BLIND SPOT MONITOR SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Main Switch | Blind spot monitor main switch (warning canceling switch assembly) / ON or OFF | ON: Blind spot monitor main switch (warning canceling switch assembly) on OFF: Blind spot monitor main switch (warning canceling switch assembly) off | - |
| Warning Indicator Turning on (Master) | State of the outer rear view mirror indicator RH turning on / OFF or ON | OFF: The following conditions are not met
| - |
| Warning Indicator Flashing (Master) | State of the outer rear view mirror indicator RH flashing / OFF or ON | OFF: The following conditions are not met
| - |
| Main Switch Indicator Status | State of the blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) / OFF or ON | OFF: Indicator not illuminated ON: Indicator illuminated | - |
| Warning Indicator Input Circuit Voltage | Outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V | Indicator illuminated: 2.5 to 7.5 V Indicator not illuminated: Below 1 V | - |
| Warning Indicator Input Circuit Current | Outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA | Indicator illuminated: 5 to 100 mA Indicator not illuminated: 0 mA | - |
| Main Switch Indicator Input Circuit Voltage | Blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) voltage / Min.: 0 V, Max.: 25.5 V | Always: 9 to 16 V | - |
| Turn Switch State | State of the headlight dimmer switch assembly (turn signal light switch) / Left ON, Right ON or OFF | Left ON: Left side of turn signal light switch on Right ON: Right side of turn signal light switch on OFF: Turn signal light switch off | - |
| Reverse (Only for AT/CVT) | State of the shift position R signal / OFF or ON | ON: Shift lever in R OFF: Shift lever in any position except R | - |
| Vehicle Speed | Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor / Min.: -3072°, Max.: 3070.5° | Left turn: Increases Right turn: Decreases | - |
| Power Supply Voltage | Power supply voltage / Min.: 0 V, Max.: 50 V | Always: 11 to 14 V | - |
| Indicator Light Control State | Outer rear view mirror indicator dimming state / Dim OFF or Dim ON | Dim OFF: Indicator not dimmed Dim ON: Indicator dimmed | - |
| HV Flag | Hybrid vehicle / OFF or ON | OFF: Non-hybrid vehicle ON: Hybrid vehicle | - |
| VGRS Flag | VGRS installed / OFF or ON | OFF: VGRS not installed ON: VGRS installed | - |
| Main SW Inspection Completeness Flag | Completion of inspection for blind spot monitor main switch (warning canceling switch assembly) / Incompl or Compl | Incompl: Inspection not completed Compl: Inspection completed | Changes to Compl when the blind spot monitor main switch (warning canceling switch assembly) is changed from off to on during Test Mode. |
| Beam Axis Inspection Completeness Flag | Completion of beam axis inspection / Incompl or Compl | Incompl: Inspection not completed Compl: Inspection completed | Changes to Compl when Test Mode has been entered. |
| Destination Undefined Flag | Destination determination / Unfixed or Fixed | Unfixed: Sensor destination information not determined Fixed: Sensor destination information determined according to CAN destination information | - |
| Angle Adjustment by Auto Alignment | Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg | Angle adjusted using auto alignment is displayed | When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed |
| Setting of Warning Indicator Current (Dim OFF) | Set current of the outer rear view mirror indicator when not dimmed / Min.: 0 mA, Max.: 100 mA | Always: 0 to 100 mA | - |
| Setting of Warning Indicator Current (Dim ON) | Set current of the outer rear view mirror indicator when dimmed / Min.: 0 mA, Max.: 100 mA | Always: 0 to 100 mA | - |
| Mirror LED Duty Ratio (Blinking) | Duty ratio of the outer rear view mirror indicator when blinking / Min.: 0%, Max.: 100% | Always: 50 % | - |
| Main Switch LED Control Frequency | Frequency of the blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) when operating / Min.: 100 Hz, Max.: 500 Hz | Always: 100 Hz | - |
