Home › Vehicle Interior › SEAT › REAR SEAT RECLINING CONTROL CABLE (for TMC, TMMR Made)

REAR SEAT RECLINING CONTROL CABLE (for TMC, TMMR Made) > REMOVAL

for Preparation Click here



1. REMOVE REAR SEAT HEADREST ASSEMBLY


2. REMOVE REAR SEATBACK ASSEMBLY LH
  1. Disconnect the rear seat outer belt assembly from the rear seat center shoulder belt guide.

  1. Fold down the rear seatback assembly LH.



    B383044E01
  1. Disengage the fastener as shown in the illustration.
    Text in Illustration 
    *1
    Fastener



  1. w/o Seat Heater System:



      B383045
    1. Remove the 2 bolts and rear seatback assembly LH.

      NOTICE:
      Be careful not to damage the vehicle body.



  1. w/ Seat Heater System:



      B383045
    1. Remove the 2 bolts and disconnect the rear seatback assembly LH.



    2. B383047
    3. Disconnect the connector.

    4. Disengage the clamp and remove the rear seatback assembly LH.

      NOTICE:
      Be careful not to damage the vehicle body.



3. REMOVE REAR SEATBACK ASSEMBLY RH
  1. Fold down the rear seatback assembly RH.



    B281552E01
  1. Disengage the fastener as shown in the illustration.
    Text in Illustration 
    *1
    Fastener



  1. w/o Seat Heater System:



      B281553
    1. Remove the 2 bolts and rear seatback assembly RH.

      NOTICE:
      Be careful not to damage the vehicle body.



  1. w/ Seat Heater System:



      B281553
    1. Remove the 2 bolts and disconnect the rear seatback assembly RH.



    2. B383048
    3. Disconnect the connector.

    4. Disengage the clamp and remove the rear seatback assembly RH.

      NOTICE:
      Be careful not to damage the vehicle body.



4. REMOVE REAR SEAT CUSHION ASSEMBLY


    B383050E01
  1. Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.



  1. w/ Seat Heater System:

    1. Disconnect the connector.



    2. B384060
    3. Disengage the 2 clamps.

  1. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



5. REMOVE REAR SEAT CUSHION LOCK HOOK


    B393387
  1. Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure for the RH side and LH side.



6. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
  1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide LH.



    B281557
  1. Remove the bolt.

  1. Disengage the hook and remove the rear side seatback assembly LH.

    NOTICE:
    Be careful not to damage the vehicle body.



7. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
  1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide RH.



    B281556
  1. Remove the bolt.

  1. Disengage the hook and remove the rear side seatback assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



8. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Disconnect the rear door opening trim weatherstrip LH.



9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
  1. Disconnect the rear door opening trim weatherstrip RH.



10. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    B279440
  1. Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.



11. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    B279442
  1. Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.



12. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


  1. Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.


    B380873E01


    Text in Illustration 
    *A
    for Fold Down Seat Type (w/o Seat Heater System)
    *B
    for Fold Down Seat Type (w/ Seat Heater System)
    *C
    for Reclining Seat Type
    -
    -



13. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


    B279454
  1. Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.



14. REMOVE ROOF SIDE INNER GARNISH LH


    B278991
  1. Disengage the 5 clips.

  1. Disengage the guide and remove the roof side inner garnish LH.



15. REMOVE ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure as for the LH side.



16. REMOVE CENTER STOP LIGHT SET (w/o Rear Sunshade)


    E226678E01
  1. Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to disengage the 4 claws.



    E231297
  1. Turn the center stop light set 180 degrees as shown by the arrow in the illustration.

    HINT:
    This makes it easier to disconnect the connector.

  1. Disconnect the connector and remove the center stop light set.



17. REMOVE REAR SEAT SHOULDER BELT COVER


    B271099
  1. Using a moulding remover, disengage the 2 claws and 4 guides and remove the rear seat shoulder belt cover.

    HINT:
    Use the same procedure for the other 2 rear seat shoulder belt covers.



18. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)


    B279448E02
  1. Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape

    HINT:
    Tape the tips of the pliers before use.

  1. Disengage the 5 guides.

  1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.



19. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)


    B382486E01
  1. Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape

    HINT:
    Tape the tips of the pliers before use.

  1. Disengage the guide.

  1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.



20. REMOVE ROOM PARTITION BOARD LH


    B279212
  1. Disengage the guide, 2 claws and 4 clips, and remove the room partition board LH.



21. REMOVE ROOM PARTITION BOARD RH


    B279213
  1. Using a clip remover, remove the 2 clips.

  1. Disengage the 5 clips, and remove the room partition board RH.



22. REMOVE REAR SEATBACK LOCK ASSEMBLY LH (REAR SEAT LOCK CONTROL CABLE LH)


    B279214
  1. Disengage the hook in the order indicated in the illustration.



    B279215
  1. Remove the 2 nuts and rear seatback lock assembly LH (rear seat lock control cable LH).



23. REMOVE REAR SEATBACK LOCK ASSEMBLY RH (REAR SEAT LOCK CONTROL CABLE RH)

HINT:
Use the same procedure as for the LH side.