Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > CUSTOMIZE PARAMETERS



1. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Tilt & Telescopic / Utility / Customize..

    5. Select the setting by referring to the table below.

      Tilt & Telescopic 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Autoaway/Return function
      ON
      Turn the auto away/return function
      ON/OFF
      Multiplex tilt and telescopic ECU



2. CUSTOMIZE TOYOTA PARKING ASSIST-SENSOR SYSTEM
  1. Customizing with the intelligent tester

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the clearance sonar main switch on.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Body / Clearance Sonar / Utility / Customize.

    6. Select the setting by referring to the table below.

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Rr Sensor Onset Range
      Wide
      Sets the buzzer activation range for the rear center sensors.
      Narrow or Wide
      1. Narrow: 600 mm (23.6 in.)
      2. Wide: 1000 mm (39.4 in.) (Pole)
      3. Wide: 1500 mm (59.1 in.) (Wall)
      Clearance warning ECU assembly
      Keep Sense Buzzer
      Avail
      Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds.
      Not Avail or Avail
      1. Not Avail: Not Available
      2. Avail: Available
      Clearance warning ECU assembly
      Fr & Rr Buzzer Volume
      M2
      Changes the buzzer volume setting.
      L, M1, M2, M3 or H
      1. L: Low volume
      2. M1: Medium low volume
      3. M2: Medium volume
      4. M3: Medium high volume
      5. H: High volume
      Clearance warning ECU assembly

      Sensor 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Sensor Condition N
      Avail
      Makes the front sensors available when the shift lever is in N.
      Not Avail or Avail
      1. Not Avail: Not Available
      2. Avail: Available
      Clearance warning ECU assembly
      Reverse Range Front Sensor
      F
      Changes the operation setting for the front sensors when the shift lever is in R.
      F or F Stop
      1. F: Front sensors are available
      2. F Stop: Front sensors are not available
      Clearance warning ECU assembly
      Non P/R Range Rear Sensor
      R Stop
      Changes the operation setting for the rear sensors when the shift lever is in any position other than P or R.
      R, Rcrn or R Stop
      1. R: All rear sensors are available
      2. Rcrn: Rear corner sensors are available
      3. R Stop: All rear sensors are not available
      Clearance warning ECU assembly



3. CUSTOMIZE POWER DOOR LOCK CONTROL SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Utility / Customize / Door Lock.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Unlock Key Twice
      OFF
      Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlocks all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Auto Lock*
      ON
      Function that locks all doors when the vehicle speed reaches a certain level.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Auto Lock/Shift*
      OFF
      Function that locks all doors when the shift lever is moved out of P with the ignition switch ON and all doors closed.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Auto Unlock/Shift*
      OFF
      Function that unlock all doors when the shift lever is moved to P from any position other than P with the ignition switch ON.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      All Unlock/Open-Close*
      OFF
      Function that unlocks the other doors when the driver door is opened within 10 seconds after the ignition switch is turned off.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Trunk Link with Door Lock
      ON
      Function that opens the luggage compartment door when the luggage electrical key switch is pressed and all doors are unlocked using the entry unlock function, wireless door unlock function, mechanical key or door control switch.
      OFF or ON
      Main body ECU (Multiplex network body ECU)

      1. *: w/ Auto Lock Function

  1. Customizing with the Multi-display (w/ Navigation System (for Navigation Receiver Type))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Speed sensitive auto locking*
      On
      Function that locks all doors when the vehicle speed reaches a certain level.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto ;ock by shift from P*
      Off
      Function that locks all doors when the shift lever is moved out of P with the ignition switch ON and all doors closed.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto unlock by shift to P*
      Off
      Function that unlock all doors when the shift lever is moved to P from any position other than P with the ignition switch ON.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto unlock by driver door*
      Off
      Function that unlocks the other doors when the driver door is opened within 10 seconds after the ignition switch is turned off.
      On or Off
      Main body ECU (Multiplex network body ECU)

      1. *: w/ Auto Lock Function

  1. Customizing with the Multi-display (w/ Navigation System (for Radio and Display Type))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Speed sensitive auto locking*
      On
      Function that locks all doors when the vehicle speed reaches a certain level.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto ;ock by shift from P*
      Off
      Function that locks all doors when the shift lever is moved out of P with the ignition switch ON and all doors closed.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto unlock by shift to P*
      Off
      Function that unlock all doors when the shift lever is moved to P from any position other than P with the ignition switch ON.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto unlock by driver door*
      Off
      Function that unlocks the other doors when the driver door is opened within 10 seconds after the ignition switch is turned off.
      On or Off
      Main body ECU (Multiplex network body ECU)

      1. *: w/ Auto Lock Function

  1. Customizing with the Multi-display (w/ Audio and Visual System (for Radio and Display Type))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: MENU or APPS / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Speed sensitive auto locking*
      On
      Function that locks all doors when the vehicle speed reaches a certain level.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto ;ock by shift from P*
      Off
      Function that locks all doors when the shift lever is moved out of P with the ignition switch ON and all doors closed.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto unlock by shift to P*
      Off
      Function that unlock all doors when the shift lever is moved to P from any position other than P with the ignition switch ON.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Auto unlock by driver door*
      Off
      Function that unlocks the other doors when the driver door is opened within 10 seconds after the ignition switch is turned off.
      On or Off
      Main body ECU (Multiplex network body ECU)

