Home › Power Source / Network ยท NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > FAIL-SAFE CHART

for Preparation Click here



FAIL-SAFE FUNCTION
  1. When communication fails in any of the CAN bus lines (communication lines), a fail-safe function(s) will operate. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.

  2. The following table shows the effects on each system when communication is impossible. (For further details, see the pages for each system.)

    Function
    Control Master
    System Related
    Fail-safe Operation
    Driver Detectable
    DTC Detection
    (ECU that stored DTC)
    Air Conditioning Control
    1. Corrects engine speed, such as for idle up.
    2. Controls outlet air temperature, outlet mode change and airflow volume based on engine coolant temperature signal.
    3. Corrects engine coolant temperature map and changes compressor lock judgment value.
    Air conditioning amplifier assembly
    ECM
    Control is performed based on default coolant temperature of 80°C (176°F).
    -
    U0100
    (Air conditioning amplifier assembly)
    Compressor Control
    1. Judges compressor lock according to engine speed.
    Air conditioning amplifier assembly
    ECM
    Control is performed based on default engine speed of 0 rpm.
    -
    U0100
    (Air conditioning amplifier assembly)
    Simple Load Control
    1. Performs electric load control according to load control level signal.
    Air conditioning amplifier assembly
    Power steering ECU with motor assembly
    Load control is not performed.
    -
    U0131
    (Air conditioning amplifier assembly)
    Panel Dimming Control
    1. Outputs dimmer signal to LIN connected panels according to display dimmer signal.
    Air conditioning amplifier assembly
    Main body ECU (Multiplex network body ECU)
    Dimming mode and non-dimming mode cannot be switched.
    -
    U0142
    (Air conditioning amplifier assembly)
    Destination Identification Control
    1. Changes air conditioning control pattern according to destination.
    Air conditioning amplifier assembly
    Main body ECU (Multiplex network body ECU)
    Maintains the latest state.
    -
    U0142
    (Air conditioning amplifier assembly)
    Ambient Temperature Correction Control
    1. Switches air conditioning system operation condition and corrects value of displayed ambient temperature according to vehicle speed signal.
    Air conditioning amplifier assembly
    Combination meter assembly
    Control is performed based on default vehicle speed of 0 km/h (0 mph).
    1. Correction level for displayed ambient temperature declines.
    2. Correction level for outlet airflow declines.
    U0155
    (Air conditioning amplifier assembly)
    Fuel Consumption Display
    1. Displays graph of fuel consumption per minute and history of total fuel consumption.
    1. Navigation receiver assembly
    2. Radio and display receiver assembly
    1. ECM
    2. Brake actuator assembly
    3. Combination meter assembly
    When communication with ECM or skid control ECU is interrupted:
    1. Display is not updated.
    When communication with combination meter is interrupted:
    1. Display is not updated.
    2. Numeric part of driveable mileage is cleared.
    -
    U0100
    U0129
    U0155
    (Navigation receiver assembly)
    (Radio and display receiver assembly)
    Destination Identification
    1. Identifies destination based on destination and destination package information, and selects the time zone and language used for the display.
    1. Navigation receiver assembly
    2. Radio and display receiver assembly
    Main body ECU (Multiplex network body ECU)
    Destination is identified based on information received before communication is interrupted.
    Time zone and language selection screen are different from actual destination.
    U0140
    (Navigation receiver assembly)
    (Radio and display receiver assembly)
    Vehicle Customization Function
    1. Allows changing of operation and control conditions for vehicle functions via multi-display operation.
    1. Navigation receiver assembly
    2. Radio and display receiver assembly
    1. Smart key ECU assembly (Certification ECU)
    2. Main body ECU (Multiplex network body ECU)
    3. Position control ECU and switch assembly (for Driver side)
    4. Multiplex tilt and telescopic ECU
    1. Customization via multi-display is not possible, but customization via main body ECU is possible.
    2. When an application that uses remote communication is activated (customization/remote diagnosis), the process will be performed regardless of main body ECU remote communication permit/prohibit state.
    Customizable items are not displayed.