| Main Switch LED Duty Ratio (Bright Condition) | Duty ratio of the blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) when illuminated / Min.: 0 %, Max.: 100 % | Always: 100 % | - |
| Main Switch LED Duty Ratio (Dimmed Condition) | Duty ratio of the blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) when dimmed / Min.: 0 %, Max.: 100 % | Always: 100 % | - |
| Number of DTC | Number of DTC / Min.: 0, Max.: 255 | When system is normal: 0 When a malfunction is detected: More than 0 | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Warning Indicator Turning on (Slave) | State of the outer rear view mirror indicator LH turning on / OFF or ON | OFF: The following conditions are not met
| - |
| Warning Indicator Flashing (Slave) | State of the outer rear view mirror indicator LH flashing / OFF or ON | OFF: The following conditions are not met
| - |
| Buzzer Sound Status | State of the RCTA buzzer (blind spot monitor buzzer) / OFF or ON | OFF: Buzzer not sounding ON: Buzzer sounding | - |
| Warning Indicator Input Circuit Voltage | Outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V | Indicator illuminated: 2.5 to 7.5 V Indicator not illuminated: Below 1 V | - |
| Warning Indicator Input Circuit Current | Outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA | Indicator illuminated: 5 to 100 mA Indicator not illuminated: 0 mA | - |
| Buzzer Input Circuit Voltage | RCTA buzzer (blind spot monitor buzzer) voltage / Min.: 0 V, Max.: 25.5 V | Buzzer not sounding: 11 to 14 V Buzzer sounding: Alternating between 0 to 14 V | - |
| Turn Switch State | State of the headlight dimmer switch assembly (turn signal light switch) / Left ON, Right ON or OFF | Left ON: Left side of turn signal light switch on Right ON: Right side of turn signal light switch on OFF: Turn signal light switch off | - |
| Reverse (Only for AT/CVT) | State of the shift position R signal / OFF or ON | ON: Shift lever in R OFF: Shift lever in any position except R | - |
| Vehicle Speed | Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor / Min.: -3072°, Max.: 3070.5° | Left turn: Increases Right turn: Decreases | - |
| Power Supply Voltage | Power supply voltage / Min.: 0 V, Max.: 50 V | Always: 11 to 14 V | - |
| Indicator Light Control State | Outer rear view mirror indicator dimming state / Dim OFF or Dim ON | Dim OFF: Indicator not dimmed Dim ON: Indicator dimmed | - |
| HV Flag | Hybrid vehicle / OFF or ON | OFF: Non-hybrid vehicle ON: Hybrid vehicle | - |
| VGRS Flag | VGRS installed / OFF or ON | OFF: VGRS not installed ON: VGRS installed | - |
| Beam Axis Inspection Completeness Flag | Completion of beam axis inspection / Incompl or Compl | Incompl: Inspection not completed Compl: Inspection completed | Changes to Compl when Test Mode has been entered. |
| Destination Undefined Flag | Destination determination / Unfixed or Fixed | Unfixed: Sensor destination information not determined Fixed: Sensor destination information determined according to CAN destination information | - |
| Angle Adjustment by Auto Alignment | Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg | Angle adjusted using auto alignment is displayed | When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed |
| Setting of Warning Indicator Current (Dim OFF) | Set current of the outer rear view mirror indicator when not dimmed / Min.: 0 mA, Max.: 100 mA | Always: 0 to 100 mA | - |
| Setting of Warning Indicator Current (Dim ON) | Set current of the outer rear view mirror indicator when dimmed / Min.: 0 mA, Max.: 100 mA | Always: 0 to 100 mA | - |
| Mirror LED Duty Ratio (Blinking) | Duty ratio of the outer rear view mirror indicator when blinking / Min.: 0%, Max.: 100% | Always: 50 % | - |
| Buzzer Control Frequency | Frequency of the RCTA buzzer (blind spot monitor buzzer) when sounding / Min.: 1000 Hz, Max.: 2400 Hz | Always: 2000 Hz | - |
| Number of DTC | Number of DTC / Min.: 0, Max.: 255 | When system is normal: 0 When a malfunction is detected: More than 0 | - |