AUTOMATIC TRANSAXLE FLUID > REPLACEMENT |
| 1. REPLACE AUTOMATIC TRANSAXLE FLUID |
Lift the vehicle. [*1]
Remove the front wheel opening extension pad LH, engine under cover LH and front fender apron seal LH.
![]() |
Remove the refill plug and gasket from the automatic transaxle assembly. [*2]
![]() |
Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle assembly. [*3]
| *1 | No. 1 Transmission Oil Filler Tube |
| *2 | Overflow Plug |
| *3 | Hexagon Socket Wrench |
![]() |
Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle oil pan sub-assembly and drain the automatic transaxle fluid. [*4]
| *1 | No. 1 Transmission Oil Filler Tube |
| *2 | Hexagon Socket Wrench |
| *a | Overflow Plug Hole |
![]() |
Measure the amount of fluid drained. [*5]
Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle oil pan sub-assembly. [*6]
![]() |
Temporarily install the gasket and the overflow plug. [*7]
![]() |
Add fluid to the refill hole using the same amount of fluid drained in step [*5]. [*8]
![]() |
Temporarily install the gasket and refill plug to avoid fluid spillage. [*9]
Lower the vehicle. [*10]
Start the engine. [*11]
Slowly move the shift lever from P to D, then back to P (keep the shift lever in each position for approximately 3 seconds). [*12]
Allow the engine to idle for 30 seconds to warm it up. [*13]
Turn the ignition switch off. [*14]
Repeat steps [*1] to [*14].
Repeat steps [*1] to [*10].
| 2. ADJUST FLUID TEMPERATURE (for Using the intelligent tester) |
Connect the intelligent tester to the DLC3 with the ignition switch off.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1
Select the Data List menu: A/T Oil Temperature 1
Select the Active Test menu: Connect the TC and TE1 / ON
Check the ATF temperature.
Depress and hold the brake pedal.
Start the engine.
Slowly move the shift lever from P to D, then back to P (keep the shift lever in each position for approximately 3 seconds).
![]() |
While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.
Check that the D shift indicator comes on for 2 seconds.
Move the shift lever from N to P.
Release the brake pedal.
Select the Active Test menu: Connect the TC and TE1 / OFF
![]() |
Warm up the engine with the engine idling until the fluid temperature reaches the fluid level adjustment temperature [35 to 45°C (95 to 113°F)].
| Below Fluid Level Adjustment Temperature | Fluid Level Adjustment Temperature | Above Fluid Level Adjustment Temperature |
| 35°C or less (95°F or less) | 35 to 45°C (95 to 113°F) | 45°C or more (113°F or more) |
| Shift Indicator (D) Turned off | Shift Indicator (D) Turned on | Shift Indicator (D) Blinking |
| *a | Turned Off |
| *b | Turned On |
| *c | Blinking |
| 3. ADJUST FLUID TEMPERATURE (for not Using the intelligent tester) |
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.
| *1 | DLC3 |
Depress and hold the brake pedal.
Start the engine.
Slowly move the shift lever from P to D, then back to P.
![]() |
While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.
Check that the D shift indicator comes on for 2 seconds.
Move the shift lever from N to P.
Release the brake pedal.
Remove SST from terminals 13 (TC) and 4 (CG).
![]() |
Allow the engine to idle until the D shift indicator comes on again.
| Below Fluid Level Adjustment Temperature | Fluid Level Adjustment Temperature | Above Fluid Level Adjustment Temperature |
| 35°C or less (95°F or less) | 35 to 45°C (95 to 113°F) | 45°C or more (113°F or more) |
| Shift Indicator (D) Turned off | Shift Indicator (D) Turned on | Shift Indicator (D) Blinking |
| *a | Turned Off |
| *b | Turned On |
| *c | Blinking |
| 4. ADJUST FLUID LEVEL |
Lift the vehicle.
![]() |
Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket.
| *1 | No. 1 Transmission Oil Filler Tube |
| *2 | Overflow Plug |
| *3 | Hexagon Socket Wrench |
Check the amount of fluid that comes out of the overflow plug hole.
![]() |
If the amount of fluid that comes out of the overflow plug hole is large, wait until the fluid flow slows and only drips come out. [*1]
![]() |
If no fluid comes out of the overflow plug hole, remove the refill plug and gasket. Then add fluid through the refill hole until fluid comes out of the over flow plug hole. Wait until the fluid flow slows and only drips come out. [*2]
![]() |
Install the overflow plug with a new gasket.
| *1 | No. 1 Transmission Oil Filler Tube |
| *2 | Overflow Plug |
| *3 | Hexagon Socket Wrench |
![]() |
Install the refill plug with a new gasket.
Lower the vehicle.
Turn the ignition switch off.
Remove the intelligent tester from the DLC3 (when using the intelligent tester).
| 5. REBUILD WORK |
Lift the vehicle.
Clean each part.
Check for fluid leaks.
Install the front wheel opening extension pad LH, engine under covers LH and front fender apron seal LH.
Lower the vehicle.