Home › Engine / Hybrid System ยท 6AR-FSE › LUBRICATION › OIL AND OIL FILTER

OIL AND OIL FILTER > REPLACEMENT

for Preparation Click here


CAUTION:
  1. Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Wear protective clothing and gloves. Avoid contact with used engine oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.
  3. In order to protect the environment, dispose of used engine oil and used engine oil filters at designated disposal sites only.



1. DRAIN ENGINE OIL
  1. Remove the oil filler cap sub-assembly.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Clean the oil pan drain plug.

  1. Install a new gasket to the oil pan drain plug.

  1. Install the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



2. REMOVE OIL FILTER CAP ASSEMBLY


    A189717E01
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *a
    Pipe
    *b
    Hose



    A196672
  1. Remove the oil filter drain plug from the oil filter cap assembly.



    A196673E08
  1. Insert the pipe with hose into the oil filter cap assembly.
    Text in Illustration 
    *1
    Oil Filter Cap Assembly
    *2
    O-ring
    *a
    Valve
    *b
    Hose

    NOTICE:
    Be sure to insert the pipe with the O-ring installed to the oil filter cap assembly.

    HINT:
    Place the hose end into a container before draining the engine oil from the hose.



    A196674
  1. Make sure that the engine oil is completely drained, and remove the pipe with hose and O-ring.

    HINT:
    Pull the pipe with hose as shown in the illustration to remove it.



    A215914E02
  1. Using SST, remove the oil filter cap assembly.
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    SST
    09228-06501  

    NOTICE:
    Do not remove the oil filter bracket clip.



    A196675E07
  1. Remove the oil filter element and O-ring from the oil filter cap assembly.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    Oil Filter Cap Assembly
    *3
    O-ring

    NOTICE:
    Do not use any tools to remove the O-ring in order to prevent the oil filter cap assembly from being damaged. Be sure to remove it by hand.



3. INSTALL OIL FILTER CAP ASSEMBLY
  1. Clean the inside of the oil filter cap assembly, the threads and O-ring groove.



    A337618E01
  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.
    Text in Illustration 
    *1
    O-ring
    *a
    Correct
    *b
    Incorrect

    NOTICE:
    1. Be sure to install the O-ring in the proper location, otherwise engine oil may leak.
    2. Do not twist the O-ring.

  1. Set a new oil filter element in the oil filter cap assembly.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and install the oil filter cap assembly.

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.



    A281504E02
  1. Using SST, tighten the oil filter cap assembly.
    Text in Illustration 
    *1
    Oil Filter Cap Assembly
    *2
    O-ring
    *3
    Oil Filter Bracket
    *a
    No Gap

    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    1. After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.
    2. Do not cross thread the oil filter cap assembly.



    A194918E04
  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Remove any dirt or foreign matter from the installation surface.

  1. Install the oil filter drain plug to the oil filter cap assembly.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.



4. ADD ENGINE OIL
  1. Add clean engine oil and install the oil filler cap sub-assembly.

    Standard Oil Grade:

    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "Energy-Conserving", SM "Energy- Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
    1. 0W-20
    1. 5W-20
    1. 5W-30
    1. 10W-30
    API grade SL, SM or SN multigrade engine oil
    1. 15W-40


    Standard Capacity:

    Item
    Specified Condition
    Drain and refill with oil filter change
    4.4 liters (4.6 US qts, 3.9 Imp. qts)
    Drain and refill without oil filter change
    4.0 liters (4.2 US qts, 3.5 Imp. qts)
    Dry fill
    5.3 liters (5.6 US qts, 4.7 Imp. qts)



5. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no engine oil leaks from the area that was worked on.



6. INSPECT ENGINE OIL LEVEL
  1. Warm up and stop the engine, then wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the engine oil level dipstick.
    If the level is low, check for engine oil leaks and add engine oil to the full level mark.

    NOTICE:
    Do not fill to above the full level mark.