INSTRUMENT PANEL SAFETY PAD (for TMC, TMMR Made) > DISASSEMBLY |
| 1. REMOVE NO. 1 INSTRUMENT PANEL PIN |
Remove the 4 screws <D> and 4 No. 1 instrument panel pins.

| 2. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY |
![]() |
Remove the 2 screws.
![]() |
Lean the instrument panel safety pad assembly and disengage the 3 hooks.
![]() |
Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad assembly.
| 3. REMOVE NO. 1 HEATER TO REGISTER DUCT (except LHD with Ion Generator) |
![]() |
Remove the clip.
Remove the 3 screws <D> and No. 1 heater to register duct.
| 4. REMOVE HEATER TO REGISTER DUCT ASSEMBLY (for LHD with Ion Generator) |
![]() |
Remove the clip.
Remove the 3 screws <D>.
Disengage the heater to register duct assembly from the ion generator assembly, to remove the heater to register duct.
| 5. REMOVE NO. 3 HEATER TO REGISTER DUCT (for LHD) |
![]() |
Remove the clip.
Remove the 3 screws <D> and No. 3 heater to register duct.
| 6. REMOVE HEATER TO REGISTER DUCT ASSEMBLY (for RHD) |
![]() |
Remove the clip.
Remove the 3 screws <D>.
Disengage the heater to register duct assembly from the ion generator assembly, to remove the heater to register duct.
| 7. REMOVE ION GENERATOR SUB-ASSEMBLY WITH BRACKET (w/ Ion Generator) |
![]() |
Remove the 3 screws and ion generator sub-assembly with bracket.
| *A | for LHD |
| *B | for RHD |
| 8. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT |
![]() |
Remove the screw <D>.
Disengage the 2 claws to remove the No. 1 side defroster nozzle duct.
| 9. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT |
![]() |
Remove the screw <D>.
Disengage the 2 claws to remove the No. 2 side defroster nozzle duct.
| 10. REMOVE ANTENNA CORD SUB-ASSEMBLY |
for LHD:
Disengage the 8 clamps and remove the antenna cord sub-assembly.

for RHD:
Disengage the 10 clamps and remove the antenna cord sub-assembly.

| 11. REMOVE DEFROSTER NOZZLE ASSEMBLY |
![]() |
Remove the 3 screws <D>.
Disengage the 2 guides to remove the defroster nozzle assembly.
| 12. REMOVE NAVIGATION ANTENNA ASSEMBLY (w/ Navigation Antenna) |
![]() |
Remove the 2 screws.
Disengage the 2 clamps and remove the navigation antenna assembly.
| 13. REMOVE NO. 2 HEATER TO REGISTER DUCT |
![]() |
Remove the 2 screws <D> and No. 2 heater to register duct.
| 14. REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY |
![]() |
Remove the 2 screws <D>.
Apply protective tape to the areas shown in the illustration.

| *1 | Protective Tape | - | - |
Disengage the 6 clips for No. 2 instrument panel garnish sub-assembly lower part as shown in the illustration.
Using a moulding remover, disengage the 8 clips to remove the No. 2 instrument panel garnish sub-assembly as shown in the illustration.