Home › Vehicle Interior › DOOR LOCK › TRANSMITTER BATTERY (w/o Smart Entry and Start System)

TRANSMITTER BATTERY (w/o Smart Entry and Start System) > REPLACEMENT

for Preparation Click here



1. REMOVE TRANSMITTER HOUSING COVER (for Type A)

NOTICE:
Take extra care when handling these precision electronic components.



    B386453E01
  1. Insert a precision screwdriver into the gap, and turn the screwdriver to remove the transmitter housing cover.
    Text in Illustration 
    *a
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



2. REMOVE DOOR CONTROL TRANSMITTER PACKING (for Type A)


    B386454E01
  1. Insert a precision screwdriver into the door control transmitter packing and turn the screwdriver to remove the door control transmitter packing.
    Text in Illustration 
    *a
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE TRANSMITTER BATTERY (for Type A)


    B386455E01
  1. Insert a precision screwdriver into the gap and gently remove the transmitter battery (lithium battery: CR1620).
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    1. Do not push the terminals with your finger.
    2. Do not forcibly pry up the transmitter battery as the terminals may be damaged.
    3. Do not touch the transmitter battery with wet hands. Moisture may cause rust.
    4. Do not touch or move any components inside the transmitter. It may interfere with proper operation.
    5. When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter from being damaged.

    HINT:
    Tape the screwdriver tip before use.



4. REMOVE TRANSMITTER HOUSING COVER (for Type B)


    B213771E02
  1. Using a precision screwdriver with its tip wrapped in protective tape, pry open the transmitter housing cover.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Do not forcibly pry the cover.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY (for Type B)


    B213773E02
  1. Using a precision screwdriver with its tip wrapped in protective tape, remove the door control transmitter module set sub-assembly from the transmitter housing case.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Handle each part with care as they are delicate electrical parts.

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE TRANSMITTER BATTERY (for Type B)


    B279946
  1. Twist the coin in the direction of the arrow in the illustration, and remove the transmitter battery cover.



    B250771
  1. Remove the transmitter battery (lithium battery: CR2016).

    NOTICE:
    1. Do not push the terminals with your finger.
    2. Do not forcibly pry up the transmitter battery. The terminals may be damaged.
    3. Do not touch the transmitter battery with wet hands. Water may cause rust.
    4. Do not touch or move any components inside the transmitter. It may interfere with proper operation.
    5. When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter from being damaged.



7. INSTALL TRANSMITTER BATTERY (for Type A)


    B386456
  1. Install a new transmitter battery (lithium battery: CR1620) with the positive (+) side facing upward, as shown in the illustration.

    NOTICE:
    1. Do not bend the transmitter battery electrode during installation.
    2. Keep the inside of the transmitter housing cover interior free of dust and oil.
    3. When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter from being damaged.



8. INSTALL DOOR CONTROL TRANSMITTER PACKING (for Type A)


    B386457
  1. Install the door control transmitter packing as shown in the illustration.



9. INSTALL TRANSMITTER HOUSING COVER (for Type A)


    B386458
  1. Install the transmitter housing cover as shown in the illustration.



10. INSTALL TRANSMITTER BATTERY (for Type B)


    B250772
  1. Install a transmitter battery (lithium battery: CR2016) with the positive (+) side facing upward, as shown in the illustration.

    NOTICE:
    1. Do not bend the transmitter battery electrode during installation.
    2. Keep the inside of the transmitter housing cover interior free of dust and oil.
    3. When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the electrical transmitter from being damaged.



    B283995
  1. Install the cover.



11. INSTALL DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY (for Type B)


    B213774
  1. Install the door control transmitter module set sub-assembly into the transmitter housing case.



12. INSTALL TRANSMITTER HOUSING COVER (for Type B)


    B213770
  1. Install the transmitter housing cover to the transmitter housing case.

  1. Check that the transmitter LED illuminates when the switch is pressed.

    OK:
    Transmitter LED illuminates when switch is pressed.