    U0073
    (Navigation receiver assembly)
    Door Lock
    1. Controls key linked and automatic door lock/unlock function, key confinement prevention function, etc.
    Main body ECU (Multiplex network body ECU)
    1. ECM
    2. Combination meter assembly
    1. Speed sensitive automatic lock control does not occur.
    2. Shift linked automatic lock control does not occur.
    3. Shift linked automatic unlock control does not occur.
    4. Automatic lock/unlock cannot be changed.
    -
    U0100
    U0155
    (Main body ECU (Multiplex network body ECU))
    Display Automatic Dimming
    1. Display dimming control.
    Main body ECU (Multiplex network body ECU)
    Combination meter assembly
    Automatic dimming control for displays does not operate when taillights are turned on.
    -
    U0155
    (Main body ECU (Multiplex network body ECU))
    Illumination Control
    Main body ECU (Multiplex network body ECU)
    1. ECM
    2. Smart key ECU assembly (Certification ECU)
    1. Interior lights turn off.
    2. Inside handle light turn off.
    When communication with smart key ECU is interrupted:
    1. Interior lights do not turn off right after getting out of the vehicle.
    U0100
    U0327
    (Main body ECU (Multiplex network body ECU))
    Entry Function/Wireless Control
    Main body ECU (Multiplex network body ECU)
    Smart key ECU assembly (Certification ECU)
    Entry lock/unlock control is not possible.
    -
    U0327
    (Main body ECU (Multiplex network body ECU))
    Seat and Mirror Control
    Main body ECU (Multiplex network body ECU)
    1. Position control ECU and switch assembly (for Driver side)
    2. Outer mirror control ECU assembly (for Driver side)
    3. Outer mirror control ECU assembly (for Front passenger side)
    4. Multiplex tilt and telescopic ECU
    5. Smart key ECU assembly (Certification ECU)
    6. Combination meter assembly
    1. Memory function does not operate.
    2. Mirrors cannot be adjusted.
    -
    U0199
    U0200
    U0208
    U0155
    U0327
    U1115
    (Main body ECU (Multiplex network body ECU))
    Parking Assist System Control
    1. Judges shift lever position.
    2. Judges vehicle speed.
    Clearance warning ECU Assembly
    1. ECM
    2. TCM
    3. Combination meter assembly
    4. Main body ECU (Multiplex network body ECU)
    Obstacle detection is stopped.
    -
    When communication with ECM or TCM is interrupted:
    1. U0101
      (Clearance warning ECU Assembly)
    When communication with Main body ECU (Multiplex network body ECU) is interrupted:
    1. U0142 (Clearance warning ECU Assembly)
    When communication with combination meter is interrupted:
    1. U0155
      (Clearance warning ECU Assembly)
    Electric Load Control
    1. Performs idle up according to electric loads.
    ECM
    1. Power steering ECU with motor assembly
    2. Main body ECU (Multiplex network body ECU)
    3. Air conditioning amplifier assembly
    Idle up according to electric loads is not performed.
    -
    -
    Air Conditioning Cooperative Operation
    1. Performs idle up according to compressor load.
    2. Performs air conditioning cut control.
    ECM
    Air conditioning amplifier assembly
    Air conditioning system does not use cooperative controls.
    (Idle up is not performed.)
    Air conditioning system does not operate.
    -
    Charge Control
    1. Performs idle up according to charging request.
    Smart key ECU assembly (Certification ECU)
    1. Main body ECU (Multiplex network body ECU)
    2. Air conditioning amplifier assembly
    Idle up according to charging request is not performed.
    Taillights flicker and blower airflow changes.
    -
    Eco Control
    1. Adjusts throttle response in consideration of actual fuel economy.
    ECM
    1. Main body ECU (Multiplex network body ECU)
    2. Air conditioning amplifier assembly
    Eco mode does not operate.
    -
    -
    Coast Downshift Timing Change According to Air Conditioning Load
    1. Delays upshifts according to warm-up request.
    1. ECM
    2. ECT
    Air conditioning amplifier assembly
    Coast downshift does not occur.
    Coast downshift shock reduction performance deteriorates.
    -
    Power Steering Control
    1. Calculates assist current according to torque sensor value and vehicle speed and drives motor.
    Power steering ECU with motor assembly
    1. ECM
    2. Brake actuator assembly
    3. Steering sensor
    When communication with ECM is interrupted:
    1. Power steering assist not provided.
    When communication with skid control ECU is interrupted:
    1. Control continues based on a default speed of 100 km/h (62 mph) because vehicle speed is indeterminable.
      (Steering wheel feels heavy when the vehicle speed is below 100 km/h (62 mph) and feels light at speeds above 100 km/h (62 mph).)
