Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

BLIND SPOT MONITOR SYSTEM > FREEZE FRAME DATA

for Preparation Click here



FREEZE FRAME DATA
  1. Whenever a DTC is detected, the blind spot monitor sensor stores the current vehicle (sensor) state as Freeze Frame Data.


CHECK FREEZE FRAME DATA
  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the blind spot monitor main switch (warning canceling switch assembly) on.

  4. Turn the GTS on.

  5. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Trouble Codes.

  6. According to the display on the GTS, display the Freeze Frame Data for the selected DTC.

    Blind Spot Monitor Master 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main Switch
    Blind spot monitor main switch (warning canceling switch assembly) / ON or OFF
    ON: Blind spot monitor main switch (warning canceling switch assembly) on
    OFF: Blind spot monitor main switch (warning canceling switch assembly) off
    -
    Warning Indicator Turning on (Master)
    State of the outer rear view mirror indicator RH turning on / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in left hand side warning area
      3. Left turn signal: off
      4. Vehicle speed 16 km/h (10 mph) or more
      5. Shift lever in any position except R
      6. Blind spot monitor warning light not illuminated
    -
    Warning Indicator Flashing (Master)
    State of the outer rear view mirror indicator RH flashing / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      1. Vehicle detected in left hand side warning area
      1. Left turn signal: on
      1. Vehicle speed 16 km/h (10 mph) or more
      1. Shift lever in any position except R
      1. Blind spot monitor warning light not illuminated
    -
    Main Switch Indicator Status
    State of the blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) / OFF or ON
    OFF: Indicator not illuminated
    ON: Indicator illuminated
    -
    Warning Indicator Input Circuit Voltage
    The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V
    Indicator illuminated: 2.5 to 7.5 V
    Indicator not illuminated: Below 1 V
    -
    Warning Indicator Input Circuit Current
    The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA
    Indicator illuminated: 5 to 100 mA
    Indicator not illuminated: 0 mA
    -
    Main Switch Indicator Input Circuit Voltage
    Blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly) voltage / Min.: 0 V, Max.: 25.5 V
    Always: 9 to 16 V
    -
    Turn Switch State
    State of the headlight dimmer switch assembly (turn signal light switch) / Left ON, Right ON or OFF
    Left ON: Left side of turn signal light switch on
    Right ON: Right side of turn signal light switch on
    OFF: Turn signal light switch off
    -
    Reverse (Only for AT/CVT)
    State of the shift position R signal / OFF or ON
    ON: Shift lever in R
    OFF: Shift lever in any position except R
    -
    Vehicle Speed
    Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Steering Angle
    Steering angle sensor / Min.: -3072°, Max.: 3070.5°
    Left turn: Increases
    Right turn: Decreases
    -
    Power Supply Voltage
    Power supply voltage / Min.: 0 V, Max.: 50 V
    Always: 11 to 14 V
    -
    Indicator Light Control State
    Outer rear view mirror indicator dimming state / Dim OFF or Dim ON
    Dim OFF: Indicator not dimmed
    Dim ON: Indicator dimmed
    -
    Angle Adjustment by Auto Alignment
    Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg
    Angle adjusted using auto alignment is displayed
    When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
    Number of DTC
    Number of DTC / Min.: 0, Max.: 255
    When system is normal: 0
    When a malfunction is detected: More than 0
    -

    Blind Spot Monitor Slave 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Warning Indicator Turning on (Slave)
    State of the outer rear view mirror indicator LH turning on / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in right hand side warning area
      3. Right turn signal: OFF
      4. Vehicle speed 16 km/h (10 mph) or more
      5. Shift lever in any position except R
      6. Blind spot monitor warning light not illuminated
    -
    Warning Indicator Flashing (Slave)
    State of the outer rear view mirror indicator LH flashing / OFF or ON
    OFF: The following conditions are not met
    1. ON: All of the following conditions are met
      1. Not during initial check
      2. Vehicle detected in right hand side warning area
      3. Vehicle speed 16 km/h (10 mph) or more
      4. Right turn signal: ON
      5. Shift lever in any position except R
      6. Blind spot monitor warning light not illuminated
    -
    Buzzer Sound Status
    State of the RCTA buzzer (blind spot monitor buzzer) / OFF or ON
    OFF: Buzzer not sounding
    ON: Buzzer sounding
    -
    Warning Indicator Input Circuit Voltage
    The outer rear view mirror indicator voltage / Min.: 0 V, Max.: 25.5 V
    Indicator illuminated: 2.5 to 7.5 V
    Indicator not illuminated: Below 1 V
    -
    Warning Indicator Input Circuit Current
    The outer rear view mirror indicator current / Min.: 0 mA, Max.: 255 mA
    Indicator illuminated: 5 to 100 mA
    Indicator not illuminated: 0 mA
    -
    Buzzer Input Circuit Voltage
    RCTA buzzer (blind spot monitor buzzer) voltage / Min.: 0 V, Max.: 25.5 V
    Buzzer not sounding: 11 to 14 V
    Buzzer sounding: Alternating between 0 to 14 V
    -
    Turn Switch State
    State of the headlight dimmer switch assembly (turn signal light switch) / Left ON, Right ON or OFF
    Left ON: Left side of turn signal light switch on
    Right ON: Right side of turn signal light switch on
    OFF: Turn signal light switch off
    -
    Reverse (Only for AT/CVT)
    State of the shift position R signal / OFF or ON
    ON: Shift lever in R
    OFF: Shift lever in any position except R
    -
    Vehicle Speed
    Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
    Vehicle stopped: 0 km/h (0 mph)
    -
    Steering Angle
    Steering angle sensor / Min.: -3072°, Max.: 3070.5°
    Left turn: Increases
    Right turn: Decreases
    -
    Power Supply Voltage
    Power supply voltage / Min.: 0 V, Max.: 50 V
    Always: 11 to 14 V
    -
    Indicator Light Control State
    Outer rear view mirror indicator dimming state / Dim OFF or Dim ON
    Dim OFF: Indicator not dimmed
    Dim ON: Indicator dimmed
    -
    Angle Adjustment by Auto Alignment
    Angle adjusted using auto alignment / Min.: Under -12.8 deg, Max.: Over 12.7 deg
    Angle adjusted using auto alignment is displayed
    When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
    Number of DTC
    Number of DTC / Min.: 0, Max.: 255
    When system is normal: 0
    When a malfunction is detected: More than 0
    -


CLEAR FREEZE FRAME DATA

NOTICE:
Clearing the DTCs will also clear the Freeze Frame Data

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the blind spot monitor main switch (warning canceling switch assembly) on.

  4. Turn the GTS on.

  5. Clear the DTCs and Freeze Frame Data.