FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > DATA LIST / ACTIVE TEST |
| DATA LIST |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Mirror L / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Seat Memory Switch 1 | M1 switch / ON or OFF | ON: M1 switch on OFF: M1 switch off | - |
| Seat Memory Switch 2 | M2 switch / ON or OFF | ON: M2 switch on OFF: M2 switch off | - |
| Seat Memory Switch 3* | M3 switch / ON or OFF | ON: M3 switch on OFF: M3 switch off | Not applicable |
| Seat Memory Set SW | SET switch / ON or OFF | ON: SET switch on OFF: SET switch off | - |
| +B Voltage Input Value | Power supply for outer mirror control ECU assembly/MIN: 0 V, MAX: 19.98 V | Within range from 11 to 14 V | - |
Enter the following menus: Body / Driver Seat / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Reclining Rear | Reclining switch signal (Rearward) / ON or OFF | ON: Reclining switch (Rearward) on OFF: Reclining switch (Rearward) off | - |
| Reclining Front | Reclining switch signal (Forward) / ON or OFF | ON: Reclining switch (Forward) on OFF: Reclining switch (Forward) off | - |
| Front Vertical Down | Front vertical switch signal (Downward) / ON or OFF | ON: Front vertical switch (Downward) on OFF: Front vertical switch (Downward) off | - |
| Front Vertical Up | Front vertical switch signal (Upward) / ON or OFF | ON: Front vertical switch (Upward) on OFF: Front vertical switch (Upward) off | - |
| Lifter Switch Down | Lifter switch signal (Downward) / ON or OFF | ON: Lifter switch (Downward) on OFF: Lifter switch (Downward) off | - |
| Lifter Switch Up | Lifter switch signal (Upward) / ON or OFF | ON: Lifter switch (Upward) on OFF: Lifter switch (Upward) off | - |
| Slide Rear | Slide switch signal (Rearward) / ON or OFF | ON: Slide switch (Rearward) on OFF: Slide switch (Rearward) off | - |
| Slide Front | Slide switch signal (Forward) / ON or OFF | ON: Slide switch (Forward) on OFF: Slide switch (Forward) off | - |
| Seat Memory No1 | Seat position memorized with M1 switch / Mem or Not Mem | Mem: Memorized Not Mem: Not memorized | - |
| Seat Memory No2 | Seat position memorized with M2 switch / Mem or Not Mem | Mem: Memorized Not Mem: Not memorized | - |
| Seat Memory No3* | Seat position memorized with M3 switch / Mem or Not Mem | Mem: Memorized Not Mem: Not memorized | Not applicable |
| Seat Memory Drv1* | Driver seat position memorized with M1 switch / Mem or Not Mem | Mem: Memorized Not Mem: Not memorized | Not applicable |
| Seat Memory Drv2* | Driver seat position memorized with M2 switch / Mem or Not Mem | Mem: Memorized Not Mem: Not memorized | Not applicable |
| Seat Memory Drv3* | Driver seat position memorized with M3 switch / Mem or Not Mem | Mem: Memorized Not Mem: Not memorized | Not applicable |
| Ignition Switch | Communication state of engine switch signal / ON or OFF | ON: Engine switch to ON signal received OFF: Engine switch off signal not received | - |
| P Switch | Park state signal / ON or OFF | ON: Shift lever in P OFF: Shift lever in a position other than P | - |
| Parking Brake SW | Parking brake switch status / ON or OFF | ON: Parking brake applied OFF: Parking brake released | - |
| Vehicle Speed | Vehicle speed data / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph) | Actual vehicle speed | - |
| Power Voltage | Power supply for front power seat switch LH (w/ Memory) / min: 0.95 V, max: 20.84 V | Within range from 11 V to 14 V | - |
| Slide Position | Seat sliding position / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Reclining Position | Seat reclining position / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Front Vertical Position | Seat front vertical position / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Lifter Position | Seat lifter position / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Slide Pos Mem No1 | Seat slide position memorized with M1 switch / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Reclining Pos Mem No1 | Seat reclining position memorized with M1 switch / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Frnt Vrtcl Pos Mem No1 | Front vertical position memorized with M1 switch / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Lifter