CAMSHAFT
Part Tightened
| N*m
| kgf*cm
| ft.*lbf
|
Camshaft timing exhaust gear assembly x No. 2 camshaft
| 85
| 867
| 63
|
No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap x Camshaft housing sub-assembly and cylinder head sub-assembly
| 27
| 275
| 20
|
No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap x Camshaft housing sub-assembly
| 16
| 163
| 12
|
Camshaft timing gear bolt x Camshaft
| Type A
| 120
| 1224
| 89
|
Type B
| 95
| 969
| 70
|
No. 1 chain tensioner assembly x Cylinder block sub-assembly
| 10
| 102
| 7
|
Timing chain cover plate x Timing chain cover sub-assembly
| 10
| 102
| 7
|
EGR valve bracket x Camshaft housing sub-assembly
| 21
| 214
| 15
|
Fuel hose bracket x EGR valve bracket
| 13
| 133
| 10
|
Engine wire x Engine assembly
| Nut (A)
| 9.8
| 100
| 87 in.*lbf
|
Nut (B) and Bolt
| 8.0
| 82
| 71 in.*lbf
|
ENGINE ASSEMBLY
Part Tightened
| N*m
| kgf*cm
| ft.*lbf
|
No. 1 engine hanger x Cylinder head sub-assembly
| 43
| 438
| 32
|
No. 2 engine hanger x Cylinder head sub-assembly
| 43
| 438
| 32
|
Engine mounting bracket RH x Cylinder block sub-assembly and stiffening crankcase assembly
| 54
| 551
| 40
|
Drive shaft bearing bracket x Cylinder block sub-assembly
| 64
| 650
| 47
|
Engine mounting insulator LH x Automatic transaxle assembly
| 95
| 969
| 70
|
Front engine mounting insulator x Front engine mounting bracket
| 87
| 887
| 64
|
Engine mounting insulator RH x Engine mounting bracket RH
| 95
| 969
| 70
|
Front engine mounting insulator x Front frame assembly
| 58
| 591
| 43
|
Engine mounting insulator RH x Front frame assembly
| 99
| 1010
| 73
|
Engine mounting insulator LH x Front frame assembly
| 99
| 1010
| 73
|
Frame side rail plate RH and Frame side rail plate LH x Vehicle body
| Bolt (A)
| 85
| 867
| 63
|
Bolt (B) and Nut
| 32
| 329
| 24
|
Front suspension member rear brace RH and Front suspension member rear brace LH x Vehicle body
| Bolt (A)
| 85
| 867
| 63
|
Bolt (B) and Nut
| 32
| 329
| 24
|
Engine moving control rod and engine moving control rod bracket x Vehicle body and engine mounting bracket RH
| 38
| 387
| 28
|
Engine moving control rod and No. 3 engine mounting stay RH x Engine moving control rod bracket
| without SST
| 52
| 530
| 38
|
with SST
| 33
| 337
| 24
|
No. 2 engine mounting stay RH x Engine moving control rod bracket and camshaft housing sub-assembly
| 38
| 387
| 28
|
Earth wire x Engine moving control rod bracket and vehicle body
| 8.0
| 82
| 71 in.*lbf
|
No. 1 air cleaner bracket x Battery carrier
| 8.0
| 82
| 71 in.*lbf
|
Engine wire x Engine room relay block assembly
| 8.5
| 87
| 75 in.*lbf
|
Engine wire x Vehicle body
| 8.5
| 87
| 75 in.*lbf
|
Battery clamp x Vehicle body
| Bolt
| 9.0
| 92
| 80 in.*lbf
|
Nut
| 3.5
| 36
| 31 in.*lbf
|
Cable x Positive (+) battery terminal
| 6.5
| 66
| 58 in.*lbf
|
Air cleaner case sub-assembly x No. 1 air cleaner bracket
| 5.0
| 51
| 44 in.*lbf
|
Inlet air cleaner assembly x Vehicle body
| 8.0
