EGR VALVE > REMOVAL |
| 1. DRAIN ENGINE COOLANT (for Engine) |
![]() |
Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.
| *1 | Engine Under Cover LH |
| *a | Hose |
Loosen the radiator drain cock plug.
![]() |
Remove the radiator cap sub-assembly. Then drain the engine coolant.
| *1 | Radiator Cap Sub-assembly |
| *2 | Radiator Drain Cock Plug |
Disconnect the hose from the radiator drain cock.
| 2. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY |
![]() |
Disengage the 3 grommets to remove the No. 1 engine cover sub-assembly.
| 3. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE |
![]() |
Slide the clip and disconnect the ventilation hose from the cylinder head cover sub-assembly.
Disengage the ventilation hose clamp.
![]() |
Disconnect the mass air flow meter sub-assembly connector.
Disengage the wire harness clamp.
![]() |
Disconnect the union to connector tube hose from the air cleaner hose sub-assembly.
Disengage the 2 air cleaner cap clamps and 2 guides.
![]() |
Loosen the hose clamp and remove the air cleaner cap with air cleaner hose from the throttle body with motor assembly.
| 4. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.
| 5. REMOVE AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Disconnect the wire harness clamp.
Remove the 2 bolts and air cleaner case sub-assembly.
| 6. REMOVE FUEL PUMP PROTECTOR |
![]() |
Remove the 2 bolts and fuel pump protector from the cylinder head cover sub-assembly.
| 7. REMOVE EGR PIPE CONNECTOR |
![]() |
Remove the 4 bolts, nut and EGR pipe connector from the exhaust manifold converter sub-assembly (TWC: Front Catalyst), EGR cooler assembly and cylinder block sub-assembly.
![]() | Bolt |
![]() | Nut |
![]() |
Remove the 2 EGR cooler gaskets from the EGR pipe connector.
| 8. REMOVE NO. 2 EGR PIPE |
![]() |
Disengage the 2 wire harness clamps from the No. 2 EGR pipe.
![]() |
Remove the 4 bolts and No. 2 EGR pipe from the EGR valve assembly and intake manifold.
![]() |
Remove the No. 2 EGR pipe gasket from the EGR valve assembly.
![]() |
Remove the EGR inlet gasket from the intake manifold.
| 9. DISCONNECT ENGINE WIRE |
![]() |
Remove the 2 bolts and disconnect the 2 earth wires from the EGR valve bracket.
| *a | Fuel Pump Sub-assembly Connector |
| *b | Ignition Coil Assembly Connector |
| *c | Camshaft Position Sensor Connector |
![]() | Bolt |
![]() | Nut |
Remove the nut.
Disconnect the 2 camshaft position sensor connectors.
Disconnect the ignition coil assembly connector.
Disconnect the fuel pump sub-assembly connector.
Disengage the clamp.
![]() |
Remove the bolt.
Disconnect the engine coolant temperature sensor connector.
| 10. REMOVE EGR VALVE WITH COOLER ASSEMBLY |
![]() |
Disconnect the EGR valve assembly connector.
![]() |
Remove the engine cover joint and separate the fuel hose bracket from the EGR valve bracket.
![]() |
Remove the 4 bolts and 2 EGR valve brackets.
![]() |
Disengage the water hose from the hose clamp.
![]() |
Slide the clip and disconnect the water hose sub-assembly from the EGR cooler assembly.
![]() |
Slide the clip and disconnect the No. 2 water by-pass hose from the EGR valve assembly.
| *1 | No. 2 Water By-pass Hose |
| *2 | No. 3 Water By-pass Hose |
| *3 | No. 4 Water By-pass Hose |
Slide the clip and disconnect the No. 3 water by-pass hose from the EGR cooler assembly.
Slide the clip and disconnect the No. 4 water by-pass hose from the EGR cooler assembly.
![]() |
Remove the 2 nuts and EGR valve with cooler assembly from cylinder head sub-assembly.
![]() |
Remove the No. 2 EGR pipe gasket from the EGR valve assembly.
| 11. REMOVE EGR VALVE ASSEMBLY |
![]() |
Slide the clip and disconnect the No. 1 water by-pass hose from the EGR valve assembly.
![]() |
Remove the 2 nuts and EGR valve assembly from the EGR cooler assembly.
![]() |
Remove the EGR valve gasket from the EGR valve assembly.