INSIDE HANDLE LIGHT > REMOVAL |
| 1. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG (for Front Door) |
![]() |
Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.
| 2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH (for Front Door) |
![]() |
Disengage the 3 clips and remove the front door lower frame bracket garnish.
| 3. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Door) |
| 4. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Door) |
| 5. REMOVE FRONT ARMREST ASSEMBLY (for Front Door) |
![]() |
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.
| 6. REMOVE COURTESY LIGHT ASSEMBLY (for Front Door) |
![]() |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
| *A | for LH Side |
| *B | for RH Side |
| *1 | Protective Tape |
Disconnect the connector and remove the courtesy light assembly.
| 7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Front Door) |
![]() |
Put protective tape around the front door panel.
| *1 | Protective Tape |
![]() |
Remove the 3 screws.
Using a clip remover, disengage the 10 clips.
![]() |
Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
| *1 | Reference Boss |
| *2 | Front Door Inner Glass Weatherstrip |
Disengage the reference boss from the front door panel.
Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.
w/o Memory:
Disconnect the connector.
w/ Memory:
Disconnect the 2 connectors.
![]() |
Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.
| 8. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY (for Front Door) |
![]() |
Disengage the 2 claws and guides, and remove the front door inside handle sub-assembly.
| 9. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP (for Front Door) |
![]() |
Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 10. REMOVE FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY (for Front Door) |
![]() |
Disengage the 3 clamps and claw, and remove the front door inside handle illumination light assembly.
| 11. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG (for Rear Door) |
![]() |
Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.
| 12. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (for Rear Door) |
![]() |
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
w/o Seat Heater System:
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
w/ Seat Heater System:
Disconnect the 2 connectors and remove the rear power window regulator switch assembly with rear door armrest base panel.
| 13. REMOVE REAR ARMREST ASSEMBLY (for Rear Door) |
![]() |
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.
| 14. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY (for Rear Door) |
![]() |
Put protective tape around the rear door panel.
| *1 | Protective Tape |
![]() |
Remove the 3 screws.
Using a clip remover, disengage the 8 clips.
![]() |
Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
| *1 | Reference Boss |
| *2 | Rear Door Inner Glass Weatherstrip |
Disengage the reference boss from the rear door panel.
Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.
![]() |
Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.
Disconnect the connector.
![]() |
Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 15. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY (for Rear Door) |
![]() |
Disengage the 2 claws and guide, and remove the rear door inside handle sub-assembly.
| 16. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP (for Rear Door) |
![]() |
Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 17. REMOVE REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY (for Rear Door) |
![]() |
Disengage the 3 clamps and claw, and remove the rear door inside handle illumination light assembly.