      1. *: w/ Auto Lock Function



4. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Utility / Customize / Wireless Door Lock.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Wireless Control
      ON
      Function that turns wireless door lock on or off
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Hazard Answer Back
      ON
      Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Open Door Warning
      ON
      The buzzer sounds when lock is pressed when any of the doors are ajar.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Unlock 2 Operation
      OFF
      Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Panic Function*2
      ON
      Function to operate theft deterrent system by continuously pressing panic switch on electrical key transmitter sub-assembly for 0.8 seconds
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Trunk Lid Operation
      Long1
      Function to change the operation method of opening the luggage compartment door by the electrical key transmitter sub-assembly.
      1tim ON: Push the luggage open switch once
      2tim ON: Push the luggage open switch twice
      Long1: Push the luggage open switch for 0.8 seconds
      Long2: Push the luggage open switch for 1.6 seconds
      Prohibit: Wireless luggage compartment door open function is off
      1tim ON, 2tim ON, Long1, Long2 or Prohibit
      Main body ECU (Multiplex network body ECU)
      Auto Lock Time
      30 s
      Function that regulates the interval between unlocking and automatic relocking of doors
      30 s, 60 s or 120 s
      Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Resp*1
      ON
      Wireless door lock buzzer response
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      P/W Wireless Ope Buzz
      ON
      Wireless power window buzzer response
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Vol*1
      Level 5
      Wireless door lock buzzer volume
      Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0
      Main body ECU (Multiplex network body ECU)

      1. *1: w/ Wireless Door Lock Buzzer Answer Back Function
      2. *2: for TMMK Made

  1. Customizing with the multi-display (w/ Navigation System (for Radio and Display Type))

    1. Turn the engine switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Remote 2-press unlock
      Off
      Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is Off, pressing unlock switch once makes all doors unlock.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock/unlock feedback lights
      On
      Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock feedback volume*
      5
      Wireless door lock buzzer volume
      Off, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)

      1. *: w/ Wireless Door Lock Buzzer Answer Back Function

  1. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type))

    1. Turn the engine switch on (IG).

    2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Remote 2-press unlock
      Off
      Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is Off, pressing unlock switch once makes all doors unlock.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock/unlock feedback lights
      On
      Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock feedback volume*
      5
      Wireless door lock buzzer volume
      Off, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)

      1. *: w/ Wireless Door Lock Buzzer Answer Back Function

  1. Customizing with the multi-display (w/ Audio and Visual System)

    1. Turn the engine switch on (IG).

    2. Enter the following menus: MENU or APPS / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Remote 2-press unlock
      Off
      Function that unlocks driver door when unlock switch on electrical key transmitter sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is Off, pressing unlock switch once makes all doors unlock.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock feedback volume*
      5
      Wireless door lock buzzer volume
      Off, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)

      1. *: w/ Wireless Door Lock Buzzer Answer Back Function



5. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Entry and Start System)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Utility / Customize / Wireless Door Lock.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Wireless Control
      ON
      Function that turns wireless door lock on or off
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Hazard Answer Back
      ON
      Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Open Door Warning
      ON
      The buzzer sounds when lock is pressed when any of the doors are ajar.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Unlock 2 Operation
      OFF
      Function that unlocks driver door when unlock switch on door control transmitter module set sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is OFF, pressing unlock switch once makes all doors unlock.
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Trunk Lid Operation
      Long1
      Function to change the operation method of opening the luggage compartment door by the door control transmitter module set sub-assembly.
      1tim ON: Push the luggage open switch once
      2tim ON: Push the luggage open switch twice
      Long1: Push the luggage open switch for 0.8 seconds
      Long2: Push the luggage open switch for 1.6 seconds
      Prohibit: Wireless luggage compartment door open function is off
      1tim ON, 2tim ON, Long1, Long2 or Prohibit
      Main body ECU (Multiplex network body ECU)
      Auto Lock Time
      30 s
      Function that regulates the interval between unlocking and automatic relocking of doors
      30 s, 60 s or 120 s
      Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Resp*
      ON
      Wireless door lock buzzer response/on or off
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      P/W Wireless Ope buzzer
      ON
      Wireless power window buzzer response/on or off
      OFF or ON
      Main body ECU (Multiplex network body ECU)
      Wireless Buzzer Vol*
      Level 5
      Wireless door lock buzzer volume
      Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0
      Main body ECU (Multiplex network body ECU)

      1. *: w/ Wireless Door Lock Buzzer Answer Back Function

  1. Customizing with the multi-display (w/ Navigation System (for Radio and Display Type))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Remote 2-press unlock
      Off
      Function that unlocks driver door when unlock switch on door control transmitter module set sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is Off, pressing unlock switch once makes all doors unlock.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock/unlock feedback lights
      On
      Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock feedback volume*
      5
      Wireless door lock buzzer volume
      Off, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)

      1. *: w/ Wireless Door Lock Buzzer Answer Back Function

  1. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type))

    1. Turn the ignition switch to ON.

    2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Remote 2-press unlock
      Off
      Function that unlocks driver door when unlock switch on door control transmitter module set sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is Off, pressing unlock switch once makes all doors unlock.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock/unlock feedback lights
      On
      Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock feedback volume*
      5
      Wireless door lock buzzer volume
      Off, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)

