 12 bolts and a new seal washer.
| 24. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH |
![]() |
Apply seal packing as shown in the illustration.
![]() | Seal Packing |
![]() |
Install 3 new gaskets as shown in the illustration.
Install a new No. 2 cylinder head cover gasket to the cylinder head cover sub-assembly LH.
![]() |
Install the cylinder head cover sub-assembly LH with the 12 bolts and a new seal washer.
| 25. INSTALL WATER INLET HOUSING |
![]() |
Install 2 new O-rings.
![]() |
Install the 2 stud bolts.
![]() |
Install the water inlet housing with the 2 bolts and nut.
| *1 | Nut |
| *2 | Bolt |
Connect the No. 1 water by-pass hose.
Apply adhesive around the drain cock assembly.
Install the drain cock assembly to the water inlet housing.
Install the drain cock plug to the drain cock assembly.
Install a new gasket to the thermostat.
![]() |
Align the thermostat jiggle valve with the upper stud bolt, and insert the thermostat in the water inlet housing.
![]() |
Install the water inlet with the 2 nuts.
| 26. INSTALL NO. 1 FRONT ENGINE MOUNTING BRACKET LH |
![]() |
Using an E8 "TORX" socket wrench, install the 2 stud bolts.
| *1 | Stud Bolt |
Install the No. 1 front engine mounting bracket LH with the 6 bolts.
| 27. INSTALL CRANKSHAFT PULLEY |
Align the pulley set key with the key groove of the pulley, and slide on the pulley.
![]() |
Using SST, install the pulley bolt.
| *a | Hold |
![]() | Turn |
| 28. INSTALL NO. 1 OIL PIPE |
Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.
![]() |
Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the No. 1 oil pipe (on the head cover side) with the union.
| *1 | Oil Pipe Union |
Install a new gasket and temporarily install the No. 1 oil pipe (on the cylinder head side) with the union.
Tighten the oil pipe union (on the head cover side).
Tighten the oil pipe union (on the cylinder head side).
| 29. INSTALL OIL PIPE |
Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.
![]() |
Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side) with the union.
| *1 | Oil Pipe Union |
Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the union.
Install the bolt (A) to the cylinder head.
Tighten the oil pipe union (on the head cover side).
Tighten the oil pipe union (on the cylinder head side).
| 30. INSTALL CRANK POSITION SENSOR |
![]() |
Apply a light coat of engine oil to the O-ring on the crank position sensor.
| *1 | O-ring |
Install the crank position sensor with the bolt.
Connect the crank position sensor connector.
| 31. INSTALL NO. 1 VACUUM SWITCHING VALVE |
Install the No. 1 vacuum switching valve with the bolt.
| 32. INSTALL WATER PUMP PULLEY |
Temporarily install the water pump pulley with the 4 bolts.
Using SST, hold the water pump pulley.
Tighten the 4 bolts.
| 33. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY |
Install the idler pulley cover plate, No. 2 idler pulley sub-assembly and No. 2 idler pulley cover plate with the bolt.
| 34. INSTALL NO. 2 TIMING GEAR COVER |
Install the No. 2 timing gear cover with the 2 bolts.
| 35. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE |
![]() |
Apply a light coat of engine oil to a new O-ring and install it to the engine oil level dipstick guide.
![]() |
Install the engine oil level dipstick guide with the bolt.
| 36. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Temporarily install the V-ribbed belt tensioner assembly with the 5 bolts.
Install the V-ribbed belt tensioner assembly by tightening the bolt 1 and bolt 2 in the order shown in the illustration.
Tighten the other bolts.
| 37. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Install a new gasket as shown in the illustration.
![]() | Engine Front |
![]() |
Install the exhaust manifold sub-assembly LH with the 6 nuts in the order shown in the illustration.
| 38. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
Install the No. 2 exhaust manifold heat insulator with the 3 bolts.
| 39. INSTALL NO. 2 MANIFOLD STAY |
![]() |
Tighten the bolt and nut in the order shown in the illustration.
| 40. INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE |
Install a new O-ring to the No. 2 engine oil level dipstick guide.
Apply a light coat of engine oil to the O-ring.
Push in the No. 2 engine oil level dipstick guide end into the engine oil level dipstick guide.
Install the No. 2 engine oil level dipstick guide with the bolt.
Install the engine oil level dipstick.
| 41. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH |
![]() |
Install a new gasket as shown in the illustration.
![]() | Engine Front |
![]() |
Install the exhaust manifold sub-assembly RH with the 6 nuts in the order shown in the illustration.
| 42. INSTALL INTAKE MANIFOLD |
Set a new gasket on each cylinder head.
Set the intake manifold on the cylinder heads.
Install and tighten the 6 bolts and 4 nuts uniformly in several steps.
| 43. INSTALL NO. 2 ENGINE MOUNTING STAY RH |
Install the No. 2 engine mounting stay RH with the bolt.
| 44. INSTALL IGNITION COIL ASSEMBLY |
Install the 6 ignition coils with the 6 bolts.
Connect the 6 ignition coil connectors.
Connect the 2 wire harness clamps.
Install the nut.
| 45. INSTALL THROTTLE BODY BRACKET |
| Oil Application Prohibited Bolt |
| Bolt for throttle body bracket and cylinder head cover |
Install the throttle body bracket with the bolt.
| 46. INSTALL NO. 1 SURGE TANK STAY |
| Oil Application Prohibited Bolt |
| Bolt for No. 1 surge tank stay and cylinder head cover |
Install the No. 1 surge tank stay with the bolt.
| 47. INSTALL INTAKE AIR SURGE TANK ASSEMBLY |
| Oil Application Prohibited Bolt |
| Intake Air Surge Tank Assembly and Intake Manifold |
| No. 1 Surge Tank Stay and Intake Air Surge Tank Assembly |
| Throttle Body Bracket and Intake Air Surge Tank Assembly |
Install 3 new gaskets to the intake air surge tank assembly.
Temporarily install the intake air surge tank assembly with the 4 bolts and 2 nuts.
![]() |
Using a 5 mm hexagon socket wrench, in several steps, uniformly tighten the 4 bolts and 2 nuts in the order shown in the illustration.
Install the throttle body bracket and No. 1 surge tank stay with the 2 bolts.
Install the vacuum hose clamp with the bolt.
Connect the connector to the intake air control valve assembly.
Connect the 2 water by-pass hoses and fuel vapor feed hose.
Connect the connector and wire harness clamp to the throttle body assembly.
Connect the hose clamp and union to check valve hose.
Connect the ventilation hose.
| 48. INSTALL ENGINE HANGERS |
![]() |
Remove the 4 bolts and 2 engine hangers.
| *1 | No. 1 engine hanger |
| *2 | No. 2 engine hanger |
| *a | Bank 1 |
| *b | Bank 2 |
| 49. REMOVE ENGINE STAND |
| 50. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
Using SST, hold the crankshaft pulley.
Clean the 8 bolts and 8 bolt holes.
![]() |
Install the front drive plate spacer.
![]() |
Install the drive plate and ring gear sub-assembly and rear drive plate spacer onto the crankshaft.
| *1 | Drive Plate |
| *2 | Rear Spacer |
![]() | Transaxle Side |
![]() |
Apply adhesive to 2 or 3 threads of each bolt.
| *1 | Adhesive |
![]() |
In several steps, uniformly install and tighten the 8 bolts in the sequence shown in the illustration.
| 51. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY |