Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL RECEIVER (for TMC, TMMR Made)

DOOR CONTROL RECEIVER (for TMC, TMMR Made) > REMOVAL

for Preparation Click here



1. REMOVE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
  1. w/ Seat Heater System:



2. REMOVE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
  1. w/ Seat Heater System:



3. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)


    B383050E01
  1. Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.



  1. w/ Seat Heater System:

    1. Disconnect the connector.



    2. B384060
    3. Disengage the 2 clamps.

  1. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



4. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)
  1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide RH.



    B281556
  1. Remove the bolt.

  1. Disengage the hook and remove the rear side seatback assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



5. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
  1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide RH.



    B281556
  1. Remove the bolt.

  1. Disengage the hook and remove the rear side seatback assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



6. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)


    B290774E01
  1. Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

  1. Disconnect the 2 seat heater connectors.

  1. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



7. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)


    B393387
  1. Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure as for the LH side.



8. REMOVE REAR DOOR SCUFF PLATE RH (for Reclining Seat Type)

HINT:
Use the same procedure for the RH side and LH side .



9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
  1. Disconnect the rear door opening trim weatherstrip RH.



10. REMOVE REAR SEAT SIDE GARNISH RH (for Reclining Seat Type)

HINT:
Use the same procedure for the RH side and LH side .



11. REMOVE ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedure for the RH side and LH side .



12. REMOVE DOOR CONTROL RECEIVER


    B279945
  1. Disconnect the connector.

  1. Remove the bolt and door control receiver.