Home › Engine / Hybrid System ยท 2AR-FE › LUBRICATION › OIL AND OIL FILTER

OIL AND OIL FILTER > REPLACEMENT

for Preparation Click here


CAUTION:
  1. Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.
  3. In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.



1. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Clean the oil pan drain plug and install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



2. REMOVE OIL FILTER CAP ASSEMBLY


    A204919E06
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose



    A196672
  1. Remove the oil filter drain plug from the oil filter cap.



    A196673E04
  1. Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Valve
    *2
    Cap
    *3
    O-ring
    *4
    Pipe

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.



    A196674
  1. Check that the oil is drained from the oil filter. Then disconnect the pipe as shown in the illustration and remove the O-ring.



    A215914E02
  1. Using SST, remove the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    SST
    09228-06501  

    NOTICE:
    Do not remove the oil filter bracket clip.



    A196675E07
  1. Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    Oil Filter Cap
    *3
    O-ring

    NOTICE:
    Be sure to remove the O-ring by hand, without using any tools, to prevent damage to the O-ring groove.



3. INSTALL OIL FILTER CAP ASSEMBLY
  1. Clean the inside of the oil filter cap, threads and O-ring groove.



    A196675E07
  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    Oil Filter Cap
    *3
    O-ring

  1. Set a new oil filter element into the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.



    A194917E02
  1. Using SST, tighten the oil filter cap.
    Text in Illustration 
    *a
    No Clearance

    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Make sure that the oil filter is installed securely as shown in the illustration.



    A194918E04
  1. Apply a small amount of engine oil to a new O-ring, and install it to the oil filter cap.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

  1. Install the oil filter drain plug.

    Torque:
    13 N*m{ 127 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Be careful that the O-ring does not get caught between any surrounding parts.



4. ADD ENGINE OIL
  1. Add new oil.

    Standard Oil Grade:

    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
    1. 0W-20
    1. 5W-20
    1. 5W-30
    1. 10W-30
    API grade SL, SM or SN multigrade engine oil
    1. 15W-40
    1. 20W-50


    Standard Capacity:

    Item
    Specified Condition
    Drain and refill (with oil filter change)
    4.4 liters (4.6 US qts, 3.9 Imp. qts)
    Drain and refill (without oil filter change)
    4.0 liters (4.2 US qts, 3.5 Imp. qts)
    Dry fill
    5.3 liters (5.6 US qts, 4.7 Imp. qts)

  1. Install the oil filler cap.



5. INSPECT FOR OIL LEAK


6. INSPECT ENGINE OIL LEVEL
  1. Warm up and stop the engine, and then wait 5 minutes.

  1. Check that the oil level is between the low level mark and full level mark on the engine oil level dipstick.
    If the level is low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill the engine with oil to above the full level mark.