      1. *: w/ Wireless Door Lock Buzzer Answer Back Function

  1. Customizing with the multi-display (w/ Audio and Visual System)

    1. Turn the ignition switch to ON.

    2. Enter the following menus: MENU or APPS / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Remote 2-press unlock
      Off
      Function that unlocks driver door when unlock switch on door control transmitter module set sub-assembly is pressed once, and unlocks all doors when pressed twice. If setting is Off, pressing unlock switch once makes all doors unlock.
      On or Off
      Main body ECU (Multiplex network body ECU)
      Lock feedback volume*
      5
      Wireless door lock buzzer volume
      Off, 1, 2, 3, 4, 5, 6 or 7
      Main body ECU (Multiplex network body ECU)

      1. *: w/ Wireless Door Lock Buzzer Answer Back Function



6. CUSTOMIZE SMART ENTRY AND START SYSTEM (for Entry Function)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body or Entry & Start / Utility / Customize / Wireless Door Lock, Entry & Start or Warning.

    5. Select the setting by referring to the table below.

      Wireless Door Lock 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Hazard Answer Back
      ON
      When the doors are locked by entry function, the hazard warning lights flash once.
      When the doors are unlocked by entry function, the hazard warning lights flash twice.
      OFF or ON
      Main body ECU (multiplex network body ECU)
      Open Door Warning
      ON
      The buzzer sounds when the lock sensor on the door outside handle assembly is touched to perform entry lock with a door open.
      OFF or ON
      Main body ECU (multiplex network body ECU)
      Auto Lock Time
      30 s
      Function that regulates the interval between unlocking and automatic relocking of doors.
      30 s, 60 s or 120 s
      Main body ECU (multiplex network body ECU)
      Wireless Buzzer Resp*
      ON
      Function that sounds the answer-back buzzer when an entry lock or unlock operation is performed.
      OFF or ON
      Main body ECU (multiplex network body ECU)
      Wireless Buzzer Vol*
      Level 5
      Buzzer answer back volume
      Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level0
      Main body ECU (multiplex network body ECU)

      1. *: w/ Wireless Door Lock Buzzer Answer Back Function

      Entry & Start 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Park Wait Time (Waiting time to permit unlocking door after locking)
      2.5s
      Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed.
      0.5s, 1.5s, 2.5s or 5s
      Certification ECU (smart key ECU assembly)
      Ignition Available Area
      (Entry ignition available area)
      All
      Function that sets the area that the key must be in before the engine switch can be operated.
      Front or All
      Certification ECU (smart key ECU assembly)
      Trunk Open Mode
      ON
      Function that opens the luggage compartment door when the driver has the electrical key transmitter sub-assembly and presses the luggage door opening switch assembly.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Door Unlock Mode2*
      All
      Function that chooses the doors to be operated by entry unlock operation.
      All or Driver
      Certification ECU (smart key ECU assembly)
      Auto Entry Cancel SW
      OFF
      Function that enables or disables the smart entry and start system.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Touch Activation Over Threshold
      Active
      The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed.
      Active or Not Active
      Certification ECU (smart key ECU assembly)
      Engine Start Indicator
      ON
      Function that turns the smart warning light on the combination meter assembly on or off.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      1. *: w/ Driver Door Entry Function

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Key Low Battery Warning (Warn when key battery becomes weak)
      ON
      Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more.
      OFF or ON
      Certification ECU (smart key ECU assembly)

  1. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type))

    1. Turn the engine switch on (IG).

    2. Enter the following menus: MENU /Setup / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Select doors to unlock
      All Doors
      Function that sets which doors are unlocked by the entry unlock function.
      All Doors or Driver's Door
      Certification ECU (smart key ECU assembly)
      Entry and start system
      On
      Function that enables or disables the smart entry and start system.
      On or Off
      Certification ECU (smart key ECU assembly)

  1. Customizing with the multi-display (w/ Navigation System (for Radio and Display Type))

    1. Turn the engine switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Select doors to unlock
      All Doors
      Function that sets which doors are unlocked by the entry unlock function.
      All Doors or Driver's Door
      Certification ECU (smart key ECU assembly)
      Entry and start system
      On
      Function that enables or disables the smart entry and start system.
      On or Off
      Certification ECU (smart key ECU assembly)

  1. Customizing with the multi-display (w/ Audio and Visual System)

    1. Turn the engine switch on (IG).

    2. Enter the following menus: MENU or APPS / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Select doors to unlock
      All Doors
      Function that sets which doors are unlocked by the entry unlock function.
      All Doors or Driver's Door
      Certification ECU (smart key ECU assembly)
      Entry and start system
      On
      Function that enables or disables the smart entry and start system.
      On or Off
      Certification ECU (smart key ECU assembly)



  1. Entry unlock mode switching function (manual operation) (w/ Driver Door Entry Function)

    1. The following entry unlock modes can be selected when using the entry unlock mode switching function.

      1. All door unlock mode: When the sensor of a front door outside handle assembly is touched, an entry unlock operation is performed simultaneously for all doors.
      2. Driver door unlock mode: When the sensor of the driver side door outside handle assembly is touched, an entry unlock operation is performed for the driver door only. If any other door handle is touched, an entry unlock operation is performed simultaneously for all doors.