    EPS warning light illuminates.
    U0100
    U0129
    (Power steering ECU with motor assembly)
    Steering Assist Calculation
    1. Changes assist force based on vehicle speed.
    Power steering ECU with motor assembly
    Brake actuator assembly
    Control continues based on a default speed of 100 km/h (62 mph) because vehicle speed is indeterminable.
    (Steering wheel feels heavy when the vehicle speed is below 100 km/h (62 mph) and feels light at speeds above 100 km/h (62 mph).)
    EPS warning light illuminates.
    U0129
    (Power steering ECU with motor assembly)
    Steering/Steering Angle Sensor Initialization and Zero Point Learning
    Power steering ECU with motor assembly
    Brake actuator assembly
    Steering initialization and zero point learning are not performed.
    EPS warning light illuminates.
    U0129
    (Power steering ECU with motor assembly)
    Assist Map Selection
    1. Selects proper assist map according to destination, engine type, etc.
    Power steering ECU with motor assembly
    1. ECM
    2. Brake actuator assembly
    Default map is used to assist because proper assist map cannot be selected.
    (Steering feel may be different.)
    EPS warning light illuminates.
    U0100
    U0129
    (Power steering ECU with motor assembly)
    Entry Function
    1. Entry lock/unlock, entry luggage compartment open.
    2. Warning.
    3. Performs entry illumination
      (Interior illumination etc).
    1. Main body ECU (Multiplex network body ECU)
    2. Smart key ECU assembly (Certification ECU)
    1. Main body ECU (Multiplex network body ECU)
    2. Combination meter assembly
    Entry unlock is performed again.
    1. Entry lock/unlock or entry luggage compartment open does not operate.
    2. Warning functions (Key confinement, Key not in vehicle, Key reminder etc.) do not operate, Key confinement prevention control does not operate.
    3. Entry illumination does not operate.
    U0142
    U0155
    (Smart key ECU assembly (Certification ECU))
    Wireless Function
    1. Locks and unlocks doors, etc. via remote operation.
    Main body ECU (Multiplex network body ECU)
    Smart key ECU assembly (Certification ECU)
    Wireless lock, unlock and luggage compartment opener do not operate.
    -
    -
    Engine Switch Backlighting Control
    1. Turns on/off engine switch illumination linked with interior lights etc.
    Smart key ECU assembly (Certification ECU)
    Main body ECU (Multiplex network body ECU)
    Engine switch backlighting does not illuminate according to interior lights operation.
    -
    U0142
    (Smart key ECU assembly (Certification ECU))
    Meter Display
    1. Displays vehicle condition and controls indicator lights.
    Combination meter assembly
    1. ECM
    2. Brake actuator assembly
    3. Airbag sensor assembly
    4. Power steering ECU with motor assembly
    5. Main body ECU (Multiplex network body ECU)
    Lights do not illuminate or lights always illuminate.
    Lights do not illuminate properly or do not illuminate at all.
    U0100
    U0129
    U0131
    U0142
    U0151
    (Combination meter assembly)
    Vehicle Speed Display
    Combination meter assembly
    Brake actuator assembly
    Vehicle speed display remains at 0 km/h (0 mph).
    -
    U0129
    (Combination meter assembly)
    Tachometer
    1. Displays engine speed.
    Combination meter assembly
    ECM
    The needle points at 0 rpm.
    -
    U0100
    (Combination meter assembly)
    Coolant Temperature Display
    Combination meter assembly
    ECM
    Display is turned off.
    -
    -
    Engine Start/Stop Switch
    (Power Source Mode Change)
    1. Using start/stop switch signal as trigger, changes power source mode automatically and requests starter operation when conditions are met.
    Smart key ECU assembly (Certification ECU)
    ECM
    -
    -
    U0100
    (Smart key ECU assembly (Certification ECU))
    ABS/TRC/VSC Control
    Brake actuator assembly
    1. ECM
    2. Steering sensor
    3. Airbag sensor assembly
    Control stops.
    Warning lights and indicators illuminate.
    U0073
    U0100
    U0123
    U0126
    (Brake actuator assembly)
    Power Tilt and Power Telescopic Steering Column Control
    1. Starts steering wheel auto return or auto away based on a key removal or insertion signal or equivalent.
    Multiplex tilt and telescopic ECU
    Main body ECU (Multiplex network body ECU)
    -
    Auto return/away control does not operate.
