SMART ENTRY AND START SYSTEM (for Start Function) > OPERATION CHECK |
| OPERATION DESCRIPTION |
Push-button start function:
When the key is in a detection area inside the vehicle and the brake pedal is depressed, the engine is started by pressing the engine switch.
When the key is in a detection area inside the vehicle and the brake pedal is not depressed, the power source mode is changed by pressing the engine switch. The power source mode changes in the following order every time the engine switch is pressed: off → on (ACC) → on (IG) → off.
After getting into the vehicle while carrying the key when the engine switch is off, if the engine switch is pressed while not depressing the brake pedal, the power source mode changes to on (ACC).
After getting into the vehicle while carrying the key when the engine switch is off, if the engine switch is pressed 2 times without depressing the brake pedal, the power source mode changes to on (IG).
![]() |
After getting into the vehicle while carrying the key when the engine switch is off, if the brake pedal is depressed while the shift lever is in P or N, the smart warning light is displayed.
The engine starts if the engine switch is pressed when the smart warning light is displayed.
| *a | Smart Warning Light Displayed |
Changing the power source mode when the key does not operate correctly due to wave interference or key battery depletion:
Unlock the door using the built-in mechanical key and get into the vehicle while carrying the key.
While depressing the brake pedal, and facing the logo side of the key towards the engine switch, hold the key near the engine switch.
A buzzer in the combination meter assembly sounds and the power source mode changes to on (IG). Pressing the engine switch without depressing the brake pedal turns the power source mode from on (IG) to off.
Starting the engine when the key does not operate correctly due to wave interference or key battery depletion:
Unlock the door using the built-in mechanical key and get into the vehicle while carrying the key.
While depressing the brake pedal with the shift lever in P or N*, while facing the logo side of the key towards the engine switch, hold the key near the engine switch.
A buzzer in the combination meter assembly sounds, the power source mode changes to on (IG) and the smart warning light is displayed.
Press the engine switch with the brake pedal depressed to start the engine.
| CHECK PUSH-BUTTON START FUNCTION |
Check the push-button start function:
Get into the vehicle while carrying the key with the engine switch off. With the shift lever in P, check that the smart warning light is displayed when the brake pedal is depressed. Then check that the engine starts when the engine switch is pressed after the smart warning light is displayed.
While the brake pedal is released and the key is being carried, check that the power source mode changes in the following order when the engine switch is pressed: off → on (ACC) → on (IG) → off.
With the shift lever in P, check that the steering lock operates when a door is opened.
![]() |
Check the push-button start function operation range for the front side. Place the key in either of the two locations making sure that the key is oriented as shown in the illustration, and then check that the engine can be started.
| *A | for Type A |
| *B | for Type B |
| *a | Inspection Point |
![]() |
Check the push-button start function operation range for the rear side. Place the key in either of the two locations making sure that the key is oriented as shown in the illustration, and then check that the engine can be started.
| *A | for Type A |
| *B | for Type B |
| *a | Inspection Point |
| Check transmitter battery saving function |
Check the transmitter battery saving function:
Press the unlock button of the electrical key transmitter sub-assembly twice while pressing the lock button and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.
Check that the smart entry and start system does not operate while in transmitter battery saving mode.
| CHECK POWER SOURCE MODE CHANGING FUNCTION |
Check the engine switch.
Check that the power source mode changes according to the chart below.
| Shift Position | Brake Pedal | Power Source Mode when Engine Switch Pressed |
| P | Released | Off → on (ACC) → on (IG) → off |
| P | Released | Engine running → off |
| P | Released | On (ACC)*1 → off |
| P | Depressed | Off → engine starts |
| P | Depressed | On (ACC) → engine starts |
| P | Depressed | On (IG) → engine starts |
| P | Depressed | Engine running → off |
| P | Depressed | On (ACC)*1 → off |
| N | Released | Off → on (ACC) → on (IG) (after power source mode changes to on (IG), power source mode changes between on (IG) and on (ACC) every time engine switch is pressed) |
| N | Released | Engine running → on (ACC) |
| N | Depressed | Off → engine starts*2 |
| N | Depressed | On (ACC) → engine starts*2 |
| N | Depressed | On (IG) → engine starts*2 |
| N | Depressed | Engine running → on (ACC) |
| Not P or N | Released | Off → on (ACC) → on (IG) (after power source mode changes to on (IG), power source mode changes between on (IG) and on (ACC) every time engine switch is pressed) |
| Not P or N | Released | Engine running → on (ACC) |
| Not P or N | Depressed | Off → on (IG) |
| Not P or N | Depressed | On (ACC) → on (IG) |
| Not P or N | Depressed | Engine running → on (ACC) |
| CHECK POWER SOURCE MODE INDICATION |
![]() |
Check the smart warning.
| *a | Power ON display |
| *b | Smart Warning Light display |
| Power Source Mode | Multi-information Display |
| Off (Excluding condition in which the engine can be started) | Off |
| On (ACC) (Excluding condition in which the engine can be started) | "Power ON" displayed |
| On (IG) (Excluding condition in which the engine can be started) | "Power ON" displayed |
| Condition in which engine can be started*1 | Smart Warning Light displayed |
| Engine started | Off |