Home › Steering › STEERING COLUMN › STEERING PAD SWITCH

STEERING PAD SWITCH > INSPECTION

for Preparation Click here



1. INSPECT STEERING PAD SWITCH ASSEMBLY (for Radio Receiver Type)


  1. Measure the resistance according to the value(s) in the table below.


    E314833E01

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HO) - Terminal-A
    Always
    Below 2.5 Ω
    11 (AU1) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Up (LH) switch pushed
    Below 2.5 Ω
    Down (LH) switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    10 (AU2) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    MODE/HOLD switch pushed
    Below 2.5 Ω
    3 (+DP2) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Back switch pushed
    Below 2.5 Ω
    Up (RH) switch pushed
    313 to 345 Ω
    Down (RH) switch pushed
    950 to 1050 Ω
    Page switch pushed
    2955 to 3265 Ω
    2 (+DP) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Enter switch pushed
    Below 2.5 Ω

    HINT:
    If the result is not as specified, replace the steering pad switch assembly.


    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch Assembly)
    *b
    Volume+
    *c
    Volume-
    *d
    MODE/HOLD
    *e
    Up (LH)
    *f
    Down (LH)
    *g
    Back
    *h
    Page
    *i
    Up (RH)
    *j
    Down (RH)
    *k
    Enter
    *l
    Terminal-A



  1. Check the illumination.


    E314834E01


    1. Connect a positive (+) lead from the battery to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.

    2. Check that the switch illumination illuminates.

      OK:
      The steering pad switch illumination illuminates.

      HINT:
      If the result is not as specified, replace the steering pad switch assembly.


      Text in Illustration 
      *a
      Component without harness connected
      (Steering Pad Switch Assembly)
      -
      -



2. INSPECT STEERING PAD SWITCH ASSEMBLY (except Radio Receiver Type)


  1. Measure the resistance according to the value(s) in the table below.


    E314831E01

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z3-1 (HO) - Terminal-A
    Always
    Below 2.5 Ω
    z3-11 (AU1) - z3-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Up (LH) switch pushed
    Below 2.5 Ω
    Down (LH) switch pushed
    313 to 345 Ω
    Volume+ switch pushed
    950 to 1050 Ω
    Volume- switch pushed
    2955 to 3265 Ω
    z3-10 (AU2) - z3-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    MODE/HOLD switch pushed
    Below 2.5 Ω
    On hook switch pushed
    313 to 345 Ω
    Off hook switch pushed
    950 to 1050 Ω
    Voice switch pushed*1
    2955 to 3265 Ω
    z3-9 (AU3) - z3-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Enter (LH) switch pushed
    Below 2.5 Ω
    Back (LH) switch pushed
    313 to 345 Ω
    Right switch pushed
    950 to 1050 Ω
    Left switch pushed
    2955 to 3265 Ω
    z3-3 (+DP2) - z3-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Back (RH) switch pushed
    Below 2.5 Ω
    Up (RH) switch pushed
    313 to 345 Ω
    Down (RH) switch pushed
    950 to 1050 Ω
    Page switch pushed
    2955 to 3265 Ω
    z3-2 (+DP) - z3-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    Enter (RH) switch pushed
    Below 2.5 Ω
    z3-6 (SUP) - SR-2 (SUP)*2
    Always
    Below 2.5 Ω
    z3-7 (ECC) - SR-7 (ECC)*2
    Always
    Below 2.5 Ω
    z3-12 (SDN) - SR-3 (SDN)*2
    Always
    Below 2.5 Ω

    1. *1: w/ Voice Switch
    2. *2: w/ Shift Paddle Switch

    HINT:
    If the result is not as specified, replace the steering pad switch assembly.


    Text in Illustration 
    *A
    w/ Voice Switch
    *B
    w/ Shift Paddle Switch
    *a
    Component without harness connected
    (Steering Pad Switch Assembly)
    *b
    Volume+
    *c
    Volume-
    *d
    Back (LH)
    *e
    MODE/HOLD
    *f
    Up (LH)
    *g
    Down (LH)
    *h
    Left
    *i
    Right
    *j
    Enter (LH)
    *k
    Off hook
    *l
    On hook
    *m
    Voice
    *n
    Back (RH)
    *o
    Up (RH)
    *p
    Down (RH)
    *q
    Page
    *r
    Enter (RH)
    *s
    Terminal-A
    -
    -



  1. Check the illumination.


    E314832E01


    1. Connect a positive (+) lead from the battery to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.

    2. Check that the switch illumination illuminates.

      OK:
      The steering pad switch illumination illuminates.

      HINT:
      If the result is not as specified, replace the steering pad switch assembly.


      Text in Illustration 
      *a
      Component without harness connected
      (Steering Pad Switch Assembly)
      -
      -