SMART ENTRY AND START SYSTEM (for Entry Function) > CUSTOMIZE PARAMETERS |
| 1. CUSTOMIZE SMART ENTRY AND START SYSTEM (for Entry Function) |
Customizing with the intelligent tester
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body or Entry & Start / Utility / Customize / Wireless Door Lock, Entry & Start or Warning.
Select the setting by referring to the table below.
| Display | Default | Content | Setting | Relevant ECU |
| Hazard Answer Back | ON | When the doors are locked by entry function, the hazard warning lights flash once. When the doors are unlocked by entry function, the hazard warning lights flash twice. | OFF or ON | Main body ECU (multiplex network body ECU) |
| Open Door Warning | ON | The buzzer sounds when the lock sensor on the door outside handle assembly is touched to perform entry lock with a door open. | OFF or ON | Main body ECU (multiplex network body ECU) |
| Auto Lock Time | 30 s | Function that regulates the interval between unlocking and automatic relocking of doors. | 30 s, 60 s or 120 s | Main body ECU (multiplex network body ECU) |
| Wireless Buzzer Resp* | ON | Function that sounds the answer-back buzzer when an entry lock or unlock operation is performed. | OFF or ON | Main body ECU (multiplex network body ECU) |
| Wireless Buzzer Vol* | Level 5 | Buzzer answer back volume | Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level0 | Main body ECU (multiplex network body ECU) |
| Display | Default | Content | Setting | Relevant ECU |
| Park Wait Time (Waiting time to permit unlocking door after locking) | 2.5s | Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed. | 0.5s, 1.5s, 2.5s or 5s | Certification ECU (smart key ECU assembly) |
| Ignition Available Area (Entry ignition available area) | All | Function that sets the area that the key must be in before the engine switch can be operated. | Front or All | Certification ECU (smart key ECU assembly) |
| Trunk Open Mode | ON | Function that opens the luggage compartment door when the driver has the electrical key transmitter sub-assembly and presses the luggage door opening switch assembly. | OFF or ON | Certification ECU (smart key ECU assembly) |
| Door Unlock Mode2* | All | Function that chooses the doors to be operated by entry unlock operation. | All or Driver | Certification ECU (smart key ECU assembly) |
| Auto Entry Cancel SW | OFF | Function that enables or disables the smart entry and start system. | OFF or ON | Certification ECU (smart key ECU assembly) |
| Touch Activation Over Threshold | Active | The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed. | Active or Not Active | Certification ECU (smart key ECU assembly) |
| Engine Start Indicator | ON | Function that turns the smart warning light on the combination meter assembly on or off. | OFF or ON | Certification ECU (smart key ECU assembly) |
| Display | Default | Content | Setting | Relevant ECU |
| Key Low Battery Warning (Warn when key battery becomes weak) | ON | Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more. | OFF or ON | Certification ECU (smart key ECU assembly) |
Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type))
Turn the engine switch on (IG).
Enter the following menus: MENU /Setup / Vehicle / Vehicle customization / Door lock settings.
Select the setting by referring to the table below.
| Display | Default | Content | Setting | Relevant ECU |
| Select doors to unlock | All Doors | Function that sets which doors are unlocked by the entry unlock function. | All Doors or Driver's Door | Certification ECU (smart key ECU assembly) |
| Entry and start system | On | Function that enables or disables the smart entry and start system. | On or Off | Certification ECU (smart key ECU assembly) |
Customizing with the multi-display (w/ Navigation System (for Radio and Display Type))
Turn the engine switch on (IG).
Enter the following menus: SETUP / Vehicle / Vehicle customization / Door lock settings.
Select the setting by referring to the table below.
| Display | Default | Content | Setting | Relevant ECU |
| Select doors to unlock | All Doors | Function that sets which doors are unlocked by the entry unlock function. | All Doors or Driver's Door | Certification ECU (smart key ECU assembly) |
| Entry and start system | On | Function that enables or disables the smart entry and start system. | On or Off | Certification ECU (smart key ECU assembly) |
Customizing with the multi-display (w/ Audio and Visual System)
Turn the engine switch on (IG).
Enter the following menus: MENU or APPS / Vehicle / Vehicle customization / Door lock settings.
Select the setting by referring to the table below.
| Display | Default | Content | Setting | Relevant ECU |
| Select doors to unlock | All Doors | Function that sets which doors are unlocked by the entry unlock function. | All Doors or Driver's Door | Certification ECU (smart key ECU assembly) |
| Entry and start system | On | Function that enables or disables the smart entry and start system. | On or Off | Certification ECU (smart key ECU assembly) |
Entry unlock mode switching function (manual operation) (w/ Driver Door Entry Function)
The following entry unlock modes can be selected when using the entry unlock mode switching function.
When customizing through manual operation:
| Currently Selected Mode | Answer-back (Wireless Buzzer) | Answer-back (Buzzer in Combination Meter Assembly) |
| All door unlock mode | Buzzer sounds twice (short beeps) | Buzzer sounds once |
| Driver door unlock mode | Buzzer sounds 3 times (short beeps) | Buzzer sounds once |

Entry cancel function (manual operation)
The following functions are disabled when the smart entry and start system is canceled.
When canceling the system through manual operation:
Perform the following procedure to restore the smart entry and start system to the active state from the canceled state.