    2. When customizing through manual operation:

      1. Turn the engine switch off.
      2. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock buttons of the electrical key transmitter sub-assembly for 5 seconds or more while the electrical key transmitter sub-assembly is in the actuation area.
      3. Check the current setting.

        HINT:
        1. The mode changes from all door unlock mode to driver door unlock mode and then back to all door unlock mode.
        2. The answer-back (wireless buzzer, buzzer in the combination meter assembly) operation for each mode is indicated in the table below.

          Currently Selected Mode
          Answer-back (Wireless Buzzer)
          Answer-back (Buzzer in Combination Meter Assembly)
          All door unlock mode
          Buzzer sounds twice (short beeps)
          Buzzer sounds once
          Driver door unlock mode
          Buzzer sounds 3 times (short beeps)
          Buzzer sounds once

      4. Release the lock and unlock buttons of the electrical key transmitter sub-assembly.
      5. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock buttons of the electrical key transmitter sub-assembly for 5 seconds or more to change the mode.

        HINT:
        Repeat the procedure as necessary to select the desired mode.

      6. Unlock the doors with the wireless operation, and then open any door


      B358054E02

  1. Entry cancel function (manual operation)

    HINT:
    While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.


    1. The following functions are disabled when the smart entry and start system is canceled.

      1. Entry unlock/lock functions
      2. Entry luggage compartment door open function
      3. Push start function
      4. Key lock-in prevention function
      5. Entry warning functions

    2. When canceling the system through manual operation:

      1. Make sure the following conditions are met:
        1. The engine switch is off.
        2. The driver door is closed.
        3. The driver door is unlocked.
      2. Press the unlock button of the electrical key transmitter sub-assembly.
      3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).
      4. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      5. Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).
      6. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      7. Close and open the driver door completing the step above (driver door: open condition → closed → opened).
      8. Close the driver door within 5 seconds of completing the above step.
      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart entry and start system has been canceled.

      HINT:
      Finish the step 5 to 7 within 30 seconds.

    3. Perform the following procedure to restore the smart entry and start system to the active state from the canceled state.

      1. Perform the procedures to cancel the smart entry and start system again.
      2. Check that the wireless buzzer sounds once (short beep) to confirm that the smart entry and start system has been restored to the active state.

        HINT:
        1. The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.
        2. The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.



7. CUSTOMIZE SMART ENTRY AND START SYSTEM (for Start Function)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry & Start / Utility / Customize / Entry & Start or Warning

    5. Select the setting by referring to the table below.

      Entry & Start 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Ignition Available Area
      (Entry ignition available area)
      All
      Function that sets the area that the key must be in before the engine switch can be operated.
      Front or All
      Certification ECU (smart key ECU assembly)
      Auto Entry Cancel SW
      OFF
      Function that enables or disables the smart entry and start system.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Engine Start Indicator
      ON
      Function that turns the smart warning light on the combination meter assembly on or off.
      OFF or ON
      Certification ECU (smart key ECU assembly)

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Key Low Battery Warning (Warn when key battery becomes weak)
      ON
      Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more.
      ON or OFF
      Certification ECU (smart key ECU assembly)

  1. Customizing with the multi-display (w/ Navigation System (for Navigation Receiver Type))

    1. Turn the engine switch on (IG).

    2. Enter the following menus: MENU /Setup / Vehicle / Vehicle customization / Door lock setting.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Entry and start system
      On
      Function that enables or disables the smart entry and start system.
      On or Off
      Certification ECU (smart key ECU assembly)

  1. Customizing with the multi-display (w/ Navigation System (for Radio and Display Type))

    1. Turn the engine switch on (IG).

    2. Enter the following menus: SETUP / Vehicle / Vehicle customization / Door lock setting.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Entry and start system
      On
      Function that enables or disables the smart entry and start system.
      On or Off
      Certification ECU (smart key ECU assembly)

  1. Customizing with the multi-display (w/ Audio and Visual System)

    1. Turn the engine switch on (IG).

    2. Enter the following menus: MENU or APPS / Vehicle / Vehicle customization / Door lock setting.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Entry and start system
      On
      Function that enables or disables the smart entry and start system.
      On or Off
      Certification ECU (smart key ECU assembly)

  1. Entry cancel function (manual operation)

    HINT:
    While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.


    1. The following functions are disabled when the smart entry and start system is canceled.

      1. Entry unlock/lock functions
      2. Entry luggage compartment door open function
      3. Push-button start function
      4. Key lock-in prevention function
      5. Entry warning functions

    2. When canceling the system through manual operation:

      1. Make sure the following conditions are met:
        1. The engine switch is off.
        2. The driver door is closed.
        3. The driver door is unlocked.
      2. Press the unlock button of the electrical key transmitter sub-assembly.
      3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).
      4. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      5. Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).
      6. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      7. Close and open the driver door completing the step above (driver door: open condition → closed → opened).
      8. Close the driver door within 5 seconds of completing the above step.
      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart entry and start system has been canceled.

      HINT:
      Finish the step 5 to 7 within 30 seconds.

    3. Perform the following procedure to restore the smart entry and start system to the active state from the canceled state.

      1. Perform the procedures to cancel the smart entry and start system again.
      2. Check that the wireless buzzer sounds once (short beep) to confirm that the smart entry and start system has been restored to the active state.

        HINT:
        1. The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.
        2. The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.



