Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > USB Audio System Recognition/Play Error

for Preparation Click here


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio and display receiver assembly. This diagnostic procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM


for LHD (w/ Wireless Charger System)

E277817E42


for LHD (w/o Wireless Charger System)

E277817E43


for RHD

E277817E44


INSPECTION PROCEDURE

HINT:
  1. When a large amount of data is in a USB device, it may take a while to begin playback.
  2. When using a USB device, files that are protected by copyright cannot be played.
  3. When files are not played in the sorted order, perform the following procedure before inspection.
    1. Add numbers in front of the file names.
    2. Put the files in a folder and copy the folder data to the USB device.

1.CHECK USB DEVICE OR "iPod"
  1. Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.

  1. Check if playable files are present on the USB device or "iPod".

    HINT:
    Refer to System Description for playable files (Click here).

  1. Check if the USB device is a compatible format or "iPod" is a compatible version.

    HINT:
    Refer to System Description for compatible formats and versions (Click here).

    Result:
    Result
    Proceed to
    No playable files exist, or incompatible device format or version.
    A
    Playable files exist, and compatible device format or version.
    B



B
Go to step 2
A

END (USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES EXIST) 

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
  1. Disconnect the I205 radio and display receiver assembly connector. (w/ Display Signal Line)

  1. Disconnect the I156 radio and display receiver assembly connector. (w/o Display Signal Line)

  1. Disconnect the I204 No. 1 stereo jack adapter assembly connector. (for RHD with Display Signal Line), (for LHD without Wireless Charger System)

  1. Disconnect the I207 No. 1 stereo jack adapter assembly connector. (for LHD with Wireless Charger System)

  1. Disconnect the I146 No. 1 stereo jack adapter assembly connector. (for RHD without Display Signal Line)



    E277837E30
  1. Measure the resistance according to the value(s) in the table below. (w/ Display Signal Line)

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I204-1 (UPI) - I205-1 (UPO)
    Always
    Below 1 Ω
    I204-2 (UDO-) - I205-2 (UDO-)
    Always
    Below 1 Ω
    I204-3 (UDO+) - I205-3 (UDO+)
    Always
    Below 1 Ω
    I204-4 (UJSG) - I205-4 (UPSG)
    Always
    Below 1 Ω
    I204-5 (UJSS) - I205-5 (USG1)
    Always
    Below 1 Ω
    I204-1 (UPI) - Body ground
    Always
    10 kΩ or higher
    I204-2 (UDO-) - Body ground
    Always
    10 kΩ or higher
    I204-3 (UDO+) - Body ground
    Always
    10 kΩ or higher
    I204-4 (UJSG) - Body ground
    Always
    10 kΩ or higher
    I204-5 (UJSS) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



    E277837E31
  1. Measure the resistance according to the value(s) in the table below. (for LHD with Wireless Charger System)

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I207-1 (UPI) - I205-1 (UPO)
    Always
    Below 1 Ω
    I207-2 (UDO-) - I205-2 (UDO-)
    Always
    Below 1 Ω
    I207-3 (UDO+) - I205-3 (UDO+)
    Always
    Below 1 Ω
    I207-4 (UJSG) - I205-4 (UPSG)
    Always
    Below 1 Ω
    I207-5 (UJSS) - I205-5 (USG1)
    Always
    Below 1 Ω
    I207-1 (UPI) - Body ground
    Always
    10 kΩ or higher
    I207-2 (UDO-) - Body ground
    Always
    10 kΩ or higher
    I207-3 (UDO+) - Body ground
    Always
    10 kΩ or higher
    I207-4 (UJSG) - Body ground
    Always
    10 kΩ or higher
    I207-5 (UJSS) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



    E291450E10
  1. Measure the resistance according to the value(s) in the table below. (for RHD without Display Signal Line)

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I146-1 (UPI) - I156-1 (USV1)
    Always
    Below 1 Ω
    I146-2 (UDO-) - I156-2 (US1-)
    Always
    Below 1 Ω
    I146-3 (UDO+) - I156-3 (US1+)
    Always
    Below 1 Ω
    I146-4 (UJSG) - I156-4 (UGD1)
    Always
    Below 1 Ω
    I146-5 (UJSS) - I156-5 (USG1)
    Always
    Below 1 Ω
    I146-1 (UPI) - Body ground
    Always
    10 kΩ or higher
    I146-2 (UDO-) - Body ground
    Always
    10 kΩ or higher
    I146-3 (UDO+) - Body ground
    Always
    10 kΩ or higher
    I146-4 (UJSG) - Body ground
    Always
    10 kΩ or higher
    I146-5 (UJSS) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



    E277837E32
  1. Measure the resistance according to the value(s) in the table below. (for LHD without Display Signal Line)

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I204-1 (UPI) - I156-1 (UPO)
    Always
    Below 1 Ω
    I204-2 (UDO-) - I156-2 (UDO-)
    Always
    Below 1 Ω
    I204-3 (UDO+) - I156-3 (UDO+)
    Always
    Below 1 Ω
    I204-4 (UJSG) - I156-4 (UPSG)
    Always
    Below 1 Ω
    I204-5 (UJSS) - I156-5 (USG1)
    Always
    Below 1 Ω
    I204-1 (UPI) - Body ground
    Always
    10 kΩ or higher
    I204-2 (UDO-) - Body ground
    Always
    10 kΩ or higher
    I204-3 (UDO+) - Body ground
    Always
    10 kΩ or higher
    I204-4 (UJSG) - Body ground
    Always
    10 kΩ or higher
    I204-5 (UJSS) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
  1. Disconnect the I204 No. 1 stereo jack adapter assembly connector. (for RHD with Display Signal Line), (for LHD without Wireless Charger System)

  1. Disconnect the I207 No. 1 stereo jack adapter assembly connector. (for LHD with Wireless Charger System)

  1. Disconnect the I146 No. 1 stereo jack adapter assembly connector. (for RHD without Display Signal Line)



    E277838E04
  1. Measure the voltage according to the value(s) in the table below. (for RHD with Display Signal Line), (for LHD without Wireless Charger System)

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I204-1 (UPI) - I204-4 (UJSG)
    Ignition switch ACC
    5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



    E277838E03
  1. Measure the voltage according to the value(s) in the table below. (for LHD with Wireless Charger System)

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I207-1 (UPI) - I207-4 (UJSG)
    Ignition switch ACC
    5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



    E226479E72
  1. Measure the voltage according to the value(s) in the table below. (for RHD without Display Signal Line)

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I146-1 (UPI) - I146-4 (UJSG)
    Ignition switch ACC
    5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
  1. Delete all files in the USB device or "iPod" and format/restore it.

  1. Save the data again and check if it can be played on the in-vehicle device.

    NOTICE:
    Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that a backup of the music data is available before performing this operation.

    OK:
    Malfunction disappears.



NG
Go to step 5
OK

END 

5.REPLACE USB DEVICE OR "iPod"
  1. Turn the ignition switch off.

    HINT:
    When this malfunction occurs, it is necessary to turn the ignition switch off to make it possible for the vehicle to recognize a new device when it is connected.

  1. Turn the ignition switch to ACC.

  1. Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
  1. If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.
  2. Refer to System Description for compatible formats and versions (Click here).


NEXT


6.CHECK USB DEVICE OR "iPod"
  1. Check if a USB device or "iPod" is recognized by the radio and display receiver assembly, and if information such as track, artist and album names is displayed on the screen.

    OK:
    USB device or "iPod" is recognized properly and the information is displayed on the screen.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE