REAR SEAT RECLINING CONTROL CABLE (for TMC, TMMR Made) > INSTALLATION |
| 1. INSTALL REAR SEATBACK LOCK ASSEMBLY LH (REAR SEAT LOCK CONTROL CABLE LH) |
Install the rear seatback lock assembly LH (rear seat lock control cable LH) with the 2 nuts.
![]() |
Engage the hook in the order indicated in the illustration.
| 2. INSTALL REAR SEATBACK LOCK ASSEMBLY RH (REAR SEAT LOCK CONTROL CABLE RH) |
| 3. INSTALL ROOM PARTITION BOARD RH |
Engage the 5 clips to install the room partition board RH.
Install the 2 clips.
| 4. INSTALL ROOM PARTITION BOARD LH |
Engage the 4 clips, 2 claws and guide to install the room partition board LH.
| 5. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade) |
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
![]() |
Engage the 5 guides and 3 clips to install the package tray trim panel assembly.
| 6. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade) |
Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
![]() |
Engage the guide and 3 clips to install the package tray trim panel assembly.
| 7. INSTALL REAR SEAT SHOULDER BELT COVER |
![]() |
Engage the 4 guides and 2 claws to install the rear seat shoulder belt cover.
| 8. INSTALL CENTER STOP LIGHT SET (w/o Rear Sunshade) |
Connect the connector.
Temporarily install the center stop light set.
![]() |
Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to engage the 4 claws.
| 9. INSTALL ROOF SIDE INNER GARNISH LH |
Engage the guide.
Engage the 5 clips to install the roof side inner garnish LH.
| 10. INSTALL ROOF SIDE INNER GARNISH RH |
| 11. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH |
![]() |
Connect the floor anchor of the rear seat inner with center belt assembly LH with the bolt.
| *1 | Protruding Part |
| 12. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH |
Install the child restraint seat anchor bracket sub-assembly LH with the 2 nuts.
| 13. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side) |
![]() |
Connect the floor anchor of the rear seat outer belt assembly with the bolt.
| *a | Protruding Part |
| 14. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side) |
![]() |
Connect the floor anchor of the rear seat outer belt assembly with the bolt.
| *a | Protruding Part |
| 15. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
| *1 | Alignment Mark (Red) |
| 16. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
| *1 | Alignment Mark (Blue) |
| 17. INSTALL REAR SIDE SEATBACK ASSEMBLY LH |
Place the rear side seatback assembly LH in the cabin.
Engage the hook to install the rear side seatback assembly LH with the bolt.
Connect the rear seat outer belt assembly to the rear seat shoulder belt guide LH.
| 18. INSTALL REAR SIDE SEATBACK ASSEMBLY RH |
Place the rear side seatback assembly RH in the cabin.
Engage the hook to install the rear side seatback assembly RH with the bolt.
Connect the rear seat outer belt assembly to the rear seat shoulder belt guide RH.
| 19. INSTALL REAR SEAT CUSHION LOCK HOOK |
![]() |
Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.
| 20. INSTALL REAR SEAT CUSHION ASSEMBLY |
Place the rear seat cushion assembly in the cabin.
w/ Seat Heater System:
Engage the 2 clamps.
Connect the connector.
![]() |
Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.
Confirm that the rear seat cushion assembly is firmly installed.
| 21. INSTALL REAR SEATBACK ASSEMBLY LH |
Place the rear seatback assembly LH in the cabin.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
Install the rear seatback assembly LH with the 2 bolts.
![]() |
Engage the fastener as shown in the illustration.
Raise the rear seatback assembly LH.
Connect the rear seat outer belt assembly to the rear seat center shoulder belt guide.
| 22. INSTALL REAR SEATBACK ASSEMBLY RH |
Place the rear seatback assembly RH in the cabin.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
Install the rear seatback assembly RH with the 2 bolts.
![]() |
Engage the fastener as shown in the illustration.
Raise the rear seatback assembly RH.
| 23. INSTALL REAR SEAT HEADREST ASSEMBLY |