Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

DTC    B1324    Lost Communication with Meter

for Preparation Click here


DESCRIPTION

This DTC is stored when a communication error occurs between the navigation receiver assembly and combination meter assembly.

DTC No.
DTC Detection Condition
Trouble Area
B1324
After the navigation receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the ignition switch is ACC, 1 or more times, the navigation receiver assembly cannot receive the signal for 30 seconds or more.
  1. Combination meter assembly
  2. Navigation receiver assembly
  3. Harness or connector

WIRING DIAGRAM


E268494E06


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the I184 navigation receiver assembly connector.

  1. Disconnect the I18 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I184-3 (CNH1) - I18-18 (MSCH)
    Always
    Below 1 Ω
    I184-4 (CNL1) - I18-19 (MSCL)
    Always
    Below 1 Ω
    I184-3 (CNH1) - Body ground
    Always
    10 kΩ or higher
    I184-4 (CNL1) - Body ground
    Always
    10 kΩ or higher
    I184-3 (CNH1) - I184-4 (CNL1)
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I184-3 (CNH1) - Body ground
    Always
    Below 1 V
    I184-4 (CNL1) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT COMBINATION METER ASSEMBLY
  1. Remove the combination meter assembly (Click here).



    E286972E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    18 (MSCH) - 19 (MSCL)
    Always
    108 to 132 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Combination Meter Assembly)



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Remove the navigation receiver assembly (for TMMK Made) (Click here).
    Remove the navigation receiver assembly (for TMC Made) (Click here).



    E286972E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (CNH1) - 4 (CNL1)
    Always
    108 to 132 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Navigation Receiver Assembly)

Result:
Result
Proceed to
OK
A
NG (for TMMK Made)
B
NG (for TMC Made)
C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMMK Made) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMC Made) (Click here)
A


4.REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new or known good one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check that no DTCs are output.

    OK:
    No DTCs are output.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for TMMK Made)
    B
    NG (for TMC Made)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMMK Made) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMC Made) (Click here)
A


5.CHECK METER / GAUGE SYSTEM
  1. Turn the ignition switch to ON and wait 30 seconds.

  1. Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter assembly and the audio system can be operated normally.

    OK:
    Audio system returns to normal.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for TMMK Made)
    B
    NG (for TMC Made)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMMK Made) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMC Made) (Click here)
A

END