DTC B2603 Tilt and Telescopic Manual Switch Circuit Malfunction |
| DTC No. | Detection Condition | Trouble Area |
| B2603 | When operating the tilt and telescopic switch, an abnormal voltage value is sent to the multiplex tilt and telescopic ECU. |
|

| 1.READ VALUE USING INTELLIGENT TESTER (TILT UP/DOWN SWITCH, TELESCOPIC SHORT/LONG SWITCH) |
![]() |
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Check the tilt and telescopic manual switch. Enter the following menus: Body / Tilt & Telescopic / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Telesco Short Switch | Input state of telescopic contract switch/ OFF or ON | OFF: Telescopic contract switch not activated ON: Telescopic contract switch activated | - |
| Telesco Long Switch | Input state of telescopic extend switch/ OFF or ON | OFF: Telescopic extend switch not activated ON: Telescopic extend switch activated | - |
| Tilt Down Switch | Input state of tilt down switch/ OFF or ON | OFF: Tilt down switch not activated ON: Tilt down switch activated | - |
| Tilt Up Switch | Input state of tilt up switch/ OFF or ON | OFF: Tilt up switch not activated ON: Tilt up switch activated | - |
| *a | Tilt Up |
| *b | Tilt Down |
| *c | Telescopic Extend (Long) |
| *d | Telescopic Contract (Short) |
|
| ||||
| OK | |
| 2.CONFIRM DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
| Result | Proceed to |
| DTC is output. | A |
| DTC is not output. | B |
|
| ||||
| A | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH) |
Disconnect the I15 multiplex tilt and telescopic ECU connector.
Disconnect the I26 tilt and telescopic switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I15-5 (VC) - I26-1 (VC) | Always | Below 1 Ω |
| I15-18 (MSW) - I26-3 (MSW) | ||
| I15-5 (VC) - Body ground | 10 kΩ or higher | |
| I15-18 (MSW) - Body ground |
|
| ||||
| OK | |
| 4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE) |
![]() |
Reconnect the I15 multiplex tilt and telescopic ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| I15-5 (VC) - I15-18 (MSW) | Engine switch on (IG) | 4.9 to 5.1 V |
| *a | Component with harness connected (Multiplex Tilt and Telescopic ECU) |
|
| ||||
| OK | |
| 5.CHECK TILT AND TELESCOPIC SWITCH |
![]() |
Remove the tilt and telescopic switch (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1(VC) - 3(MSW) | Tilt up | 342 to 378 Ω |
| Tilt down | 1890.5 to 2089.5 Ω | |
| Telescopic contract | 750.5 to 829.5 Ω | |
| Telescopic extend | 152 to 168 Ω |
| *a | Component without harness connected (Tilt and Telescopic Switch) |
|
| ||||
| OK | ||
| ||