Pos Mem No1 | Lifter position memorized with M1 switch / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Slide Pos Mem No2 | Seat slide position memorized with M2 switch / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Reclining Pos Mem No2 | Seat reclining position memorized with M2 switch / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Frnt Vrtcl Pos Mem No2 | Front vertical position memorized with M2 switch / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Lifter Pos Mem No2 | Lifter position memorized with M2 switch / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Slide Pos Mem No3* | Seat slide position memorized with M3 switch / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Reclining Pos Mem No3* | Seat reclining position memorized with M3 switch / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Frnt Vrtcl Pos Mem No3* | Front vertical position memorized with M3 switch / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Lifter Pos Mem No3* | Lifter position memorized with M3 switch / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Motor Status | State of slide motor control/STANDBY, MOVING, LOCK | STANDBY: Slide motor idle MOVING: Slide motor moving LOCK: Slide motor locked | - |
| Slide Position Init Flag | Seat slide limit position memory / ON or OFF | ON: Memorized OFF: Not memorized | - |
| Slide Position Rear Limit | Seat slide position / min: 0000, max: 65535 | Within range from 0000 to 65535 | - |
| Shift P sw (PMN)* | Park state signal / ON or OFF | ON: Shift lever in P OFF: Shift lever in a position other than P | Not applicable |
| Memory Button Buzzer Request | Driver seat buzzer request display / OFF, MOVE, REGISTRY, CANCEL, REG NG, REG WAIT | OFF: Buzzer does not sound MOVE: Request to sound buzzer when starting memory replay REGISTRY: Request to sound buzzer when starting memory registration CANCEL: Request to sound buzzer when canceling memory call registration REG NG: Request to sound buzzer when memory call registration not possible REG WAIT: Request to sound buzzer when starting memory call cabin scan | - |
| Driver Seat Request Command | Driver seat operation request received / OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET | OFF: No instruction MEMORY: Request to memorize MEM MOV: Request to recall memory MEM SOD: Request to replay RET MOV: Request to return AWY MOV: Request to move away AWY SOD: Request to recall away position memory MEM AWY: Request to recall memorized position of seatback MEM RET: Request to restore seatback to memorized position | - |
| Driver Seat POS REQ | Seat memory switch operation value / OFF, MEM1, MEM2, MEM3*, DRV1*, DRV2* or DRV3* | OFF: No operation MEM1: M1 switch operation status MEM2: M2 switch operation status MEM3: M3 switch operation status* DRV1: Other 1 operation status* DRV2: Other 2 operation status* DRV3: Other 3 operation status* | - |
| Away Move Range Scale* | The seat travel distance for the power easy access system / NONE, SMALL, STANDARD or LONG | NONE: Seat travel distance none SMALL: Seat travel distance short STANDARD: Seat travel distance normal LONG: Seat travel distance long | Not applicable |
| Return Move* | Return function / NOT AVL or AVAIL | NOT AVL: Not available AVAIL: Available | Not applicable |
| Return & Away Function* | Return & away function / NOT AVL or AVAIL | NOT AVL: Not available AVAIL: Available | Not applicable |
| Driver Seat Buckle SW* | Driver seat belt buckle switch / OFF or ON | OFF: Driver seat belt unfastened ON: Driver seat belt fastened | Not applicable |
| Slide Pos Mem Drv1* | Seat sliding position memorized with seat memory switch DRV1 / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Reclining Pos Mem Drv1* | Seat reclining position memorized with seat memory switch DRV1 / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Front Vertical Pos Mem Drv1* | Seat front vertical position memorized with seat memory switch DRV1 / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Lifter Pos Mem Drv1* | Seat lifter position memorized with seat memory switch DRV1 / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Slide Pos Mem Drv2* | Seat sliding position memorized with seat memory