Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

DTC    B2658    Short in Sensor with Motor Power Supply Circuit

for Preparation Click here


DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.

DTC Code
DTC Detection Condition
Trouble Area
B2658
Problem with the voltage supplied to the position control sensor.
  1. Front power seat switch LH (w/ Memory)
  2. Separate type front seat cushion assembly
  3. Separate type front seatback assembly
  4. Wire harness or connector

WIRING DIAGRAM


B270910E41


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2658 is not output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - SLIDE MOTOR)
  1. Disconnect the e12 front power seat switch LH (w/ Memory) connector.

  1. Disconnect the e8 slide motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    e12-5 (SSRS) - e8-2
    Always
    Below 1 Ω
    e12-1 (SGND) - e8-3
    Always
    Below 1 Ω
    e12-5 (SSRS) - e12-1 (SGND)
    Always
    10 kΩ or higher
    e12-5 (SSRS) - Body ground
    Always
    10 kΩ or higher
    e12-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK FRONT POWER SEAT SWITCH LH (W/ MEMORY) (SLIDE MOTOR CIRCUIT)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    e8-2 - e8-3
    Sliding switch on
    4.8 to 5.1 V



NG
REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - FRONT VERTICAL MOTOR)
  1. Disconnect the e9 front vertical motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    e12-3 (SSFV) - e9-2
    Always
    Below 1 Ω
    e12-1 (SGND) - e9-3
    Always
    Below 1 Ω
    e12-3 (SSFV) - e12-1 (SGND)
    Always
    10 kΩ or higher
    e12-3 (SSFV) - Body ground
    Always
    10 kΩ or higher
    e12-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK FRONT POWER SEAT SWITCH LH (W/ MEMORY) (FRONT VERTICAL MOTOR CIRCUIT)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    e9-2 - e9-3
    Front vertical switch on
    4.8 to 5.1 V



NG
REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - LIFTER MOTOR)
  1. Disconnect the e10 lifter motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    e12-4 (SSRL) - e10-2
    Always
    Below 1 Ω
    e12-1 (SGND) - e10-3
    Always
    Below 1 Ω
    e12-4 (SSRL) - e12-1 (SGND)
    Always
    10 kΩ or higher
    e12-4 (SSRL) - Body ground
    Always
    10 kΩ or higher
    e12-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK FRONT POWER SEAT SWITCH LH (W/ MEMORY) (LIFTER MOTOR CIRCUIT)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    e10-2 - e10-3
    Lifter switch on
    4.8 to 5.1 V



NG
REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)
OK


8.REPLACE SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY
  1. Replace the separate type front seat cushion assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2658 is not output.



NG
Go to step 9
OK

END (SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY WAS DEFECTIVE) 

9.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - RECLINING MOTOR)
  1. Disconnect the e12 front power seat switch LH (w/ Memory) connector.

  1. Disconnect the g3 reclining motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    e12-11 (SSRR) - g3-2
    Always
    Below 1 Ω
    e12-1 (SGND) - g3-3
    Always
    Below 1 Ω
    e12-11 (SSRR) - e12-1 (SGND)
    Always
    10 kΩ or higher
    e12-11 (SSRR) - Body ground
    Always
    10 kΩ or higher
    e12-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK FRONT POWER SEAT SWITCH LH (W/ MEMORY) (RECLINING MOTOR CIRCUIT)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    g3-2 - g3-3
    Reclining switch on
    4.8 to 5.1 V



NG
REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)
OK


11.REPLACE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
  1. Replace the separate type front seatback assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2658 is not output.



NG
REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)
OK

END (SEPARATE TYPE FRONT SEATBACK ASSEMBLY WAS DEFECTIVE)