Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > CUSTOMIZE PARAMETERS

for Preparation Click here



1. CUSTOMIZE LIGHTING SYSTEM (INT)
  1. Customizing using the intelligent tester

    NOTICE:
    1. When the customer requests a change in a function, first make sure that the function can be customized.
    2. Be sure to make a note of the current settings before customizing.
    3. When troubleshooting a function, first make sure that the function is set to the default setting.

    HINT:
    The following items can be customized.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Utility / Customize / Illuminated Entry.

    5. Select the setting by referring to the table below.

      Illuminated Entry (for TMC, TMMR Made) 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Lighting Time
      15 s
      Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the ignition switch from off to ON or ACC.)
      7.5 s, 15 s or 30 s
      Main body ECU (Multiplex network body ECU)
      I/L when ACC OFF
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2, personal light, rear interior light, inside handle illumination lights and footwell lights when the ignition switch is turned from ON or ACC to off.
      ON or OFF
      I/L ON W/Door Key Unlock
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2, personal light, rear interior light, inside handle illumination lights and footwell lights when doors are unlocked using a mechanical key or door control transmitter.
      ON or OFF
      Light Control
      ON
      Dims (ON setting) or turns off (OFF setting) the inside handle illumination lights and footwell lights when all of the following conditions are met:
      1. Ignition switch ON
      2. The shift lever is moved out of P.
      3. All doors are closed.
      ON or OFF
      Room Light when Aprchd
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2, personal light and rear interior light when a key enters any actuation area around the doors.
      ON or OFF
      Inside Foot Light
      ON
      Lights up the inside handle illumination lights and footwell lights illumination.
      ON or OFF
      Interior Light Control
      ON
      Lights up the engine switch illumination*1, ignition key cylinder light*2, personal light, rear interior light, inside handle illumination lights and footwell lights when the illuminated entry function is operating.
      ON or OFF

      1. *1: w/ Smart Entry and Start System
      2. *2: w/o Smart Entry and Start System

      Illuminated Entry (for TMMK Made) 
      Tester Display
      Default
      Content
      Setting
      Relevant ECU
      Lighting Time
      15 s
      Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the ignition switch from off to ON or ACC.)
      7.5 s, 15 s or 30 s
      Main body ECU (Multiplex network body ECU)
      I/L when ACC OFF
      ON
      Lights up the engine switch illumination, personal light* and rear interior light when the ignition switch is turned from ON or ACC to off.
      ON or OFF
      I/L ON W/Door Key Unlock
      ON
      Lights up the engine switch illumination, personal light* and rear interior light when doors are unlocked using a mechanical key or door control transmitter.
      ON or OFF
      Room Light when Aprchd
      ON
      Lights up the engine switch illumination, personal light* and rear interior light when a key enters any actuation area around the doors.
      ON or OFF
      Interior Light Control
      ON
      Lights up the engine switch illumination, personal light* and rear interior light when the illuminated entry function is operating.
      ON or OFF
      1. *: w/ Sliding Roof

  1. Customizing using the multi-display (w/ Navigation System)

    1. Turn the ignition switch to ON.

    2. Enter the following menus: Setup / Vehicle / Vehicle Customization / Light Settings

    3. Select the setting by referring to the table below:

      Light Settings 
      Display
      Default
      Content
      Setting
      Relevant ECU
      Interior Lights Off Timer
      15 sec.
      Changes the lighting time after closing all of the doors. (It will fade out immediately in case of turning the ignition switch from off to ACC or ON.)
      Off, 7.5 sec., 15 sec., or 30 sec.
      Main body ECU (Multiplex network body ECU)