| 82
| 71 in.*lbf
|
Cable x Negative (-) battery terminal
| 6.5
| 66
| 58 in.*lbf
|
ENGINE UNIT
Part Tightened
| N*m
| kgf*cm
| ft.*lbf
|
Stiffening crankcase stud bolt x Stiffening crankcase assembly
| Stud bolt (A)
| 9.5
| 97
| 84 in.*lbf
|
Stud bolt (B)
| 4.0
| 41
| 35 in.*lbf
|
Engine balancer assembly x Stiffening crankcase assembly
| 24
| 245
| 18
|
Stiffening crankcase assembly x Cylinder block sub-assembly
| Bolt (A)
| 24
| 245
| 18
|
except Bolt (A)
| 43
| 438
| 32
|
No. 1 oil pan baffle plate x Stiffening crankcase assembly and engine balancer assembly
| 10
| 102
| 7
|
Oil level sensor bracket x Stiffening crankcase assembly
| 10
| 102
| 7
|
Oil strainer sub-assembly x Stiffening crankcase assembly and engine balancer assembly
| 9.0
| 92
| 80 in.*lbf
|
Oil pan sub-assembly x Stiffening crankcase assembly
| 10
| 102
| 7
|
Oil pan drain plug x Oil pan sub-assembly
| 40
| 408
| 30
|
Camshaft housing stud bolt x Camshaft housing sub-assembly
| 6.5
| 66
| 58 in.*lbf
|
No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap x Camshaft housing sub-assembly
| 16
| 163
| 12
|
No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap x Camshaft housing sub-assembly and cylinder head sub-assembly
| 27
| 275
| 20
|
Oil pipe sub-assembly x No. 4 camshaft bearing cap
| 10
| 102
| 7
|
Camshaft timing exhaust gear assembly x No. 2 camshaft
| 85
| 867
| 63
|
Camshaft timing gear bolt x Camshaft
| Type A
| 120
| 1224
| 89
|
Type B
| 95
| 969
| 70
|
No. 1 chain vibration damper x Cylinder head sub-assembly and cylinder block sub-assembly
| 21
| 214
| 15
|
Chain tensioner slipper x Cylinder head sub-assembly
| 21
| 214
| 15
|
No. 1 chain tensioner assembly x Cylinder block sub-assembly
| 10
| 102
| 7
|
Timing chain guide x No. 1 camshaft bearing cap
| 21
| 214
| 15
|
Case separator x Cylinder head cover case sub-assembly
| 10
| 102
| 7
|
Cylinder head cover sub-assembly x Camshaft housing sub-assembly
| 12
| 122
| 9
|
Crankshaft pulley x Crankshaft
| 260
| 2651
| 192
|
No. 1 ventilation case x Cylinder block sub-assembly
| 21
| 214
| 15
|
Engine cover joint x Cylinder head cover sub-assembly and camshaft housing sub-assembly
| 10
| 102
| 7
|
Bracket x Cylinder head cover sub-assembly
| 10
| 102
| 7
|
Stud bolt x Water inlet housing
| Stud bolt (A), (B)
| 4.4
| 45
| 39 in.*lbf
|
Stud bolt (C)
| 4.0
| 41
| 35 in.*lbf
|
Water inlet housing x Cylinder block sub-assembly
| 43
| 439
| 32
|
No. 1 water by-pass pipe x Water inlet housing and cylinder block sub-assembly
| 10
| 102
| 7
|
V-ribbed belt tensioner assembly x Water inlet housing
| 21
| 214
| 15
|
No. 1 compressor mounting bracket x Cylinder block sub-assembly and stiffening crankcase assembly
| 21
| 214
| 15
|
Engine oil level dipstick guide x Water inlet housing
| 10
| 102
| 7
|
Exhaust manifold converter sub-assembly (TWC: Front Catalyst) x Cylinder head sub-assembly
| 62
| 632
| 46
|
Intake manifold x Cylinder head sub-assembly
| 28
| 286
| 21
|