Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH

WIPER SWITCH > INSPECTION

for Preparation Click here



1. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (W/O AUTO WIPER SWITCH ASSEMBLY)


  1. for LHD:



      E171721E31
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      I32-1 (+S) - I32-3 (+1)
      OFF
      Below 1 Ω
      INT
      I32-2 (+B) - I32-3 (+1)
      MIST
      LO
      I32-2 (+B) - I32-4 (+2)
      HI
      Front Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      I31-4 (EW) - I31-7 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)
      If the result is not as specified, replace the windshield wiper switch assembly.



2. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (W/ AUTO WIPER SYSTEM)


  1. for LHD:



      E227241E01
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      I32-3 (+1) - I32-1 (+S)
      OFF
      Below 1 Ω
      I32-3 (+1) - I32-2 (+B)
      MIST
      LO
      I32-2 (+B) - I32-4 (+2)
      HI
      I32-8 (AUTO) - I32-9 (E)
      AUTO
      Front Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      I31-4 (EW) - I31-7 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher
      Adjusting Ring* 
      Tester Connection
      Switch Condition
      Specified Condition
      I32-7 (VR1) - I32-6 (VR2)
      P1
      209 to 231 Ω
      P2
      114 to 126 Ω
      P3
      58.9 to 65.1 Ω
      P4
      Below 1 Ω

      HINT:
      *: The rain sensor sensitivity can be adjusted by the windshield wiper switch adjusting ring.

      Text in Illustration 
      *1
      Windshield Wiper Switch Assembly (Adjusting Ring Position)
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)
      If the result is not as specified, replace the windshield wiper switch assembly.



  1. for RHD:



      E227242E01
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      I32-2 (+1) - I32-4 (+S)
      OFF
      Below 1 Ω
      I32-2 (+1) - I32-3 (+B)
      MIST
      LO
      I32-3 (+B) - I32-1 (+2)
      HI
      I32-7 (AUTO) - I32-6 (E)
      AUTO
      Front Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      I31-7 (EW) - I31-4 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher
      Adjusting Ring* 
      Tester Connection
      Switch Condition
      Specified Condition
      I32-9 (VR1) - I32-8 (VR2)
      P1
      209 to 231 Ω
      P2
      114 to 126 Ω
      P3
      58.9 to 65.1 Ω
      P4
      Below 1 Ω

      HINT:
      *: The rain sensor sensitivity can be adjusted by the windshield wiper switch adjusting ring.

      Text in Illustration 
      *1
      Windshield Wiper Switch Assembly (Adjusting Ring Position)
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)
      If the result is not as specified, replace the windshield wiper switch assembly.