    U0142
    (Multiplex tilt and telescopic ECU))
    Lighting System
    1. Adjusts headlights vertical aiming according to wheel speed and vehicle pitch angle determined using vehicle height sensor.
    2. Swings headlights left or right according to wheel speed and turn radius determined using steering angle.
    AFS ECU
    1. ECM
    2. TCM
    3. Brake actuator assembly
    4. Steering sensor
    5. Main body ECU (Multiplex network body ECU)
    Control stops.
    AFS indicator blinks.
    U0100
    U0101
    U0126
    U0129
    U0142
    (AFS ECU)
    Parking Assist Monitor
    1. Monitors the shift position signal, steering angle signal and vehicle speed, and displays the predicted path guide lines on the screen based on the steering angle when reversing.
    Rear television camera assembly
    1. ECM
    2. Steering sensor
    3. Brake actuator assembly
    4. Main body ECU (Multiplex network body ECU)
    5. Clearance warning ECU assembly
    6. Radio and display receiver assembly (for Radio and Display Type (w/ Parking Assist Monitor System without Parallel Parking Assist Function))
    7. Power steering ECU with motor assembly
    Parking assist monitor function is prohibited.
    1. Predicted path guide lines are not displayed.
    2. All guide lines and the clearance sonar icon are not displayed.
    U0100
    U0126
    U0129
    U0131
    U0140
    U0163
    U1110
    (Rear television camera assembly)
    Seat Position Memory System
    1. Controls the seat position based on operation conditions.
    Position control ECU and switch assembly (for Driver side)
    1. Main body ECU (Multiplex network body ECU)
    2. ECM
    3. Combination meter assembly
    4. Smart key ECU assembly (Certification ECU)
    5. Multiplex tilt and telescopic ECU
    Controls the seat position based on operation conditions.
    -
    -
    Mirror Surface Adjustment
    1. Outer mirror control ECU assembly (for Driver side)
    2. Outer mirror control ECU assembly (for Front passenger side)
    Main body ECU (Multiplex network body ECU)
    Mirror surface position cannot be memorized or recalled.
    -
    U0142
    (Outer mirror control ECU assembly)
    Mirror Heaters
    1. Outer mirror control ECU assembly (for Driver side)
    2. Outer mirror control ECU assembly (for Front passenger side)
    1. Air conditioning amplifier assembly
    2. Main body ECU (Multiplex network body ECU)
    Mirror heaters do not operate.
    -
    U0142
    (Outer mirror control ECU assembly)
    Mirror Retract/Return Operation
    1. Outer mirror control ECU assembly (for Driver side)
    2. Outer mirror control ECU assembly (for Front passenger side)
    Main body ECU (Multiplex network body ECU)
    Mirrors cannot be retracted or returned.
    -
    -
    Reverse-shift Linked Door Mirror Operation
    1. Outer mirror control ECU assembly (for Driver side)
    2. Outer mirror control ECU assembly (for Front passenger side)
    Main body ECU (Multiplex network body ECU)
    Reverse-shift linked door mirror operation is prohibited.
    -
    -
    Mirror Surface Position Memory and Recall
    1. Outer mirror control ECU assembly (for Driver side)
    2. Outer mirror control ECU assembly (for Front passenger side)
    Main body ECU (Multiplex network body ECU)
    Mirror surface position cannot be memorized or recalled.
    -
    -
    Seat Memory Switch Signal Forwarding
    1. Transmits memory switch signal via the CAN bus.
    Main body ECU (Multiplex network body ECU)
    1. Outer mirror control ECU assembly (for Driver side)
    2. Outer mirror control ECU assembly (for Front passenger side)
    Seat position memory settings cannot be memorized or recalled.
    -
    -
    Blind Spot Monitor Control
    1. Detects vehicle in blind spot of adjacent lane and informs driver.
    Blind spot monitor sensor RH
    1. ECM
    2. Steering sensor
    3. Brake actuator assembly
    4. Main body ECU (Multiplex network body ECU)
    Blind spot monitor control is prohibited.
    Displays messages on the multi-information display.
    U0100
    U0126
    U0129
    U0142
    U0232
    (Blind spot monitor sensor RH)