FRONT BUMPER (for TMC, TMMR Made) > REASSEMBLY |
| 1. INSTALL FRONT BUMPER SIDE RETAINER LH |
![]() |
Engage the 2 claws.
Install the front bumper side retainer LH with the bolt and screw.
| 2. INSTALL FRONT BUMPER SIDE RETAINER RH |
| 3. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY |
![]() |
Install the front bumper reinforcement sub-assembly with the 6 bolts.
Engage the 5 clamps.
| 4. INSTALL FRONT BUMPER ENERGY ABSORBER |
![]() |
Engage the 2 guides to install the front bumper energy absorber.
| 5. INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY |
Engage the 24 claws.

Install the lower radiator grille sub-assembly to the front bumper cover with the 4 screws.

| 6. INSTALL LOWER FRONT BUMPER COVER |
![]() |
Engage the hook.
| *a | Hook |
Engage the 4 claws to install the lower front bumper cover.
| 7. INSTALL FRONT BUMPER HOLE COVER LH |
![]() |
Engage the 6 claws to install the front bumper hole cover LH
| 8. INSTALL FRONT BUMPER HOLE COVER RH |
| 9. INSTALL RADIATOR GRILLE BRACKET |
![]() |
Engage the guide.
Install the radiator grille bracket with the clip.
| 10. INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY |
![]() |
Engage the 3 claws and guide to install the radiator grille emblem assembly to the radiator grille emblem base.
![]() |
Engage the 4 claws and 2 guides.
Install the radiator grille emblem assembly with radiator grille emblem base with the 2 screws.
| 11. INSTALL UPPER RADIATOR GRILLE MOULDING LH |
![]() |
Engage the 3 claws.
Install the upper radiator grille moulding LH with the screw.
| 12. INSTALL UPPER RADIATOR GRILLE MOULDING RH |
| 13. INSTALL RADIATOR GRILLE SUB-ASSEMBLY |
![]() |
Engage the 8 claws.
Install the radiator grille sub-assembly with the 2 clips.
| 14. INSTALL NO. 2 RADIATOR GRILLE BRACKET |
![]() |
Engage the guide.
Install the No. 2 radiator grille bracket with the 2 screws.
| 15. INSTALL FRONT FENDER LINER RETAINER |
![]() |
Engage the claw to install the front fender liner retainer.
| 16. INSTALL NO. 4 ENGINE ROOM WIRE (w/o TOYOTA Parking Assist-sensor System) |
![]() |
Engage the clamp to install the No. 4 engine room wire.
| 17. INSTALL NO. 4 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System) |
![]() |
Engage the clamp to install the No. 4 engine room wire.
| 18. INSTALL FOG LIGHT ASSEMBLY LH |
Engage the 2 guides to temporarily install the fog light assembly.
Install the fog light assembly with the screw.
Connect the connector.
| 19. INSTALL FOG LIGHT ASSEMBLY RH |
| 20. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System) |
![]() |
Engage the 2 claws to install the No. 1 ultrasonic sensor retainer to the front bumper assembly.
| *a | Cutout |
| *b | Protrusion |
| 21. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System) |
Engage the 2 claws to install the No. 1 ultrasonic sensor to the No. 1 ultrasonic sensor retainer.
Connect the connector.
| 22. INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System) |
![]() |
Engage the 8 clamps to install the headlight cleaner hose.
| 23. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System) |
Engage the guide as shown in the illustration.

While pushing the tab indicated by the arrow (A), engage the claw to install the headlight washer actuator sub-assembly.
![]() |
Push the headlight cleaner actuator clamp as shown in the illustration.
![]() |
Install the headlight cleaner clamp.
Connect the headlight cleaner hose.
| 24. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System) |
| 25. INSTALL HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System) |
![]() |
Engage the claw to install the headlight washer nozzle sub-assembly.
| 26. INSTALL HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System) |