8. CUSTOMIZE PUSH-BUTTON START

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry & Start / Utility / Customize / Entry & Start or Warning

    5. Select the setting by referring to the table below.

      Entry & Start 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Ignition Available Area
      (Entry ignition available area)
      All
      Function that sets the area that the key must be in before the engine switch can be operated.
      Front or All
      Certification ECU (smart key ECU assembly)
      Auto Entry Cancel SW
      OFF
      Function that enables or disables the smart entry and start system.
      OFF or ON
      Certification ECU (smart key ECU assembly)
      Engine Start Indicator
      ON
      Function that turns the smart warning light on the combination meter assembly on or off.
      OFF or ON
      Certification ECU (smart key ECU assembly)

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Key Low Battery Warning (Warn when key battery becomes weak)
      ON
      Enables or disables the sounding of the buzzer when the transmitter battery is low and the engine switch is turned off after being on (IG) for 20 minutes or more.
      ON or OFF
      Certification ECU (smart key ECU assembly)

  1. Customizing with the multi-display (w/ Audio and Visual System)

    1. Turn the engine switch on (IG).

    2. Enter the following menus: MENU or APPS / Vehicle / Vehicle customization / Door lock settings.

    3. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Entry and start system
      On
      Function that enables or disables the smart entry and start system.
      On or Off
      Certification ECU (smart key ECU assembly)

  1. Entry cancel function (manual operation)

    HINT:
    While the push-button start is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.


    1. The following functions are disabled when the push-button start is canceled.

      1. Entry unlock/lock functions
      2. Entry luggage compartment door open function
      3. Push-button start function
      4. Key lock-in prevention function
      5. Entry warning functions

    2. When canceling the system through manual operation:

      1. Make sure the following conditions are met:
        1. The engine switch is off.
        2. The driver door is closed.
        3. The driver door is unlocked.
      2. Press the unlock button of the electrical key transmitter sub-assembly.
      3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).
      4. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      5. Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).
      6. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times completing the step above.

        NOTICE:
        If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

      7. Close and open the driver door completing the step above (driver door: open condition → closed → opened).
      8. Close the driver door within 5 seconds of completing the above step.
      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the push-button start has been canceled.

      HINT:
      Finish the step 5 to 7 within 30 seconds.

    3. Perform the following procedure to restore the push-button start to the active state from the canceled state.

      1. Perform the procedures to cancel the push-button start again.
      2. Check that the wireless buzzer sounds once (short beep) to confirm that the push-button start has been restored to the active state.

        HINT:
        1. The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.
        2. The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.



9. CUSTOMIZE THEFT DETERRENT SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Utility / Customize / Security.

    5. Select the setting by referring to the table below.

      Security 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Security control with mechanism key*
      OFF
      This function makes it possible to cancel the security alarm with the mechanical key.
      ON or OFF
      Main Body ECU (Multiplex Network Body ECU)

      1. *: w/o Wireless Door Lock Buzzer Answer Back Function and w/ Smart Entry and Start System

    6. Enter the following menus: Body / Main Body / Utility / Customize / Wireless Door Lock.

    7. Select the setting by referring to the table below.

      Wireless Door Lock 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Panic Function*
      ON
      This function operates the theft deterrent system when the panic switch is pressed and held for 0.8 seconds.
      ON or OFF
      Main Body ECU (Multiplex Network Body ECU)

      1. *: w/ Panic Switch



10. CUSTOMIZE LIGHTING SYSTEM (INT)
  1. Customizing using the intelligent tester

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.

    HINT:
    The following items can be customized.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Utility / Customize / Illuminated Entry.

    5. Select the setting by referring to the table below.

      Illuminated Entry (for TMC, TMMR Made) 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Lighting Time
      15 s
      Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the ignition switch from off to ON or ACC.)
      7.5 s, 15 s or 30 s
      Main body ECU (Multiplex network body ECU)
      I/L when ACC OFF
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2, personal light, rear interior light, inside handle illumination lights and footwell lights when the ignition switch is turned from ON or ACC to off.
      ON or OFF
      I/L ON W/Door Key Unlock
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2, personal light, rear interior light, inside handle illumination lights and footwell lights when doors are unlocked using a mechanical key or door control transmitter.
      ON or OFF
      Light Control
      ON
      Dims (ON setting) or turns off (OFF setting) the inside handle illumination lights and footwell lights when all of the following conditions are met:
      1. Ignition switch ON
      2. The shift lever is moved out of P.
      3. All doors are closed.
      ON or OFF
      Room Light when Aprchd
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2, personal light and rear interior light when a key enters any actuation area around the doors.
      ON or OFF
      Inside Foot Light
      ON
      Lights up the inside handle illumination lights and footwell lights illumination.
      ON or OFF
      Interior Light Control
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2, personal light, rear interior light, inside handle illumination lights and footwell lights when the illuminated entry function is operating.
      ON or OFF

      1. *1: w/ Smart Entry and Start System
      2. *2: w/o Smart Entry and Start System