switch DRV2 / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Reclining Pos Mem Drv2* | Seat reclining position memorized with seat memory switch DRV2 / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Front Vertical Pos Mem Drv2* | Seat front vertical position memorized with seat memory switch DRV2 / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Lifter Pos Mem Drv2* | Seat lifter position memorized with seat memory switch DRV2 / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Slide Pos Mem Drv3* | Seat sliding position memorized with seat memory switch DRV3 / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Reclining Pos Mem Drv3* | Seat reclining position memorized with seat memory switch DRV3 / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Front Vertical Pos Mem Drv3* | Seat front vertical position memorized with seat memory switch DRV3 / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Lifter Pos Mem Drv3* | Seat lifter position memorized with seat memory switch DRV3 / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Return Position* | Return position / min: 0000, max: 65535 | Within range from 0000 to 65535 | Not applicable |
| Number of Trouble Codes | Number of trouble codes / min.: 0 or max.: 255 | Number of DTCs will be displayed | - |
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Door Courtesy | Front door courtesy light switch assembly signal / OPEN or CLOSE | OPEN: Driver door open CLOSE: Driver door closed | - |
| Mem SW No. w/KeyID1 | Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID1 MEM SW1: M1 switch linked with key ID1 MEM SW2: M2 switch linked with key ID1 MEM SW3: M3 switch linked with key ID1* | - |
| Mem SW No. w/KeyID2 | Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID2 MEM SW1: M1 switch linked with key ID2 MEM SW2: M2 switch linked with key ID2 MEM SW3: M3 switch linked with key ID2* | - |
| Mem SW No. w/KeyID3 | Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID3 MEM SW1: M1 switch linked with key ID3 MEM SW2: M2 switch linked with key ID3 MEM SW3: M3 switch linked with key ID3* | - |
| Mem SW No. w/KeyID4 | Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID4 MEM SW1: M1 switch linked with key ID4 MEM SW2: M2 switch linked with key ID4 MEM SW3: M3 switch linked with key ID4* | - |
| Mem SW No. w/KeyID5 | Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID5 MEM SW1: M1 switch linked with key ID5 MEM SW2: M2 switch linked with key ID5 MEM SW3: M3 switch linked with key ID5* | - |
| Mem SW No. w/KeyID6 | Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID6 MEM SW1: M1 switch linked with key ID6 MEM SW2: M2 switch linked with key ID6 MEM SW3: M3 switch linked with key ID6* | - |
| Mem SW No. w/KeyID7 | Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID7 MEM SW1: M1 switch linked with key ID7 MEM SW2: M2 switch linked with key ID7 MEM SW3: M3 switch linked with key ID7* | - |
| Driver Seat Memory1 | Seat position memorized with M1 switch / OFF or ON | OFF: Not memorized ON: Memorized | - |
| Driver Seat Memory2 | Seat position memorized with M2 switch / OFF or ON | OFF: Not memorized ON: Memorized | - |
| Driver Seat Memory3* | Seat position memorized with M3 switch / OFF or ON | OFF: Not memorized ON: Memorized | Not applicable |
Enter the following menus: Body / Master Switch / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Door Lock Switch Status | Multiplex network master switch lock signal/ON or OFF | ON: Lock side of multiplex network master switch pushed OFF: Lock side of multiplex network master switch not pushed | - |
| Door Unlock Switch Status | Multiplex network master switch unlock signal/ON or OFF | ON: Unlock side of multiplex network master switch pushed OFF: Unlock side of multiplex network master switch not pushed | - |
| ACTIVE TEST |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Driver Seat / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Seat Reclining | Seat reclining operation | OFF/Rear/Front | - |
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Lifter Operation | Seat lifter operation | OFF/Down/Up | - |
| Seat Slide Operation | Seat slide operation | OFF/Rear/Front | - |
| Buzzer | Buzzer operation | OFF/ON | - |