      Illuminated Entry (for TMMK Made) 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Lighting Time
      15 s
      Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the ignition switch from off to ON or ACC.)
      7.5 s, 15 s or 30 s
      Main body ECU (Multiplex network body ECU)
      I/L when ACC OFF
      ON
      Lights up the engine switch illumination, personal light* and rear interior light when the ignition switch is turned from ON or ACC to off.
      ON or OFF
      I/L ON W/Door Key Unlock
      ON
      Lights up the engine switch illumination, personal light* and rear interior light when doors are unlocked using a mechanical key or door control transmitter.
      ON or OFF
      Room Light when Aprchd
      ON
      Lights up the engine switch illumination, personal light* and rear interior light when a key enters any actuation area around the doors.
      ON or OFF
      Interior Light Control
      ON
      Lights up the engine switch illumination, personal light* and rear interior light when the illuminated entry function is operating.
      ON or OFF
      1. *: w/ Sliding Roof

  1. Customizing using the multi-display (w/ Navigation System)

    1. Turn the ignition switch to ON.

    2. Enter the following menus: Setup / Vehicle / Vehicle Customization / Light Settings

    3. Select the setting by referring to the table below:

      Light Settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Interior Lights Off Timer
      15 sec.
      Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the ignition switch from off to ACC or ON.)
      Off, 7.5 sec., 15 sec., or 30 sec.
      Main body ECU (Multiplex network body ECU)



11. CUSTOMIZE METER / GAUGE SYSTEM
  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Warning.

    5. Select the setting by referring to the table below.

      NOTICE:
      1. Record the current settings before customizing.


      Warning 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Key Remind Sound
      Slow
      Function to change the frequency of the key reminder warning buzzer
      Fast, Normal, Slow
      Combination meter assembly
      Flasher Sound Volume Adjustment*1
      Medium
      Function to change to flasher sound volume
      Large, Medium, Small
      Combination meter assembly
      Lane Change Flashing Times Setting
      3
      Function to change the lane change flashing time
      OFF, 3, 4, 5, 6, 7
      Combination meter assembly

      Display 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      ODO Display Time After IG OFF Setting*2
      30s
      Function to change the odometer display time after the ignition switch is turned off
      OFF, 30s, 60s, 600s
      Combination meter assembly
      1. *1: except TMMK Made
      2. *2: for TMMK Made



12. CUSTOMIZE SEAT BELT WARNING SYSTEM (w/ Occupant Classification System)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.
  4. These buzzers should be ON for safe driving. Perform this procedure only if it is necessary to set the buzzer to OFF (disabled).

  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Warning.

    5. Select the setting by referring to the table below.

      Warning 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Driver Side Seatbelt Warning Buzzer
      ON
      Function to sound the driver seat belt warning buzzer
      ON/OFF
      Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer
      ON
      Function to sound the front passenger seat belt warning buzzer
      ON/OFF

      HINT:
      This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.



13. CUSTOMIZE SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.
  4. These buzzers should be ON for safe driving. Perform this procedure only if it is necessary to set the buzzer to OFF (disabled).

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Combination Meter / Utility / Customize / Warning.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Driver Side Seatbelt Warning Buzzer
      ON
      Function to sound the driver seat belt warning buzzer
      ON/OFF
      Combination meter assembly

      HINT:
      This setting is only valid when the vehicle is driven at 20 km/h (12 mph) or more.



14. CUSTOMIZE AIR CONDITIONING SYSTEM
  1. Customizing with the intelligent tester.

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.

    HINT:
    The following items can be customized.


    1. Connect the intelligent tester.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Air Conditioner / Utility / Customize.

    5. Select the setting by referring to the table below.

      Air Conditioner 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Set Temperature Shift
      Normal
      Function to perform control with the shifted temperature versus the displayed temperature
      -2C, -1C, Normal, +1C, +2C
      Air Conditioning Amplifier Assembly
      Evaporator Control
      Automatic
      Function to set the evaporator control to the AUTOMATIC position (AUTO) to save power or to the coldest position (MANUAL) to dehumidify the air and to prevent the windows from fogging up
      Automatic or Manual
      Air Conditioning Amplifier Assembly
      Compressor Mode
      Automatic
      Function to turn the air conditioning on automatically by pressing the AUTO button when the blower is on and the air conditioning is off
      Automatic or Manual
      Air Conditioning Amplifier Assembly
      Air Inlet Mode
      Automatic
      Function to change the mode automatically to recirculation air mode when turning the air conditioning on to cool the cabin quickly
      Automatic or Manual
      Air Conditioning Amplifier Assembly
      Foot/DEF Auto Mode
      ON
      Function to turn the airflow from FOOT/DEF ON automatically when AUTO MODE is ON
      ON or OFF
      Air Conditioning Amplifier Assembly
      Foot/DEF Automatic Blow Up Function
      ON
      Function to increase the blower level automatically when the defroster is ON
      ON or OFF
      Air Conditioning Amplifier Assembly
      Ambient Temperature Shift
      Normal
      Function to display shifted ambient temperature versus actual ambient temperature
      -3C, -2C, -1C, Normal, +1C, +2C, +3C
      Air Conditioning Amplifier Assembly
      Refrigerant Shortage Check
      ON
      Function to cancel the refrigerant shortage check (check performed during normal operation) when item is OFF
      ON or OFF
      Air Conditioning Amplifier Assembly
      Fan speed increment control
      Normal
      Function to define how fast the AC blower goes to target speed when first activating the AC
      Slow, Normal, Fast
      Air Conditioning Amplifier Assembly
      Ion Generate Control*
      ON
      Function to generate ions is stopped when item is OFF
      ON or OFF
      Air Conditioning Amplifier Assembly

      1. *: w/ Ion Generator Sub-assembly

  1. Customizing with the multi-display. (for TMC, TMMR Made)

    1. Turn the ignition switch to ON.

    2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Climate settings. (w/ Navigation System (for Navigation Receiver Type))

    3. Enter the following menus: SETUP / Vehicle / Vehicle customization / Climate settings. (w/ Navigation System (for Radio and Display Type))

    4. Enter the following menus: MENU or APPS / Vehicle / Vehicle customization / Climate settings. (w/ Audio and Visual System)

    5. Select the setting by referring to the table below.

      Climate settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Auto A/C mode
      On
      Function to turn the air conditioning on automatically by pressing the AUTO button when the blower is on and the air conditioning is off
      On or Off
      Air Conditioning Amplifier Assembly
      Efficient ventilation mode
      On
      Function to change the mode automatically to recirculation air mode when turning the air conditioning on to cool the cabin quickly
      On or Off
      Air Conditioning Amplifier Assembly

  1. Customizing with the multi-display. (for TMMK Made)

    1. Turn the ignition switch to ON.

    2. Enter the following menus: APPS / Setup / Vehicle / Vehicle customization / Climate settings. (w/ Navigation System)

    3. Select the setting by referring to the table below.

      Climate settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Auto A/C mode
      On
      Function to turn the air conditioning on automatically by pressing the AUTO button when the blower is on and the air conditioning is off
      On or Off
      Air Conditioning Amplifier Assembly
      Efficient ventilation mode
      On
      Function to change the mode automatically to recirculation air mode when turning the air conditioning on to cool the cabin quickly
      On or Off
      Air Conditioning Amplifier Assembly



15. CUSTOMIZE REAR SUNSHADE SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Record the current settings before customizing.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Utility / Customize / Others.

    5. Select the setting by referring to the table below.

      Others 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Rear Shade Delay Time
      0.7 s
      Function to change the time lag of the shift-linked operation
      0.7 s, 1.2 s, 0.9 s or 0.0 s
      Main body ECU (Multiplex network body ECU)
      R-pos to Rear Sun Shade COM
      ON
      Function to lower the rear sunshade when the shift lever is moved to R with the rear sunshade raised
      ON / OFF
      Main body ECU (Multiplex network body ECU)



16. CUSTOMIZE POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows)

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function(s) can be customized.
  2. Be sure to make notes of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Utility / Customize / Power Window.

    5. Select the setting by referring to the table below.

      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Door Key P/W Up
      OFF
      This function is used to close the windows by operating the mechanical key.
      OFF/ON
      Main body ECU (Multiplex network body ECU)
      Door Key P/W Down
      OFF
      This function is used to open the windows by operating the mechanical key.
      OFF/ON
      Main body ECU (Multiplex network body ECU)
      P/W Up W/ Transmit
      OFF
      This function is used to close the windows using the wireless key transmitter.
      OFF/ON
      Main body ECU (Multiplex network body ECU)
      P/W Down W/ Transmit
      OFF
      This function is used to open the windows using the wireless key transmitter.
      OFF/ON
      Main body ECU (Multiplex network body ECU)
      P Window Auto Up
      Avail
      This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly (for front passenger door).
      Not Avl/Avail
      Power window ECU (Power window regulator motor assembly)
      P Window Auto Up From Driver
      Avail
      This function is used to enable or disable the remote auto up function for the front passenger door window using the multiplex network master switch assembly.
      Not Avl/Avail
      Power window ECU (Power window regulator motor assembly)
      RR Window Auto Up
      Avail
      This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear RH door).
      Not Avl/Avail
      Power window ECU (Power window regulator motor assembly)
      RR Window Auto Up From Driver
      Avail
      This function is used to enable or disable the remote auto up function for the rear RH door window using the multiplex network master switch assembly.
      Not Avl/Avail
      Power window ECU (Power window regulator motor assembly)
      RL Window Auto Up
      Avail
      This function is used to enable or disable the auto up function using the power window regulator switch assembly (for rear LH door).
      Not Avl/Avail
      Power window ECU (Power window regulator motor assembly)
      RL Window Auto Up From Driver
      Avail
      This function is used to enable or disable the remote auto up function for the rear LH door window using the multiplex network master switch assembly.
      Not Avl/Avail
      Power window ECU (Power window regulator motor assembly)

    6. Enter the following menus: Body / Main Body / Utility / Customize / Wireless Door Lock.

    7. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      P/W Wireless Ope Buzz
      ON
      This function turns the wireless power window buzzer response on or off.
      OFF/ON
      Main body ECU (Multiplex network body ECU)



17. CUSTOMIZE POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows)

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make notes of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

HINT:
The following items can be customized.

  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Power Window.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      D Window Auto Up
      ON
      This function is used to enable or disable the auto up function for the driver door window using the power window regulator master switch assembly.
      OFF/ON
      Power window regulator motor assembly (for driver door)
      D Window Auto Down
      ON
      This function is used to enable or disable the auto down function for the driver door window using the power window regulator master switch assembly.
      OFF/ON
      Power window regulator motor assembly (for driver door)
      P Window Auto Up
      ON
      This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly.
      OFF/ON
      Power window regulator motor assembly (for front passenger door)
      P Window Auto Up From Driver
      ON
      This function is used to enable or disable the remote auto up function for the front passenger door window using the power window regulator master switch assembly.
      OFF/ON
      Power window regulator motor assembly (for front passenger door)
      P Window Auto Down
      ON
      This function is used to enable or disable the auto down function for the front passenger door window using the power window regulator switch assembly.
      OFF/ON
      Power window regulator motor assembly (for front passenger door)
      P Window Auto Down From Driver
      ON
      This function is used to enable or disable the remote auto down function for the front passenger door window using the power window regulator master switch assembly.
      OFF/ON
      Power window regulator motor assembly (for front passenger door)



18. CUSTOMIZE SLIDING ROOF SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function(s) can be customized.
  2. Be sure to make notes of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Utility / Customize / Power Window.

    5. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Door Key P/W Up*
      OFF
      This function is used to close the power windows and sliding roof by operating the mechanical key.
      OFF/ON
      Main body ECU (Multiplex network body ECU)
      Door Key P/W Down*
      OFF
      This function is used to open the power windows and sliding roof by operating the mechanical key.
      OFF/ON
      Main body ECU (Multiplex network body ECU)
      P/W Up W/ Transmit*
      OFF
      This function is used to close the power windows and sliding roof using the wireless key transmitter.
      OFF/ON
      Main body ECU (Multiplex network body ECU)
      P/W Down W/ Transmit*
      OFF
      This function is used to open the power windows and sliding roof using the wireless key transmitter.
      OFF/ON
      Main body ECU (Multiplex network body ECU)

      1. *: except TMMK Made

    6. Enter the following menus: Body / Sliding Roof / Utility / Customize / Slide Roof.

    7. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Door Key Related Operation*
      Slide
      Function to select tilt up or slide open of sliding roof key-linked function.
      Slide/Tilt
      Sliding roof ECU (Sliding roof drive gear sub-assembly)
      Wireless Key Related Operation*
      Slide
      Function to select tilt up or slide open of sliding roof wireless transmitter-linked function.
      Slide/Tilt
      Sliding roof ECU (Sliding roof drive gear sub-assembly)
      Front SW Auto Operation
      ON
      This function is used to enable or disable the auto operation.
      OFF/ON
      Sliding roof ECU (Sliding roof drive gear sub-assembly)

      1. *: except TMMK Made

    8. Enter the following menus: Body / Main Body / Utility / Customize / Security.

    9. Select the setting by referring to the table below.

      Display
      Default
      Content
      Setting
      Relevant ECU
      Slide Roof Open Warning
      ON
      This function is used to enable or disable the sliding roof open warning.
      OFF/ON
      Main body ECU (Multiplex network body ECU)



19. CUSTOMIZE LIGHTING SYSTEM (EXT)

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

HINT:
The following items can be customized.

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Utility / Customize / Light Control.

    5. Select the setting by referring to the table below.

      Light Control 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Disp Ex ON Sen
      Normal
      Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*A
      Light2, Light1, Normal, Dark1 or Dark2
      Main Body ECU (Multiplex Network Body ECU)
      Disp Ex OFF Sen
      Normal
      Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.*B
      Light2, Light1, Normal, Dark1 or Dark2
      Response Time
      Normal
      Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position
      Normal or Long
      Sensitivity
      Normal
      Adjusts the sensitivity of the automatic light control system.*C
      Light2, Light1, Normal, Dark1 or Dark2
      DRL Function*
      ON
      ON/OFF of the DRL function
      ON or OFF

      1. *: for TMMK Made

      HINT:
      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


      *A 
      Brightness level required to dim the lights

      E107164

      Setting
      Dark2
      Dark1
      Normal
      Light1
      Light2

      *B 
      Brightness level required to cancel the dimming of the lights

      E107164

      Setting
      Dark2
      Dark1
      Normal
      Light1
      Light2

      *C 
      Sensitivity of the automatic light control system

      E107164

      Setting
      Dark2
      Dark1
      Normal
      Light1
      Light2

  1. Customizing with multi-display

    1. Turn the ignition switch to ON.

    2. Enter the following menus: MENU or APPS / Vehicle / Vehicle customization / Lights settings. (w/ Audio and Visual System)

    3. Enter the following menus: SETUP / Vehicle / Vehicle customization / Lights settings. (w/ Navigation System (for Radio and Display Type)

    4. Enter the following menus: MENU / Vehicle / Vehicle customization / Lights settings. (w/ Navigation System (for Navigation Receiver Type)

    5. Select the setting by referring to the table below.

      Vehicle settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Light sensor sensitivity
      0
      Adjusts the sensitivity of the automatic light control system.*A
      -2, -1, 0, +1 or +2
      Main Body ECU (Multiplex Network Body ECU)
      Daytime running lights*
      On
      ON/OFF of the DRL function
      On or Off

      1. *: for TMMK Made

      HINT:
      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.


      *A 
      Sensitivity of the automatic light control system

      E107164

      Setting
      -2
      -1
      0
      +1
      +2



20. CUSTOMIZE AUTOMATIC HIGH BEAM SYSTEM

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

HINT:
The following item can be customized.

  1. Customizing with the GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Customize Setting / Light Control.

    5. Select the setting by referring to the table below.

      Light Control 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Automatic High Beam
      On
      Enabling (On) or disabling (Off) of the automatic high beam function
      On or Off
      Main Body ECU (Multiplex Network Body ECU)